EA1350D EA11 35 EA 350D 50 0D 0D EA1800D EA11 80 EA 800D 00 00D 0D CLASS-D MONO AMPLIFIERS Installation & Operating Manual Einbau- & Bedienungsanleitung EA1350-1800D Manual (EDF).indd 1 28.02.
CONTENTS 1. DESIGN FEATURES Page 5 2. CONNECTIONS & CONTROLS 6-8 2.1 FRONT PANEL CONNECTIONS & CONTROLS 6-7 2.2 REAR PANEL CONNECTIONS 8 2.3 SPEAKER IMPEDANCE & POWER WIRE INFO 9 3. AMPLIFIER MOUNTING 9 4. WIRE ROUTING 10 4.1 MAIN POWER WIRES 10 4.2 RCA & REMOTE WIRES 10 4.3 LOUDSPEAKER WIRES 10 4.4 MASTER/SLAVE CONNECTION SCHEMATIC 11 4.5 GenerAl CONNECTION SCHEMATIC 12 5. CROSSOVER ADJUSTMENTS 13 5.1 LOWPASS CROSSOVER FREQUENCY ADJUSTMENT 13 5.
INHALT 1. TECHNISCHER AUFBAU / MERKMALE Seite 17 2. ANSCHLÜSSE & BEDIENUNGSELEMENTE 18-20 2.1. EINGÄNGE & FUNKTIONEN AM FRONT PANEL 18-19 2.2 EINGÄNGE AM REAR PANEL 20 2.3 LAUTSPRECHER-IMPEDANZ & POWERKABEL INFO 21 3. MONTAGE DES VERSTÄRKERS 21 4. VERKABELUNG / ELEKTRISCHER ANSCHLUSS 22 4.1 HAUPT-STROMKABEL 22 4.2 CINCH- & REMOTE KABEL 22 4.3 LAUTSPRECHERKABEL 22 4.4 23 MASTER/SLAVE ANSCHLUSS-SCHEMA 4.5 GENERELLES ANSCHLUSS-SCHEMA 24 5.
Congratulations! And thank you for choosing this EMPHASER EA1350D/EA1800D digital mono amplifier! To maximize the performance of this amplifier and your car audio system install, we recommend that you acquaint yourself thoroughly with all capabilities and features of this EMPHASER amplifier. Please read this manual carefully, before attempting the installation and retain this manual and your purchasing / installation receipts for future reference.
1. DESIGN FEATURES ■ CAR AUDIO AMPLIFIER: This EMPHASER class-D amplifier allows the cross-over controlled amplification of subwoofer systems ■ DASH-MOUNT REMOTE LOWPASS LEVEL CONTROL: A compact „Lowpass-Level“ remote control unit can be mounted close to the drivers seat. This control device allows the convenient level adjustment of the bass volume.
2. CONNECTIONS & CONTROLS 2.
REAR PANEL EA1350D 1 2 3 4 3 5 6 78 9 bl REAR PANEL EA1800D 1 2 3 4 3 5 6 78 9 bl EA1350-1800D Manual (EDF).indd 7 28.02.
2.3 Speaker Impedance & POWER WIRE INFO The heat dissipation capacity of this amplifier has been designed to cope with very low impedance loads.
4. WIRE ROUTING 4.1 Main Power WIRES Run the positive main power cable („+12 V“) directly from the positive terminal of the car battery to the amplifier. For protection of your car audio system against electrical fire hazards, resulting from a short-circuit of the main power cable to chassis ground a main fuse holder must be inserted within the first 30 cm of the positive main power cable.
4.5 GENERAL CONNECTION SCHEMATIC 12 EA1350-1800D Manual (EDF).indd 12 28.02.
5. CROSSOVER ADJUSTMENTS 5.1 LOWPASS CROSSOVER FREQUENCY ADJUSTMENT Note: Before you attempt to adjust the lowpass crossover frequency, you must set the subsonic highpass filter to its lowest position (10 Hz). The LOWPASS cut-off frequency setting depends on some variables. As a rule of thumb, settings in a range between 60 to 90 Hz will render best sonic results. If you use this amp for SPL scores, it is advisable to set the lowpass crossover frequency above 80Hz.
5.4 PHASE-SHIFT ADJUSTMENT The phase shift function of the EA1350D/EA1800D can not be deactivated, as it is permanently in the signal chain. The phase-shift control enables you to match the acoustical phase relations of subwoofer and the speaker system playing in the front doors. The target is, that both speaker systems, normally separated by aprox. 3m of distance shall play acoustically “in-phase” at the drivers seat location.
EA1350-1800D Manual (EDF).indd 15 28.02.
Herzlichen Glückwunsch! Wir danken Ihnen, dass Sie sich zum Kauf dieses ����������������������������������������� EA1350D/EA1800D�������������������������� Verstärkers von EMPHASER entschieden haben. Damit Sie die Wiedergabequalität und die Leistungsfähigkeit Ihres Verstärkers voll ausschöpfen können, möchten wir Sie bitten, sich eingehend mit den Möglichkeiten und technischen Features dieses Verstärkers vertraut zu machen.
