LCD Monitor Quick Installation Guide English Français Deutsch Italiano Español Русский 1
TABLE OF CONTENTS PRECAUTIONS.......................................................................................................... 2 INSTALLATION POWER CONNECTION MAINTENANCE……… TRANSPORTING THE MONITOR 2 2 2 2 GETTING STARTED 3 PACKAGE CONTENTS INSTALLATION OF FIRST USE IDENTIFYING PA RTS AND CONTROLS FUNCTIONS OF THE BUTTONS AND INDICATOR: SETUP CUSTOMIZING YOUR MONITOR Working with OSD Group. Introduction to Hotkeys and the Characteristic Functions………………………………………….
Precauciones Installation 1. Do not cover or block the ventilation ports on the rear of the monitor. 2. Do not install the monitor close to heat sources such as radiators or air ducts, or in a location exposed to direct sunlight, excessive dust, mechanical vibration, or shock. Power connection 1. 2. 3. 4. 5. 5.1 5.2 5.3 5.4 Use the correct power cord for your local voltage. Use an accessible outlet close to the monitor. Do not allow anything to rest on the power cable.
Getting Started Package contents Before beginning, ensure that the carton contains the following items: 1. LCD Monitor 2. Power cord (The plug may vary according to the electrical standard for your area) 3. Video Signal Cable (Analog, D-S U B Cable) 4. Audio cable (optional) 5. CD-ROM (Contains the driver of the monitor, this user’s manual and other information) 6.
Installation of First Use 1. The installation ofthe monitor is very simple. Take the monitor from the packing box and remove all the packing materials. And then put the monitor on the desk carefully; fold the monitor base, so that the monitor can stand on the desk properly. Next, adjust the monitor t o the desired position according to the seat and other factors. Identifying parts and controls 1. The LED indicator and control buttons are as follows: 2.
Setup 1. Connecting video (Note: Before connecting computer, ensure the resolution and refresh rat e of the computer do not exceed the following setting s - resolution: 1280*1024, refresh rate: 75Hz.) 1.1 Turn off your computer 1.2 Connect the video signal cable to the VGA port of your PC, tighten the screws on the connector onto the computer 1.3 Connect the other end of the video signal cable to the VGA-IN port at the back of the monitor, tighten the screws on the connector to the monitor 2.
Customizing your Monitor The On Screen Display (OSD) system provides a full range of customizable tools to optimize your display. While full customization is available, we strongly recommend using the Auto Adjustment function, which is preset to fully optimize your monitor’s performance. Simply press the ＆ buttons simultaneously to engage the Auto Adjustment. It is also recommended that you execute the function following any change made to your display from your computer.
OSD Icon List Icon Functions Auto Adjustment Detail Optimize the picture performance automatically (you may also press _ an d _ buttons simultaneously , while the OSD menu is not shown, to activate the function) Brightness Adjust the luminance level of the screen Contrast Adjust the contrast level (black to white ratio) of the screen Sharpness Adjust the sharpness of the screen Clock Adjust the monitor’s internal sampling clock rate Phase Adjust the monitor internal signal phase Horizontal Posi
OSD Menu Position Adjust the position of OSD menu on the screen. Power Saving Mode Standard Select between Standard and Advanced power saving modes. See addendum for details Fulfill EP A Energy Star power management requirement Advanced Activate monitor Life-Extension function Recall Factory Preset Reset monitor parameters back to factory preset values.
Troubleshooting 1. 2. Symptom No picture LED indicator (at the right side of the monitor) is not lit 1. 2. 3. 1. 2. No picture LED indicator (at the right side of the monitor) is orange 1. 2. 3. Check Items Check if the monitor is turned on (press the button again). Check if the power cord is properly connected to the monitor and power outlet. Check if there is electricity coming from the power outlet (use another device to check for power). Check if your computer is turned on.
Technical Features and Specifications Item LCD Display Display Size Pixel Pitch Resolution Maximum Recommended Max. Display Color Brightness Contrast Ratio V iewing Angle L/R (CR_5) U/D Response T ime (T r+Tf) Signal Input Analog Description 17" TFT active matrix panel 337.92(H ) x 270.336(V) mm 0.264(H ) x 0.264(V) mm SXGA 128 0 x 1024 @75Hz SXGA 128 0 x 1024 @60Hz 16.2M colors 300 cd/m2 (typ.) 500 G1 (typ.) 160° (typ.) 160° (typ.) 12 ms (typ.) D-sub 15 pin Input Frequency Range Horizontal: 31.
Interface Frequency 1. The following frequency range is the working period. If the entered mode is between the below period but does not match the frequency of supported timing, display optimization will not be assured. If the entered mode is out of the working period, the display will be blank (just show “Input Signal Out Of Range”) then go to power saving. 2.
Supported timing list 1. If the selected timing is NOT included in table below, this LCD monitor will use the most suitable available timing.
Note: When the input display mode is not 128 0 X 1024, the image is smoothly expanded to1280 X 1 02 4 dots with scaling engine. After expansion from 65 0 X 350, 64 0 X 400, 64 0 X 480, 72 0 X 400, 83 2 X 6 24, 80 0 X 600, and 1024 X 7 68 resolution, the text may look no t so sharp, and the Graphics may not look proportional.
Addendum Advanced Power Saving M ode 1. Background The traditional monitors have the function of electricity-saving dormancy. Bu t the interval of dormancy is difficult to decide. If the interval is long, the purpose of saving electricity can not be achieved. While if the interval is short, y our computer and LCD monitor will be dormant often. When the LC D monitor becomes dormant, the back lights w ill be turned off immediately.
5.l How can you engage the Monitor Life-Extension function? You may simply use the OSD control to activate the Monitor Life-Extension function. 1. Press the Menu 2. Press or 3. Press the Menu 4. Pres or button to select the Power Saving Mode icon. button to confirm the selection button to select the “Advanced” option in the Power Savin g Mode function. 5. Press the Menu 6. Press button to activate the OSD menu o 7. Press the Menu button to confirm the selection button to select the Exit icon.
Regulations FCC compliance 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 2. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
TCO’99 Congratulations! You have just purchased a TCO’99 approved and labeled product! Your choice has provided you wit h a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and also to the further development of environmentally adapted electronics products.
Environmental requirements Flame retardants Flame retardants are present in printed circuit boards, cables, wires, casings and housings. Their purpose is to prevent, or at least to delay the spread of fire. Up to 30% of the plastic in a computer casing can consist of flame retardant substances. Most flame retardants contain bromine or chloride, and those flame retardants are chemically related to another group of environmental toxins, PCBs.
