ENUTV-DVB-S DVB-S USB TV Tuner (USB DVB-S Video Capture Box / Personal Video Recorder) ENUTV-DVB-S Series User’s Guide Version 1.
ENUTV-DVB-S User’s Guide - User’s Notice This manual is provided “as is” without warranty of any kind, either express or implied, including but not limited to the implied warranties or conditions of merchantability or fitness for a particular purpose.
ENUTV-DVB-S User’s Guide - Contents: Chapter 1: Introduction ..................................................................................................................4 1.1 - Package Contents ...........................................................................................................4 1.2 - System Requirements .....................................................................................................4 Chapter 2: Getting Started...............................................
ENUTV-DVB-S User’s Guide - Chapter 1: Introduction 1.1 - Package Contents The following items are included in the ENUTV-DVB-S package. CD Setup Disc (includes Software Driver and Utility Software) ENUTV-DVB-S device Remote Controller Power adapter User’s Guide or Quick Installation Guide 1.2 - System Requirements IBM PC or compatible USB2.0 compliant interface Intel Pentium IV 2.
ENUTV-DVB-S User’s Guide - Chapter 2: Getting Started 2.
ENUTV-DVB-S User’s Guide 2.2 - Device Driver Installation Before You Begin Make sure that the product is actually installed. (For more information, please refer to Hardware Installation in the previous section.) Turn on or restart your computer. Place the software CD-ROM that comes with the ENUTV-DVB-S in the CD-ROM drive. Then follow the on-screen installation guide below. Device driver installation for Windows® XP Home/Professional Edition 1.
ENUTV-DVB-S User’s Guide 3. Make sure the “Complete” radio button is selected then click “Next” 4. Click “Install” to begin install driver. 2.3 - Install the DirectX® Microsoft DirectX® allows 3D hardware acceleration support in Windows® 98, 2000, Windows® XP/64 bits and Windows Vista™ 32-bit/64-bit. For software MPEG support in Windows 98, you must first install Microsoft DirectX®, and then a MPEG compliant video player. Follow the installation steps below to install MS DirectX®. 1.
ENUTV-DVB-S User’s Guide 3. Click “Accept the agreement” radio button then click “Next” 4. Click “Next” to confirm the installation of DirectX 5. Click “Finish” NOTE: The computer will automatically restart. Please close all programs if any and save files if needed before hitting the “Finish” button. 2.4 - Install the ENUTV-DVB-S Application. 1. Install TV application on Windows XP Home/Professional Edition 1. Insert the installation CD-ROM into the CD-ROM drive.
ENUTV-DVB-S User’s Guide 3. Click “Next” button to start the ENUTV-DVB-S Installation 4. Click “Next” button to accept the default location or choose a different folder Note: We recommend you not to change the default location. 5. Install wizard will configure your new software installation. 6. Click “Finish” button. Note: We recommend restarting your computer right after the Installation Wizard.
ENUTV-DVB-S User’s Guide - Chapter 3: Launch the ENUTV-DVB-S Program First you open the software through double clicking the icon of “DVBPlayer” desktop. By this time, you will see a window such as the following display.
ENUTV-DVB-S User’s Guide 3.1 LNB Setting In the main menu, click the right key on the mouse to display a list, and select “LNB Setting”. You can also click the button on the bottom-right of main menu to display the LNB Setting window. 3.1.1 Load Satellite In the above figure, click [Load] button to enter into Satellite loading window.
ENUTV-DVB-S User’s Guide There are many different satellites, load a default satellite in the transponder list. Click [Load] button under the satellite item. The following picture will display on the screen. Or, you can choose the satellite you need. a) [Name] Press to display the drop-down list, and select the desired satellite from the list. Input the satellite name you want to add. b) [DiSEqC] The item is used to select the DiSEqC port. This is compatible with the DiSEqC 1.0 protocol.
ENUTV-DVB-S User’s Guide 3.1.2 Add Satellite Add a new satellite in the transponder list. Click [Add] button under the Satellite item and select New again in the next submenu. 3.1.3 Modify Satellite Click [Modify] button in the [satellite] column. The satellite parameters dialog box will appear again.