1. TECHNISCHER AUFBAU/MERKMALE ■ CAR AUDIO Verstärker: Dieser Verstärker dient zum Antrieb von Hochleistungs-Subwoofer Systemen. ■ Subwooferpegelregelung über externe Kabelfernbedienung: Die im Fond des Fahrzeuges montierbare kleine Fernbedienung ermöglicht die bequeme Anpassung der Lautstärke des Subwoofers vom Fahrersitz aus. ■ DIGITAL VERSTÄRKER: Eine Class-D Verstärkerschaltung sorgt für enorm hohe Ausgangsleistungen mit sehr hohem Wirkungsgrad.
2. ANSCHLÜSSE & BEDIENUNGSELEMENTE 2.1.
REAR PANEL EA1350D 1 2 3 4 3 5 6 78 9 bl REAR PANEL EA1800D 1 2 3 4 3 5 6 78 9 bl 19 EA1350-1800D Manual (EDF).indd 19 28.02.
2.3 LAUTSPRECHER IMPEDANZ & POWERKABEL INFO Die Wärmekapazität der Kühlrippen dieser Endstufe wurde bei dieser Verstärker-Serie für niederohmige Lasten ausgelegt.
4. Verkabelung/Elektrischer Anschluss Halten Sie den Verstärker an den gewünschten Ort und markieren Sie mit einem geeigneten Filzstift die Bohrposition der Befestigungslöcher. Mit der gebotenen Vorsicht bohren Sie nun die angezeichneten Löcher mit einem 2,5 oder 3 mm Bohrer. ACHTUNG: Die Endstufe darf niemals direkt auf die Fahrzeugmasse des Kfz’s geschraubt werden! Verwenden Sie die beigelegten Gummi-Isolatoren um die Endstufe(n) von der Fahrzeugmasse isoliert zu montieren.
4.5 GENERELLES ANSCHLUSS-SCHEMA 24 EA1350-1800D Manual (EDF).indd 24 28.02.
5. EINSTELLUNG DER FREQUENZWEICHE 5.1 TIEFPASS TRENNFREQUENZ ACHTUNG! Drehen Sie das „SUBSONIC“ Potentiometer auf 10 Hz – bevor Sie sich an die Einstellung des Tiefpassreglers machen. Die zu wählende Trennfrequenz des Tiefpasses (LPF) beim Betrieb eines Subwoofers sollte ungefähr im Bereich zwischen 60 bis 90 Hz liegen. Falls die Endstufe für SPL Einsatz verwendet werden soll, darf die Tiefpassfrequenz nicht unter 80 Hz eingestellt werden.
5.4 EINSTELLUNG VOM PHASE-SHIFT Der Phase-Shift Regler ermöglicht die Beeinflussung der Phasenlage des angeschlossenen Subwoofer Systems. Mit diesem Regler – und gegebenenfalls durch zusätzliches Umpolen des Subwoofers, ist es möglich eine perfekte akustische Phaselage zwischen dem Subwoofer und dem Frontsystem (oder auch den Kickbässen, wenn vorhanden) zu erzielen.
6. TECHNISCHE SPEZIFIKATIONEN EA1350D CLASS-D MONO VERSTÄRKER 520W x 1 @ 4 Ohm (< 1.0% THD / 14.4V) 850W x 1 @ 2 Ohm (< 1.0% THD / 14.4V) 1200W x 1 @ 1 Ohm (< 1.0% THD / 14.4V) 1 Ohm stabil Full-MOS-FET Class-D Verstärker Master / Slave Betrieb möglich Variables Subsonicfilter, 10 – 60Hz mit 12dB/Okt. Variables Tiefpassfilter, 30 – 300Hz mit 24dB/Okt. Variabler Phase-Shift von 0 – 180° Variable Eingangsempfindlichkeit von 0.
6. TECHNISCHE SPEZIFIKATIONEN EA1800D CLASS-D MONO VERSTÄRKER 870W x 1 @ 4 Ohm (< 1.0% THD / 14.4V) 1600W x 1 @ 2 Ohm (< 1.0% THD / 14.4V) 2200W x 1 @ 1 Ohm (< 1.0% THD / 14.4V) 1 Ohm stabil Full-MOS-FET Class-D Verstärker Master / Slave Betrieb möglich Variables Subsonicfilter, 10 – 60Hz mit 12dB/Okt. Variables Tiefpassfilter, 30 – 300Hz mit 24dB/Okt. Variabler Phase-Shift von 0 – 180° Variable Eingangs-Empfindlichkeit von 0.
EA1350-1800D Manual (EDF).indd 29 28.02.
7. Limited Warranty Dear customer Please read the warranty specifications below carefully. Should your EMPHASER product require warranty service, please return it to the retailer from whom it was purchased or the distributor in your country. Please do not send any product to EMPHASER Inc. U.S.A. Should you have difficulty in finding an authorized EMPHASER service center, details are available from your local distributor.
8. WARRANTY CARD/GARANTIEKARTE 24 Months Limited Warranty: y) ation Approval onl d Install (Valid with authorize Model name: Class-D Mono Amplifiers ❏ EA1350D ❏ EA1800D Date of purchase: Serial number: Your name: Your address: City: State: ZIP or Postal Code: Country: Your phone number: Installation Approval Dealer’s address & stamp ❏ Installed by authorized dealer ❏ Self-installed by customer Installation date: Inspected and approved by: EMPHASER Inc., Wyoming, Michigan, U.S.A.
EA1350D EA11 35 EA 350D 50 0D 0D EA1800D EA11 80 EA 800D 00 00D 0D Emphaser Inc., Wyoming, Michigan, U.S.A. EA1350-1800D Manual (EDF).indd 32 02.03.