Safety Instructions
LED Wi-Fi
Flex Light
Model – 58085, 58087, 58088
Your Enbrighten LED Wi-Fi Flex Light
transforms your space with vibrant
colors and dynamic customization — all
using the free Enbrighten Wi-Fi app.
Note: Read all instructions before
installing. Please read all the warning
statements included in these instructions.
Stake mounting
1. Insert the top of a stake into a clip’s
keyhole slot, sliding it forward until it
clicks into place.
INSTALLATION
This flexible LED strand can be planted
in the ground with stakes, installed to
surfaces with clips or simply laid out in
a line or around corners. Select a clean,
sturdy location that is within reach of
an outlet. The maximum distance to the
receptacle is determined by the length
of cord provided.
Power supply
The power supply features a push
button that serves both as a means
of pairing with the app and manual
operation. Mount it using the keyholes
on the back or the tabs on the side.
IMPORTANT: Do not lay power supply
on the ground or where water may
accumulate.
Scan the QR code above or search
Enbrighten on the Apple App Store or
on Google Play
Download the app
Add devices, control
the smart flex lights
from anywhere and
create schedules
Setup and installation
2.
Plug flex light into
GFCI-protected outlet
1.
Install flex light
Setup and installation
2.
Create an account in
the Enbrighten app
1.
Compatible with Amazon Alexa or
Google Assistant-enabled devices
Select "Support" in the Enbrighten app
or follow the steps in the Amazon Alexa
or Google Home app to connect your
Enbrighten account
Voice control
1 2
43
Remotely operate your smart flex lights with the easy-to-
use Enbrighten app. Follow the available instructions and
resources to set up your smart device.
NOTE: For best results, pair your lights near your router prior to installation.
Requires 2.4GHz Wi-Fi connection
Keyholes
Ear-tabs
2 3/8in./60.3mm
7 1/2in./191mm
Do not pull cord tight, leave
slack in loop to prevent strain
on power supply.
Manual
control
button
2. Carefully thread the flex light through
each clip.
3. Firmly plant the stakes into soil or
garden bedding.
Note: If it requires more than a firm
push, loosen the soil or remove debris.
4. Place the clips over the screws —
tightening the screws as needed.
5. Carefully thread the flex light through
the installed clips.
Connect to power
After installing, plug the power cord
into a 120VAC, 60Hz outlet.
Clip mounting
1. Mark the locations for each clip with
a pencil, leaving about 1.5ft. of space
between each.
2. Drill pilot holes on each marking
using a 1/16in. drill bit.
3. Insert the included screws into
the pilot holes with a Phillips-head
screwdriver, leaving about 1/8in. of
remaining space.
Ground mounting
1. Place strand directly onto ground or
garden bedding.
Slide forward
Slide forward
Clicks into place
Locked
in place
Mounting clips
Flex light
MADE IN VIETNAM
Distributed by Jasco Products Company LLC,
10 E. Memorial Rd., Oklahoma City, OK 73114.
This Jasco product comes with a 3-year limited warranty.
Visit www.byjasco.com for warranty details.
Questions? Contact our U.S.-based Consumer Care at
1-800-654-8483 between 7AM-8PM, M-F, Central Time.
Receive exclusive deals and
register your product.
Scan code or visit
byjasco.com/deals.
Read instructions or watch
easy-to-follow video.
Scan code or visit
byjasco.com/58085i.
Instructions
made easy
Like our product?
Leave a review
on your favorite
retailer website or
amazon.com.
Having problems?
Let us know how
we can help. Call
1-800-654-8483
between 7AM-8PM,
M-F, Central Time.
Home automation
is in your palm with
Wi-Fi smart devices
and accessories at
www.enbrightenwifi.com.
Thank you for your purchase!
Register your
product
All brand names shown are trademarks of their respective
owners App Store is a service mark of Apple Inc. Google,
Google Play and Google Home are trademarks of Google
LLC. Amazon, Alexa and all related logos are trademarks
of Amazon.com, Inc. or its aliates.
05/04/2022 v1
WARNING
RISK OF ELECTRIC SHOCK
• OUTLETS USED FOR POWERING FLEX LIGHTS SHALL COMPLY
WITH ALL NATIONAL AND LOCAL ELECTRICAL CODES. CONSULT
LOCAL ELECTRICIAN IF UNSURE OF COMPLIANCE REQUIREMENTS.
• FOR USE ONLY ON GFCI PROTECTED CIRCUITS.
• DO NOT SUBMERGE.
• DO NOT USE AROUND AQUARIUMS.
• FLEX LIGHTS ARE A WET LOCATION PRODUCT AND HAVE NO
SERVICEABLE PARTS.
• DO NOT USE WITH EXTENSION CORD NEAR WATER OR WHERE
WATER MAY ACCUMULATE.
• KEEP LAMPS AT LEAST 16FT. FROM POOLS AND SPAS.
• KEEP PLUGS AND RECEPTACLES DRY.
• AVOID DAMAGE TO THE CORDS AND LAMP ASSEMBLIES DURING
INSTALLATION. PERIODICALLY INSPECT THE FLEX LIGHTS FOR
PHYSICAL DAMAGE OR OTHER DAMAGE CAUSED BY OUTDOOR
EXPOSURE TO THE ELEMENTS.
• REPLACE ANY DAMAGED FLEX LIGHTS.
• DO NOT INSTALL IN LOCATIONS WHERE FLEX LIGHTS CAN BE
STEPPED ON.