ENUTV-DVB-S User’s Guide 3.1.4 Delete Satellite Delete a satellite in the transponder list. First select the satellite and press the Del button to delete it. 3.1.5 DiSEqC Setting DiSEqC1.2 is a special protocol for dish motor which drives the dish to aim the satellite. a) [East/West] Drive the motor turn to East or West direction until unclench it or reach the limit. b) [Software Limits] Set the east or west limit to ensure the motor will not reach the real limit.
ENUTV-DVB-S User’s Guide 3.2 Channel Scanning Click the [Scan] button to display the Program Scan menu. In the menu, you can click the small pane to select transponder under the current satellite to search channels. You can also click the [Select All] button to select all transponder to scan channel. All the searched channels will be displayed in the bottom of the menu.
ENUTV-DVB-S User’s Guide 3.3 Transponder Parameters 1. Add transponder Add a new transponder in the transponder list. The following figure is transponder parameter dialog box. a) Name: Enter the new name of the TP. b) [Frequency (MHz)] This box indicates the down link frequency of the current transponder. c) [Symbol Rate (KS/s)] This box indicates the symbol rate of the current transponder. d) [Polarity] This box shows the LNB power supply mode.
ENUTV-DVB-S User’s Guide 2. Modify transponder Click the [Modify] button in the [transponder] item. The transponder parameters dialog box will pop up again. 3. Delete transponder Delete a transponder in the transponder list. Select one transponder and press Del. 4. Scan Auto search all the programs. 3.4 IP Receiver This page shows the program table of the current transponder. You can setup the PID parameters which the satellite service provider offers.
ENUTV-DVB-S User’s Guide 3. Available PID Show searched data PID under the current transponder in the table. (Standard PID) 4. Active PID This item shows the current active PID. 5. PID (Hex) Input the PID provided by your service provider. 6. Add PID Add PID value in [PID] and in Available PID table into active PID table. It can be added to 64 PIDs at the most. 7. Delete PID Delete the selected PID in the active PID table. 8. Filter Type Two filter types are available: MAC filter and Dial IP filter.
ENUTV-DVB-S User’s Guide - Chapter 4: Application Programs 4.1 Capture Click the button to open the capture dialog box. When playing, click [Capture] button to capture one still picture and add to the capture window. Click [Save] button to store the captured picture. Click [Delete] button to delete the selected picture from the storing folder. Click [Del ALL] button to delete all the pictures shown on the capture window, and delete them in the storing folder. 4.
ENUTV-DVB-S User’s Guide When the program broadcasts to the starting time that you have established just now, the state appears of recording and producing the button. If you want to watch programs that you record button, it will broadcast from TV window switch over to record programs and produce, click window, then select the recording program that you want to watch from right column, pressing the right key can be loaded and recorded the file. 4.
ENUTV-DVB-S User’s Guide 2. Advanced (1) Decoder: Click the “ ” to select the MPEG decoder. (2) Time Zone: Click the “ ” to select the time zone. 4.5 Function buttons overview 1. Play Click the button Click the button to play the selected channel, recording file in playing status. to stop the selected channel, recording file in stop status. 2. Record When playing live channel, click the button to start recording the video. 3. Stop When playing recording file, click the button to stop playing file. 4.
ENUTV-DVB-S User’s Guide Click “Sat” to display all satellites. Click “Fav” to display all the favorite channels. Click “All” to display all channels. Click “V” to display all TV programs. Click “R” to display all Radio programs.
ENUTV-DVB-S User’s Guide - Chapter 6: Trouble Shooting If any trouble in installation and operation of the DVB-S, please refer to this section or contact the after-sales service department. 6.1 Hardware trouble shooting: If the DVB-S device can not be detected by Windows XP Home/Pro SP2 during the installation, please check the following items: (1) Check whether the USB jack of the PC and the USB cable is OK. (2) Check whether the power supply is OK. (3) Check whether the insertion of the box is OK.
2008/06/30 Version: 1.
