Draft as of 31 May 2017 SYSTEM DESCRIPTION AND INSTALLATION MANUAL JetWave™ System mm) in E plane (bend along the short axis of the waveguide). The minimum allowable bend radius for the coax cable is 0.25 inch (6.35 mm). Refer to Figure 4-17. Figure 4-17. View of H Plane and E Plane Bends (g) Connecting the TMA interface, KRFU Power, and Control Interface Power and control signals for the TMA assembly are supplied from the KANDU and is connected to TMA J2 receptacle.
Draft as of 31 May 2017 SYSTEM DESCRIPTION AND INSTALLATION MANUAL JetWave™ System (1) TX-IF connects from the Modman through the bulkhead J4B to KRFU J5. (2) RX-IF connects from the Modman through the bulkhead J3B to KRFU J6. 4 b Make sure that the TX-IF coax cable is banded blue and RX-IF coax cable is banded green at connector ends. c Make sure that the over braid of the cable assembly is terminated to connectors at both KRFU and Modman or the bulkhead interface feed through ends.
Draft as of 31 May 2017 SYSTEM DESCRIPTION AND INSTALLATION MANUAL JetWave™ System (7) 4.8 2 The areas which the risk exists are based upon the location of the antenna. This means personnel operating on the apron, transient personnel, and the general population in the controlled exposure category will not be exposed to levels in excess of the limits. Maintenance personnel working close to the tail must be protected by disabling the transmitter before they approach that area of the aircraft.
Draft as of 31 May 2017 SYSTEM DESCRIPTION AND INSTALLATION MANUAL JetWave™ System • Other antennas or equipment that may block the JetWave™ antenna from being able to see the satellite • The JetWave™ antenna blocking other antennas • Potential interference by the JetWave™ transmitted signal degrading the received signal of other aircraft RF systems • Potential interference by other RF systems degrading the received signal of the JetWave™ system.
Draft as of 31 May 2017 SYSTEM DESCRIPTION AND INSTALLATION MANUAL JetWave™ System KA BAND RADIATION TO MEET A SAFE HUMAN EXPOSURE OF 1 MW/CM2 INSIDE THE AIRCRAFT. WARNING: SERVICE TECHNICIANS AND OPERATORS MUST EXERCISE CARE TO KEEP CLEAR OF THE ANTENNA’S BEAM WHILE PERFORMING OPERATIONAL TESTS OR INSTALLATION VERIFICATION PROCEDURES. DO NOT APPROACH WITHIN 30.3 FEET (9.
Draft as of 31 May 2017 SYSTEM DESCRIPTION AND INSTALLATION MANUAL JetWave™ System CAUTION: F. THE TAIL MOUNT OAE ASSEMBLY IS ELECTROSTATIC-SENSITIVE. STANDARD ELECTROSTATIC-SENSITIVE HANDLING PROCEDURES MUST BE OBSERVED. TMA Airframe Structural Modifications For the installation of TMA, structural modifications to the tail empennage of the airframe may be required to accommodate the additional mass of the antenna assembly and aerodynamic loads.
Draft as of 31 May 2017 SYSTEM DESCRIPTION AND INSTALLATION MANUAL JetWave™ System This is not detailed in this document as the requirement of antenna interface mount is air frame specific. J. TMA Radome and Radome Fairing Depending on the airframe, there may be a need to install radome fairing which adapts to the tail empennage of the aircraft. This is not detailed in this document as the requirement of radome fairing is airframe specific. K.
Draft as of 31 May 2017 SYSTEM DESCRIPTION AND INSTALLATION MANUAL JetWave™ System With the LAIM, the radome will be installed on the Radome skirt fairing assembly. Refer to Figure 4-20. Electrical bonding from the Jetwave™ radome lightning diverters into the airframe must be less than 25 milliohms. NOTE: The segmented diverter strips on Jetwave™ radomes do not have electrical continuity between the segments (buttons).
Draft as of 31 May 2017 SYSTEM DESCRIPTION AND INSTALLATION MANUAL JetWave™ System (3) The JetWave™ system incorporates three fail-safe features to limit the potential for human exposure to non-ionizing radiation: (a) The system will not transmit unless the receiver is receiving a valid signal, therefore if the received signal were to become blocked the transmitter would be disabled.
Draft as of 31 May 2017 SYSTEM DESCRIPTION AND INSTALLATION MANUAL JetWave™ System Table 4-10.
