Movie Cube N150H User’s Manual (v1.
TABLE OF CONTENTS 1. Main Features ................................................................................................................... 4 1.1 Front panel .................................................................................................................. 4 1.2 Back panel................................................................................................................... 4 2. Remote Control ............................................................................
SAFETY PRECAUTIONS CAUTIONS: The lightning flash with The exclamation point within Warning: arrowhead symbol, within an To reduce the risk of electric an equilateral triangle is equilateral triangle, is intended shock, don't open the cabinet. intended to alert the user to to alert the user to "dangerous Refer servicing to qualified important operating and voltage" and to prevent from a personnel only. maintenance (servicing). risk of electric shock.
Preface Thank you for purchasing the new N150H! Please read this manual thoroughly before any use and keep it well for future reference. It will help you keep abreast with many of the exciting features and contains important safe measurements and correct operational information, so please read all the information carefully in order to avoid any damage. 1.
2.
3. Welcome Page When turning the power on for the first time, the welcome page will be shown as below: 4. Installation Guide (1) Press [CH+/CH-] key to move the cursor. (2) Press [VOL+/VOL-] key to select the item. (3) Select [Channel Search] and press [OK] key to begin the auto scan. (4) Press [Exit] key to exit menu. 5.
5.1 Program Edit When entering the “ALL TV” menu, which shows as below: (1) Press [CH+/CH-] key to move the cursor. (2) Press [P /P ] key to execute the Page Up/Page down function. (3) Press the color key to execute the corresponding functions in “ALL TV”. 5.1.1 Move (1) Press [CH+/CH-] key to move the cursor and press [RED] key to make a mark. There will be a “moving mark” in the right side of the selected channel as above.
5.1.3 Lock (1) Press [CH+/CH-] key to move the cursor and press [YELLOW] key to make a “lock mark” can be seen on the right side of the highlighted channel. (2) After saving and exiting the menu, if you want to watch the locked channel, a password will be required. 5.1.4 Delete (1) Press [CH+/CH-] key to move the cursor and press [BLUE] key to delete. (2) Press [OK] key to confirm the deletion of the channel or press [exit] key to cancel.
5.2 EPG (1) Pressing [CH+/CH-] key to move the cursor and press [OK] key to enter the “Program Guide” and show EPG information. (2) Press [Exit] to exit “Program Guide” menu. 5.3 Sort (1) Press [CH+/CH-] key to move the cursor to “Sort” then press [VOL-/VOL+] key to change the three kinds of sorting type: by “LCN, “service name”, “ONID”. (2) Press [OK] key to confirm your selection. 5.4 LCN (1) Press [CH+/CH-] key to move the cursor to “LCN” (2) Choose to active/deactivate the LCN mode by pressing on/off.
(1) Press [MENU] key to display the main menu and press [VOL-/VOL+] key to select “Picture “program. Aspect Ratio Press [VOL-/VOL+] key to change option item and press [OK] key to confirm the selection. Resolution Press [VOL-/VOL+] key to change option item and press [OK] key to confirm the selection. TV Format Press [VOL-/VOL+] key to change option item and press [OK] key to confirm the selection. Video Output Press [VOL-/VOL+] key to change option item and press [OK] key to confirm the selection. 7.
(1) Press [CH+/CH-] key to select “Manual Search”. (2) Press [OK] to enter the “Manual Search” menu. (3) Press [VOL-/VOL+] key to select the country. (4) Press [VOL-/VOL+] key to power on/off the “Antenna Power”. (a) You can scan channel by adjusting the “Frequency Channel” number and press [OK] key to start scanning. (b) If you scan channels by Frequency (MHz), “Frequency” and “Bandwidth” are available to adjust. Press [OK] key to save your modifications and the scan will start.
Time Zone When the time offset is “MANUAL“, you can change “GMT+0” value. Power down after Press [VOL-/VOL+] key to setup when to power down automatically 9. Option (1) Press [MENU] key to display the main menu. (2) Press [VOL-/VOL+] key to select the “Option“ menu and OSD Language. (3) Press [VOL-/VOL+] key to choose the language. Subtitles Language Press [VOL-/VOL+] key to choose TV subtitles language. Audio Language Press [VOL-/VOL+] key to choose audio language.
Parental Guidance (1) Press [CH-/CH+] key to move the cursor and press [OK] key to input the Password ”000000”. (2) This sets the program parental controlling level. Set password (1) Press [CH-/CH+] key to move the cursor and press [OK] key to enter the password settings sub-menu. (2) Use the numeric keys of the remote control to set the new password. Restore Factory Default (1) Press [OK] key to enter the sub menu and then [OK] to confirm to restore the default.
(1) Press [MENU] key to display the main menu. (2) Press [VOL-/VOL+] key to select the “USB“ menu. 11.1 Multimedia (1) Press [CH-/CH+] key to enter the “Multimedia” menu. (2) Press [VOL-/VOL+] key to select “Music, Photo, Movie, or PVR“. Music (1) Press [OK] key to enter the “Music” menu. (2) Press [CH-/CH+] key to select the file and press [OK] key to play the music. (3) Press [EXIT] key to return to folder. Photo (1) Press [OK] key to enter the “Photo” menu.
(2) Press [CH-/CH+] key to select the PVR file and press [OK] key to play the video. (3) Press [EXIT] key to return to folder. 11.2 Photo set up (1) Press [CH-/CH+] key to move the cursor and press [OK] enter the “Photo configure” menu. (2) Press [CH-/CH+] and [VOL-/VOL+] key to adjust the slide time. 11.3 Movie set up (1) Press [CH-/CH+] key to move the cursor and press [OK] to enter the “Movie configure” menu. (2) Press [CH-/CH+] and [VOL-/VOL+] key to adjust the aspect ratio. 11.
Recording device (1) Press [CH-/CH+] key to move the cursor and press [OK] key to enter the “Record Device” menu. (2) Then press [VOL-/VOL+] key to choose the DISK. (3) Press [EXIT] key to return to sub-menu. Timeshift function This function is only available when you connect USB storage to the player. Press [Red] to start the timeshift, then press [Stop] to stop the recording.
12. Firmware upgrade You will need a USB flashdrive to upgrade the player. (1) Copy the new firmware to the root directory of a USB stick and connect it to the USB HOST port of the player. (2) Input password “666666” on the main menu, the system will update the firmware automatically. (3) Please restart STB after the software upgrade is complete. 13. Record function If you press [ ] key to start recording, the screen will be displayed as below : Press [ ] key to stop recording. 14. Manage recordings 14.
14.3 Rename (1) Press [GREEN] key to rename the selected program. (2) Press [OK] key to save the changes. 15. Packing list PART N150H player Power adapter Remote control CD with user manuals QUANTITY 1 1 1 1 16. Troubleshooting If you encounter problems when using this product, please check the following points before requesting service.
