ENLTV-FM3 PCI TV Tuner Adapter with FM Radio User’s Guide
ENLTV-FM3 User’s Guide User’s Notice No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of us.
ENLTV-FM3 User’s Guide Contents: Chapter 1: Introduction ...................................................................................................................... 4 1.1 - Package Contents............................................................................................................... 4 1.2 - System Requirements ........................................................................................................ 4 Chapter 2: Getting Started .....................................
ENLTV-FM3 User’s Guide Chapter 1: Introduction 1.1 - Package Contents The following items are included in the ENLTV-FM3 package. z CD setup disc (includes Software Driver and Utility Software) z ENLTV-FM3 PCI card z Video cable z FM antenna z Remote sensor cable z Remote controller z User’s guide 1.2 - System Requirements z z z z z z z z Intel® Pentium® 4 1.7GHz CPU or above Minimum 256 MB memory Minimum 1GB hard disk space available 1024x768 graphic card, DirectX® 9.
ENLTV-FM3 User’s Guide Chapter 2: Getting Started 2.1 – ENLTV-FM3 Hardware Installation Install the ENLTV-FM3 PCI Card to the computer’s available PCI slot according to your computers manual and new hardware installation procedures. Make sure that the computer’s power cord is unplugged before inserting the ENLTV-FM3 card to the PCI slot. ENLTV-FM3 supports PCI bus 2.1 and above.
ENLTV-FM3 User’s Guide 2.2 - Device Driver Installation 1. Placed the CD software that comes with the ENLTV-FM3 in the CD-ROM drive. (Assuming that the ENLTV-FM3 Tuner card is properly installed to the computer’s PCI slot), then follow the on-screen installation guide below. Device driver installation for Windows® XP Home/Professional Edition/x64 Edition 1. When the computer is powered-on for the very first time during the setup, a message “Found New Hardware Wizard” dialogue box will appear on the screen.
ENLTV-FM3 User’s Guide 5. Click “Next” on driver setup welcome window to continue. 6. Click “Install” to begin install driver. 7. Click “Next” button.
ENLTV-FM3 User’s Guide 8. Click “Continue Anyway” to continue the installation. 9. Click ”Continue Anyway” button 10.
ENLTV-FM3 User’s Guide 11. Click “Finish” to reboot PC. 12. To make sure the driver is properly installed and started, open the “Device Manager”. Please double-click the “Sound, video and game controller”.
ENLTV-FM3 User’s Guide Device driver installation for Windows® Vista 1. After ENLTV-FM3 hardware has been installed, the next time when the computer is powered-on, a message “Found New Hardware” dialogue box will appear on the screen. Click “Cancel” button to close “Found New Hardware” window. 2. Insert the installation CD into the CD-ROM drive. The setup screen will automatically appear. 3. Click the “Setup Driver” button. 4. Select the language then click “Next”.
ENLTV-FM3 User’s Guide 2. Click “Next” on driver setup welcome window to continue. 3. Click “Install” button. 4. Click “Next” button.
ENLTV-FM3 User’s Guide 5. Click “Finish” button. 6. Click “Finish” button. 7. To make sure the driver is properly installed and started, open the “Device Manager”. Please double-click the “Sound, video and game controller”.
ENLTV-FM3 User’s Guide 2.3 - Install the DirectX® Microsoft DirectX® allows 3D hardware acceleration support in Windows® 98, 2000, Windows® XP 32bit/64bit and Windows Vista® 32bit/64bit. For software MPEG support in Windows® 98, you must first install Microsoft DirectX®, and then an MPEG compliant video player. Follow the installation steps below to install MS DirectX®. 1. Insert the installation CD into the CD-ROM drive. The setup screen will automatically appear. 2. Click the “DirectX” button. 3.
ENLTV-FM3 User’s Guide 2.4 - Install the ENLTV-FM3 Utility software. 1. Install TV application on Windows® XP 32bit/64bit 1. Insert the installation CD into the CD-ROM drive. The setup screen should automatically appear. 2. Click the “Setup Utility” 3. Select the language then click “Next”. 4. Click “Next” button.
ENLTV-FM3 User’s Guide 5. Please read the License Agreement and click “Yes” button 6. Make sure the “Typical” radio button is selected then click “Next”. 7.
ENLTV-FM3 User’s Guide 8. Click “Next” button. 9. Click “Finish” to restart your computer NOTE: We recommend restarting your computer right after the Installation Wizard.
ENLTV-FM3 User’s Guide 2. Install TV application on Windows® Vista 32bit/64bit 1. Insert the installation CD into the CD-ROM drive. The setup screen should automatically appear. 2. Click the “Setup Utility” 3. Select the language then click “Next”. 4. Click “Next” button.
ENLTV-FM3 User’s Guide 5. Please read the License Agreement and click “Yes” button 6. Make sure the “Typical” radio button is selected then click “Next” 7.
ENLTV-FM3 User’s Guide 8. Click “Next” 9. Click “Finish” to restart your computer. NOTE: We recommend restarting your computer right after the Installation Wizard.
ENLTV-FM3 User’s Guide Chapter 3: Launch the ENLTV-FM3 Program 3.1 - Running the ENLTV-FM3 for the first time Click “Start”, move your mouse to “Programs\ENLTV-FM3” then click ENLTV-FM3 NOTE: When the ENLTV-FM3 Program is first started, it will prompt you to configure the Device Setting.