Draft as of 31 May 2017 SYSTEM DESCRIPTION AND INSTALLATION MANUAL JetWave™ System Refer to Figure 4-33 for the LAIM (PN 90404861) outline and installation drawing. Refer to Figure 4-34 for the JetWave™ System - TMA (PN 90400189-0001) interconnect diagram. Refer to Figure 4-35 for the JetWave™ System - FMA (KRFU inside aircraft fuselage) (PN 90400259-0001) interconnect diagram. Refer to Figure 4-36 for the JetWave™ System - FMA (KRFU outside Aircraft Fuselage) (PN 90401047-1) interconnect diagram.
Draft as of 31 May 2017 SYSTEM DESCRIPTION AND INSTALLATION MANUAL JetWave™ System Figure 4-21. (Sheet 1 of 4) Modman Outline and Installation Drawing (90400059-0001, REV F) 23-15-29 © Honeywell International Inc. Do not copy without express permission of Honeywell.
Draft as of 31 May 2017 SYSTEM DESCRIPTION AND INSTALLATION MANUAL JetWave™ System Figure 4-21. (Sheet 2 of 4) Modman Outline and Installation Drawing (90400059-0001, REV F) 23-15-29 © Honeywell International Inc. Do not copy without express permission of Honeywell.
Draft as of 31 May 2017 SYSTEM DESCRIPTION AND INSTALLATION MANUAL JetWave™ System Figure 4-21. (Sheet 3 of 4) Modman Outline and Installation Drawing (90400059-0001, REV F) 23-15-29 © Honeywell International Inc. Do not copy without express permission of Honeywell.
Draft as of 31 May 2017 SYSTEM DESCRIPTION AND INSTALLATION MANUAL JetWave™ System Figure 4-21. (Sheet 4 of 4) Modman Outline and Installation Drawing (90400059-0001, REV F) 23-15-29 © Honeywell International Inc. Do not copy without express permission of Honeywell.
Draft as of 31 May 2017 SYSTEM DESCRIPTION AND INSTALLATION MANUAL JetWave™ System Figure 4-22. (Sheet 1 of 4) Modman Outline and Installation Drawing Variant 2 (90400059-0002, REV A) 23-15-29 © Honeywell International Inc. Do not copy without express permission of Honeywell.
Draft as of 31 May 2017 SYSTEM DESCRIPTION AND INSTALLATION MANUAL JetWave™ System Figure 4-22. (Sheet 2 of 4) Modman Outline and Installation Drawing Variant 2 (90400059-0002, REV A) 23-15-29 © Honeywell International Inc. Do not copy without express permission of Honeywell.
Draft as of 31 May 2017 SYSTEM DESCRIPTION AND INSTALLATION MANUAL JetWave™ System Figure 4-22. (Sheet 3 of 4) Modman Outline and Installation Drawing Variant 2 (90400059-0002, REV A) 23-15-29 © Honeywell International Inc. Do not copy without express permission of Honeywell.
Draft as of 31 May 2017 SYSTEM DESCRIPTION AND INSTALLATION MANUAL JetWave™ System Figure 4-22. (Sheet 4 of 4) Modman Outline and Installation Drawing Variant 2 (90400059-0002, REV A) 23-15-29 © Honeywell International Inc. Do not copy without express permission of Honeywell.
Draft as of 31 May 2017 SYSTEM DESCRIPTION AND INSTALLATION MANUAL JetWave™ System Figure 4-23. (Sheet 1 of 2) APM Outline and Installation Drawing (90401592, REV F) 23-15-29 © Honeywell International Inc. Do not copy without express permission of Honeywell.
Draft as of 31 May 2017 SYSTEM DESCRIPTION AND INSTALLATION MANUAL JetWave™ System Figure 4-23. (Sheet 2 of 2) APM Outline and Installation Drawing (90401592, REV F) 23-15-29 © Honeywell International Inc. Do not copy without express permission of Honeywell.
Draft as of 31 May 2017 SYSTEM DESCRIPTION AND INSTALLATION MANUAL JetWave™ System Figure 4-24. (Sheet 1 of 2) APM Outline and Installation Drawing (90405762, REV A) 23-15-29 © Honeywell International Inc. Do not copy without express permission of Honeywell.
Draft as of 31 May 2017 SYSTEM DESCRIPTION AND INSTALLATION MANUAL JetWave™ System Figure 4-24. (Sheet 2 of 2) APM Outline and Installation Drawing (90405762, REV A) 23-15-29 © Honeywell International Inc. Do not copy without express permission of Honeywell.
