Owner's manual

ManualsBrandsEnergenics ManualsHardwareSuper Series Lint Filter 2007

1470 Don Street • Naples, Florida 34104 Telephone: (239) 643-1711

Fax: (239) 643-6081

Customer Service: (800) 944-1711

Installation & Operation Manual

For ENERGENICS 007 Control

Super Series Lint Filters

Descriptions Page

Table of Contents 1

Description of Lint Filter Operation 2

Receiving and Installation 3

Important Installation Considerations 4

Warnings/Cautions 5

Installation Requirements – Dimensions & Erection (Standard) 6

Single Dryer

Installation Requirements – Dimensions & Erection (Roof Curb Cover)

Single Dryer 7

Installation Requirements – Dimensions & Erection (Standard) 8

Multi Dryer

Installation Requirements – Dimensions & Erection (Roof Curb Cover)

Multi Dryer 9

Installation Requirements – Sheet Metal (Standard) Single Dryer 10

Installation Requirements – Sheet Metal (Roof Curb Cover) Single Dryer 11

Installation Requirements – Sheet Metal (Standard) Multi Dryer 12

Installation Requirements – Piping 13

Fire Control System (optional) 14

Proper Application with Booster Fans & Barometric Dampers 15

007 Control Installation Instructions:

UL® Control Schematic & Wiring Diagram 16

Maintenance Requirements 17

Parts List 18

Summary of content (19 pages)

PAGE 1
470 Don Street • Naples, Florida 34104 Telephone: Fax: Customer Service: (239) 643-1711 (239) 643-6081 (800) 944-1711 Installation & Operation Manual For ENERGENICS 007 Control Super Series Lint Filters Descriptions Page Table of Contents 1 Description of Lint Filter Operation 2 Receiving and Installation 3 Important Installation Considerations 4 Warnings/Cautions 5 Installation Requirements – Dimensions & Erection (Standard) Single Dryer 6 Installation Requirements – Dimensions & Erection
PAGE 2
DESCRIPTION OF LINT FILTER OPERATION Your new Energenics Lint Filter operated with a UL approved control represents the most advanced features available in the laundry industry to date. The following list the functions and mode of operation: Blowdown (cleaning) – The Lint Filter will monitor the system backpressure and automatically initiate the blowdown cycle.
PAGE 3
RECEIVING & INSTALLATION Before you sign the Bill of Lading: 1. Receiving- Inspect units inside and out for signs of damage Verify all components are delivered per the Bill of Materials. Report damage to the carrier IMMEDIATELY. Note ALL damage on the Bill of Lading. This is your responsibility and you must file all claims. The filter is fully assembled and ready for installation. The control, valves, and lint bag are in the cardboard box. 2.
PAGE 4
Important Installation Considerations All Energenics Lint Collectors can be mounted indoors or outdoors. If it is mounted outdoors we recommend our Side Discharge or a field installed swept radius elbow (Gooseneck). Do not use a conical cap on the filter exhaust discharge. All solenoid valves should be located inside the building. Also, mount the supplied air pressure gauge at the blowdown pipe on top of the filter.
PAGE 5
Warning and Caution You have purchased the finest lint filter available for your facility. Please follow these instructions to ensure a safe long life for your filter and facility. FAILURE TO FOLLOW THESE INSTRUCTIONS CAN RESULT IN AN UNSAFE OPERATING CONDITION, INCLUDING THE POSSIBILITY OF FIRE. DO NOT OPERATE ANY DRYER CONNNECTED TO THIS FILTER WITHOUT BEING CERTAIN THE FILTER STARTUP HAS BEEN COMPLETED AND THE FILTER IS IN OPERATING CONDITION. Insure it is installed in compliance with local codes.
PAGE 6
PAGE 7
PAGE 8
PAGE 9
PAGE 10
PAGE 11
PAGE 12
PAGE 13
PAGE 14
PAGE 15
PAGE 16
PAGE 17
Maintenance Requirements The frequency of your maintenance requirements depends upon the number of hours of operation and upon variances in your product output. For a single-shift operation, without special problems, the frequency recommended below should suffice. You should set your own schedule based on your experience. 1. WEEKLY Visually inspect the filter inside and outside, its controls and their operation. At time of such inspection, note and correct any discrepancies from normal operation. 2.
PAGE 18
MODEL 140 PART NUMBER DESCRIPTION 14140 14010 14070 14060 14110 14570 14580 14550 14560 B140 10160 10170 WPSC-1 WPSC-3/4 6015 6690 90007 B3B-24DC KL3BRDRC2S Rotor And Rotor Support Assly Inlet Top Half Of Center Section Bottom Half Of Center Section Outlet Lint Screen With Cables (210 Micron) 1st Lint Screen Without Cables (210 Micron) Lint Screen With Cables (160 Micron) 2nd Lint Screen Without Cables (160 Micron) Lint Bag (76” x 27 ½”) Flex Connector (15” Sq.
PAGE 19
MODEL 170 PART NUMBER 17170 17010 17070 17060 17110 17570 17580 17550 17560 B170 10160 10170 WPSC-1 WPSC-3/4 6015 6691 90007 B3B-24DC KL3BRDRC2S DESCRIPTION Rotor And Rotor Support Assly Inlet Top Half Of Center Section Bottom Half Of Center Section Outlet Lint Screen With Cables (210 Micron) 1st Lint Screen Without Cables (210 Micron) Lint Screen With Cables (160 Micron) 2nd Lint Screen Without Cables (160 Micron) Lint Bag (76” x 27 ½”) Flex Connector (15” sq.