ENLTV-FM3 User’s Guide 1. 2. 3. Select the video signal format in your area (NTSC or PAL) from the “TV Tuner Standard” drop-down menu. Click “Next” This step will give you an option to scan for TV channels. Select which signal source you are connected to in the “TV Scan Type” line then click “Search”. There are two types of scans. i. One is scan by TV channel table “Cable”, “Antenna” and “Extend” ii. One is scan by frequency that scans low frequency to high frequency.
ENLTV-FM3 User’s Guide 3.2 - Watch TV programs or movies from DVD/VCR/Camcorder 5.Double click to full screen 4.Channel Control 3.Volume Control 2.Search TV Channel 7.TV wall 6.Channel List 1.Source Switch 1. Source Switch: click it to select TV, Audio/Video or S-Video 2. Search TV channel: click to search available TV channel. 3. Volume control: Adjust the Volume or mute. 4. Channel control: Set channel up or down’ 5. Double click to full screen display or right click for the program menu 6.
ENLTV-FM3 User’s Guide When you do a full screen display, you can use the panel bar to set up your TV box. 1. Fix Panel: To fix the display panel. Show / Hide as mouse drags. 2. Hide Panel: To hide the sub-panel. 3. Snapshot: Same as "Snapshot" button of main panel. 4. TV Wall: To launch TV Wall function, same as "TV Wall" button, 5. Start / Stop Record: Record the current playing audio/video, same as "Start/Stop Record" of main panel. 6.
ENLTV-FM3 User’s Guide 3.4 - Using the Snapshot 1. Click the “Setting” button to setup the image format. 2. The ENLTV-FM3 support BMP and JPEG image format. The default is JPEG. Please choose your desired format. 3. Click “Snapshot” button to capture image. 3.5 - Playback Video 1. Click “Playback” button to select video file. 2.
ENLTV-FM3 User’s Guide Exit: To exit the video playback window, [Esc] or [ALT]+[F4] on keyboard equalized Minimize: To minimize the video playback window, click "MoviePlayer" in desktop taskbar to restore display Hide Control Panel: To hide video control panel, right click video window and select "Control Panel" to restore display Setting: Click to open “Options” dialog and adjust settings for video windows, snapshots and playlist. ImageViewer: To open image folder (refer to “3.6 ImageViewer” on page26.
ENLTV-FM3 User’s Guide 3.6 - ImageViewer 1. Click the “ImageViewer” to retrieve the saved pictures. 2. You can use the “ImageViewer” software to control pictures zoom in/out, or rename. The menu bar contains many function buttons for easy operations, these are: Refresh: To refresh the display snapshot image in current folder. DirBar: Show/Hide the Direct Panel on the left window Pane, through which you can browse and select folder.
ENLTV-FM3 User’s Guide 3.7 – Time-Shifting 1. Right click inside the ENLTV-FM3 video window and select the “Timeshift” function 2. Video is now being recorded to your hard disk while showing live on screen. You can click “pause” button or slide the “timer” to control the current TV show. 3. Click “Stop” button on the control panel or right click inside the ENLTV-FM3 video window and select “Stop” from the context menu to stop the time-shift function.
ENLTV-FM3 User’s Guide 3.8 - Using and setting up the FM Radio NOTE: ENLTV-FM3 is equipped with FM Radio receiver only. There is no AM Radio receiver included. 1. Click the “Switch Video Source” button then select “Radio Mode”. 2. Click the “Setup” button 3. If the list of radio channel is empty, click “Search” button to scan available radio program. 4. At the channel list, you can select radio programs then click “Use Favorite Channel list” button to set the favorite channel.
ENLTV-FM3 User’s Guide Chapter 4: Using the Remote Control The Remote control allows you to operate the ENLTV-FM3 program, such as turning the TV on or off, changing channel and volume, etc. Aim the upper front side of the Remote Control to the Remote Control Receiver as you would do on other infrared remote control. For default button assignments, please refer to the list below: Remote Control Default Settings: 1. Open or Close TV Program. 2. Mute 3. Number keys. 4. Single or Double digits channel. 5.
ENLTV-FM3 User’s Guide Chapter 5: Frequently Asked Questions Q： I can’t use ENLTV-FM3 when I run the software and it shows an error message. A: This problem is because of incorrect sound card device driver, or the driver and software did not mach. 1. Incorrect sound card device driver • Check the Device Manager for any yellow or red markings under “Sound, Video and Game Controller”. If you see yellow or red markings your sound card may be bad or not working correctly.
ENLTV-FM3 User’s Guide Q: How do I uninstall the ENLTV-FM3 software? A: For Windows® Vista, there are two way to uninstall the ENLTV-FM3 Utility software 1. Go to Start > All Program > ENLTV-FM3 > Uninstall ENLTV-FM3. 2. Go to Windows “Control Panel” > “Add or Remove programs” Select ENLTV-FM3 then click “Remove” button Q： Why doesn’t the “Record” function work? I can watch a TV programs fine, but when I hit the “Record” button, nothing is saved to my hard disk drive.
ENLTV-FM3 User’s Guide 32
2009/08/01 Version: 4.