Draft as of 31 May 2017 SYSTEM DESCRIPTION AND INSTALLATION MANUAL JetWave™ System Figure 4-25. (Sheet 1 of 3) KANDU Outline and Installation Drawing (90401657, REV E) 23-15-29 © Honeywell International Inc. Do not copy without express permission of Honeywell.
Draft as of 31 May 2017 SYSTEM DESCRIPTION AND INSTALLATION MANUAL JetWave™ System Figure 4-25. (Sheet 2 of 3) KANDU Outline and Installation Drawing (90401657, REV E) 23-15-29 © Honeywell International Inc. Do not copy without express permission of Honeywell.
Draft as of 31 May 2017 SYSTEM DESCRIPTION AND INSTALLATION MANUAL JetWave™ System Figure 4-25. (Sheet 3 of 3) KANDU Outline and Installation Drawing (90401657, REV E) 23-15-29 © Honeywell International Inc. Do not copy without express permission of Honeywell.
Draft as of 31 May 2017 SYSTEM DESCRIPTION AND INSTALLATION MANUAL JetWave™ System Figure 4-26. (Sheet 1 of 3) KANDU Variant 2 Outline and Installation Drawing (90405004, REV C) 23-15-29 © Honeywell International Inc. Do not copy without express permission of Honeywell.
Draft as of 31 May 2017 SYSTEM DESCRIPTION AND INSTALLATION MANUAL JetWave™ System Figure 4-26. (Sheet 2 of 3) KANDU Variant 2 Outline and Installation Drawing (90405004, REV C) 23-15-29 © Honeywell International Inc. Do not copy without express permission of Honeywell.
Draft as of 31 May 2017 SYSTEM DESCRIPTION AND INSTALLATION MANUAL JetWave™ System Figure 4-26. (Sheet 3 of 3) KANDU Variant 2 Outline and Installation Drawing (90405004, REV C) 23-15-29 © Honeywell International Inc. Do not copy without express permission of Honeywell.
Draft as of 31 May 2017 SYSTEM DESCRIPTION AND INSTALLATION MANUAL JetWave™ System Figure 4-27. (Sheet 1 of 9) KRFU, Conduction-Cooled 1, Outline and Installation Drawing (90401573, REV F) 23-15-29 © Honeywell International Inc. Do not copy without express permission of Honeywell.
Draft as of 31 May 2017 SYSTEM DESCRIPTION AND INSTALLATION MANUAL JetWave™ System Figure 4-27. (Sheet 2 of 9) KRFU, Conduction-Cooled 1, Outline and Installation Drawing (90401573, REV F) 23-15-29 © Honeywell International Inc. Do not copy without express permission of Honeywell.
Draft as of 31 May 2017 SYSTEM DESCRIPTION AND INSTALLATION MANUAL JetWave™ System Figure 4-27. (Sheet 3 of 9) KRFU, Conduction-Cooled 1, Outline and Installation Drawing (90401573, REV F) 23-15-29 © Honeywell International Inc. Do not copy without express permission of Honeywell.
Draft as of 31 May 2017 SYSTEM DESCRIPTION AND INSTALLATION MANUAL JetWave™ System Figure 4-27. (Sheet 4 of 9) KRFU, Conduction-Cooled 1, Outline and Installation Drawing (90401573, REV F) 23-15-29 © Honeywell International Inc. Do not copy without express permission of Honeywell.
Draft as of 31 May 2017 SYSTEM DESCRIPTION AND INSTALLATION MANUAL JetWave™ System Figure 4-27. (Sheet 5 of 9) KRFU, Conduction-Cooled 1, Outline and Installation Drawing (90401573, REV F) 23-15-29 © Honeywell International Inc. Do not copy without express permission of Honeywell.
Draft as of 31 May 2017 SYSTEM DESCRIPTION AND INSTALLATION MANUAL JetWave™ System Figure 4-27. (Sheet 6 of 9) KRFU, Conduction-Cooled 1, Outline and Installation Drawing (90401573, REV F) 23-15-29 © Honeywell International Inc. Do not copy without express permission of Honeywell.
Draft as of 31 May 2017 SYSTEM DESCRIPTION AND INSTALLATION MANUAL JetWave™ System Figure 4-27. (Sheet 7 of 9) KRFU, Conduction-Cooled 1, Outline and Installation Drawing (90401573, REV F) 23-15-29 © Honeywell International Inc. Do not copy without express permission of Honeywell.