• ENSURE FLEX LIGHTS ARE UNPLUGGED FROM POWER DURING
INSTALLATION.
• CHILDREN SHOULD NOT BE ALLOWED TO PLAY WITH FLEX
LIGHTS.
• NOT SUITABLE FOR FIELD CUTTING OR SPLICING.
• UL RECOMMENDS TESTING GFCI CIRCUITS AND RECEPTACLES
EVERY MONTH TO ENSURE PROPER OPERATION.
• DO NOT MOUNT OR SUPPORT FLEXIBLE LIGHT IN A MANNER THAT
CAN DAMAGE THE OUTER JACKET OR CORD INSULATION.
• MATERIAL MAY BECOME BRITTLE WHEN COLD. DO NOT INSTALL
WHERE IT MAY BE STEPPED ON OR SUBJECT TO PHYSICAL
DAMAGE.
• DO NOT USE WITH EXTENSION CORD NEAR WATER OR WHERE
WATER MAY ACCUMULATE. FOR USE ONLY ON GFCI PROTECTED
CIRCUITS.
RISK OF FIRE
• NOT INTENDED FOR INSTALLATION IN CEILINGS, SOFFITS,
CABINETS, ATTICS, OR OTHER ENCLOSED SPACES.
• DO NOT INSTALL NEAR FLAMMABLE LIQUIDS.
• DO NOT COVER FLEXIBLE LIGHT AS THE COVERING MAY CAUSE
THE FLEXIBLE LIGHT TO OVERHEAT AND MELT OR IGNITE.
• TO PREVENT OVERHEATING, DO NOT ALLOW CONTACT BETWEEN
FLEXIBLE LIGHT CABLES OR PARTS OF THE FLEXIBLE LIGHT
CABLE. MAINTAIN AT LEAST 12MM (0.47IN.) SPACING BETWEEN
LIGHT CABLE OR LIGHT CABLE PARTS.
• UNCOIL FLEXIBLE LIGHT PRIOR TO PLUGGING IN.
Refer to the manual or visit www.byjasco.com for limitations and restrictions
on warranties and the product registration information.
WARNING: When using outdoors use portable luminaires, basic safety
precautions should always be followed to reduce the risk of fire, electrical
shock, and personal injury, including the following:
Ground fault circuit interrupter (GFCI) protection is to be provided on the
circuit(s) or outlet(s) to be used for the wet location portable luminaire.
Receptacles are available having built-in GFCI protection and are able to be
used for this measure of safety. The maximum distance to the receptacle is
determined by the length of cord provided.
WARNING: Keep these bags away from babies and children. Do not use in
cribs, beds, carriages, or playpens. The thin film may cling to nose and mouth
and prevent breathing.
WARRANTY INFORMATION: This Jasco product is warrantied for three
years with a limited-lifetime replacement warranty on Enbrighten LED light
source only.
READ ALL INSTRUCTIONS
SAVE THESE INSTRUCTIONS.
MANUAL OPERATION
Press the button on the power
supply to cycle through each of the
following color settings:
1. White, 100% brightness
2. White, 50% brightness
3. White, 25% brightness
4. Color fade
5. Red
6. Green
7. Blue
8. Yellow
9. Purple
10. Pink
11. Orange
12. Teal
13. Holiday
14. July 4th
15. Rainbow
16. Twinkle
17. OFF
WARNING: When using outdoor use portable luminaires, basic safety
precautions should always be followed to reduce the risk of fire, electric shock,
and personal injury, including the following:
a) Use only three-wire outdoor extension cords that have three-prong
grounding plugs and grounding receptacles that accept the
appliance’s plug.
b) Ground Fault Circuit Interrupter (GFCI) protection is to be provided on
the circuit(s) or outlet(s) to be used for the wet location portable
luminaire. Receptacles are available having built-in GFCI protection and
are able to be used for this measure of safety.
c) Use only with an extension cord for outdoor use, such as an extension
cord of cord type SEW, SEOW, SEOOW, SOW, SOOW, STW, STOW,
STOOW, SJEW, SJEOW, SJEOOW, SJW, SJOW, SJOOW, SJTW, SJTOW,
or SJTOOW.
WARNING!
Input Amps, Max. Location Use
Wet
Model No.
58085
58087
0.25A
0.47A
58088
0.70A
Electrical Ratings
Suppliers Declaration of Conformity |
Model #: 58085, 58087, 58088 |
Jasco Products Co., 10 E. Memorial Rd., Oklahoma City, OK 73114,
www.byjasco.com This device complies with Part 15 of the FCC
and Industry Canada license exempt RSS standards. Operation
is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause
undesired operation.
FCC NOTE: The manufacturer is not responsible for any radio
or TV interference caused by unauthorized modifications
to this equipment. Such modifications could void the user’s
authority to operate the equipment. This equipment complies
with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated
with a 8in minimum distance between the radiator & your body.
NOTE: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and
can radiate radio frequency energy, and if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment o and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent
from which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician
for help.
IMPORTANT
SAFETY
INSTRUCTIONS
This portable luminaire has a polarized plug (one blade is wider than the
other) as a feature to reduce the risk of electric shock. This plug will fit in a
polarized outlet only one way. If the plug does not fit fully in the outlet, reverse
the plug. If it still does not fit, contact a qualified electrician. Never use with an
extension cord unless plug can be fully inserted. Do not alter the plug.
Input: 120V, 60Hz
WARNING!
4.72in
Bending diameter
To prevent failure, do not bend more than 4.72in.