Draft as of 31 May 2017 SYSTEM DESCRIPTION AND INSTALLATION MANUAL JetWave™ System Figure 4-27. (Sheet 8 of 9) KRFU, Conduction-Cooled 1, Outline and Installation Drawing (90401573, REV F) 23-15-29 © Honeywell International Inc. Do not copy without express permission of Honeywell.
Draft as of 31 May 2017 SYSTEM DESCRIPTION AND INSTALLATION MANUAL JetWave™ System Figure 4-27. (Sheet 9 of 9) KRFU, Conduction-Cooled 1, Outline and Installation Drawing (90401573, REV F) 23-15-29 © Honeywell International Inc. Do not copy without express permission of Honeywell.
Draft as of 31 May 2017 SYSTEM DESCRIPTION AND INSTALLATION MANUAL JetWave™ System Figure 4-28. (Sheet 1 of 3) KRFU, Conduction-Cooled 2, Outline and Installation Drawing (90402347, REV F) 23-15-29 © Honeywell International Inc. Do not copy without express permission of Honeywell.
Draft as of 31 May 2017 SYSTEM DESCRIPTION AND INSTALLATION MANUAL JetWave™ System Figure 4-28. (Sheet 2 of 3) KRFU, Conduction-Cooled 2, Outline and Installation Drawing (90402347, REV F) 23-15-29 © Honeywell International Inc. Do not copy without express permission of Honeywell.
Draft as of 31 May 2017 SYSTEM DESCRIPTION AND INSTALLATION MANUAL JetWave™ System Figure 4-28. (Sheet 3 of 3) KRFU, Conduction-Cooled 2, Outline and Installation Drawing (90402347, REV F) 23-15-29 © Honeywell International Inc. Do not copy without express permission of Honeywell.
Draft as of 31 May 2017 SYSTEM DESCRIPTION AND INSTALLATION MANUAL JetWave™ System Figure 4-29. (Sheet 1 of 3) KRFU, Forced Air Cooled, Outline and Installation Drawing (90401571, REV D) 23-15-29 © Honeywell International Inc. Do not copy without express permission of Honeywell.
Draft as of 31 May 2017 SYSTEM DESCRIPTION AND INSTALLATION MANUAL JetWave™ System Figure 4-29. (Sheet 2 of 3) KRFU, Forced Air Cooled, Outline and Installation Drawing (90401571, REV D) 23-15-29 © Honeywell International Inc. Do not copy without express permission of Honeywell.
Draft as of 31 May 2017 SYSTEM DESCRIPTION AND INSTALLATION MANUAL JetWave™ System Figure 4-29. (Sheet 3 of 3) KRFU, Forced Air Cooled, Outline and Installation Drawing (90401571, REV D) 23-15-29 © Honeywell International Inc. Do not copy without express permission of Honeywell.
Draft as of 31 May 2017 SYSTEM DESCRIPTION AND INSTALLATION MANUAL JetWave™ System Figure 4-30. (Sheet 1 of 4) TMA Outline and Installation Drawing (90401428, REV F) 23-15-29 © Honeywell International Inc. Do not copy without express permission of Honeywell.
Draft as of 31 May 2017 SYSTEM DESCRIPTION AND INSTALLATION MANUAL JetWave™ System Figure 4-30. (Sheet 2 of 4) TMA Outline and Installation Drawing (90401428, REV F) 23-15-29 © Honeywell International Inc. Do not copy without express permission of Honeywell.
Draft as of 31 May 2017 SYSTEM DESCRIPTION AND INSTALLATION MANUAL JetWave™ System Figure 4-30. (Sheet 3 of 4) TMA Outline and Installation Drawing (90401428, REV F) 23-15-29 © Honeywell International Inc. Do not copy without express permission of Honeywell.
Draft as of 31 May 2017 SYSTEM DESCRIPTION AND INSTALLATION MANUAL JetWave™ System Figure 4-30. (Sheet 4 of 4) TMA Outline and Installation Drawing (90401428, REV F) 23-15-29 © Honeywell International Inc. Do not copy without express permission of Honeywell.
Draft as of 31 May 2017 SYSTEM DESCRIPTION AND INSTALLATION MANUAL JetWave™ System Figure 4-31. 23-15-29 © Honeywell International Inc. Do not copy without express permission of Honeywell.