Important Safety Precautions and Explanation of Symbols ! The exclamation point within an equilateral triangle is intended to alert the user to the presence of important installation, operation, and service instructions in this manual. The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltages within the enclosure that may be of sufficient magnitude to constitute a risk of electrical shock to the user.
The power cable for the Fusion 8100 should be unplugged from the outlet during severe electrical storms, or when unused for a long period of time. Only replace the fuse(s) in the Fusion 8100 with a fuse(s) of proper value and voltage rating. The Fusion 8100 should only be cleaned as directed in the manual. Avoid spraying liquids directly onto the Fusion 8100 and NEVER spray liquids into the vents. Care should be taken so that small objects do not fall into the inside of the Fusion 8100.
FCC Interference Statement Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Fusion 8100: User Manual 7.1 Channel AV Receiver Contents Important Safety Precautions and Explanation of Symbols Introduction........................................................................................................................2 About This Manual............................................................................................................3 Features................................................................................................................................
Fusion 8100: User Manual Introduction Thank you for choosing the new Emotiva Fusion 8100 7.1 Channel AV Receiver. The Fusion 8100 leverages cutting edge design and advanced manufacturing methods to pack all the performance and sound quality you would expect to find in separate audiophile components into a revolutionary unit with the convenience, economy, and small form factor of a receiver.
Fusion 8100: User Manual About This Manual This manual will provide you with all the information you need to install and configure the Fusion 8100 to achieve its optimum potential. The manual also includes a brief summary of the features offered by the Fusion 8100 and descriptions of how the controls work. You may wish to record serial numbers or other purchase information on the Notes page at the back of this manual.
Fusion 8100: User Manual Features The Emotiva Fusion 8100 is a reference-caliber home theater receiver with high-performance audio and video processing, seven channels of audiophile quality Class A/B amplification, and a full set of preamp outputs for future expansion.
Fusion 8100: User Manual Unpacking Your Fusion 8100 was carefully packed and should reach you in perfect condition. If you notice any shipping damage or other issues when you unpack it, please contact Emotiva immediately. Gently remove your Fusion 8100 from the packing carton and remove all wrappings and shipping material. It is important to save the box and all packing materials in case your power amp ever needs to be moved or shipped back to the factory for service.
Fusion 8100: User Manual Fusion 8100 Front Panel 1 2 4 3 5 6 7 8 9 1. Input Selector (rotary encoder) Turn this to quickly select between configured inputs; once the correct input is selected, press it to “lock in” your choice. Note: The Input Selector can only select between inputs that are enabled. To access inputs which are not enabled, you must use the Input Menu. 2.
Fusion 8100: User Manual 7. Calibration Microphone Jack Connect the (included) calibration microphone to this jack when you wish to perform automatic room calibration using the Fusion Advanced Room Correction System. For the most accurate results, use only the included calibration microphone. 8. Headphone Jack Connect any standard pair of stereo headphones for high-quality personal listening. When you plug in a pair of headphones, the main volume is automatically muted. 9.
Fusion 8100: User Manual Fusion 8100 Rear Panel Antennas 7.1 Channel Unbalanced Inputs Stereo Unbalanced Inputs Bal. Sub Out SB / Zone 2 SW 7.1 Channel Unbalanced Outputs RS-232 Control Digital Inputs Mix Outputs HDMI Inputs IR In Zone Outputs HDMI Output IR Trigger Out Outs Power Indicators Switch & Inlet Speaker Outputs ANTENNAS SUB OUT AN 1 AN 2 AN 3 AN 4 FL SL CNT SBL 230V CO 1 L CO 2 RS232 CONTROL HDMI 1 R FM OPT1 FR STEREO IN SBL SL FL CNT FR SR SBR SR 7.
Fusion 8100: User Manual Rear Panel - Control and Antenna Connections ANTENNAS SUB OUT AN 1 AN 2 AN 3 AN 4 FL SL CNT SBL 230V CO 1 L RS232 CONTROL HDMI 1 R FM OPT1 FR STEREO IN SBL SL 115V CO 2 FL CNT FR SR SBR SR 7.1 IN SUB SUB SBL/SBR SBR HDMI 2 HDMI 3 ZONE 2 SBL FM SL FL 1 2 AM HDMI OUT DIGITAL IN L R L R L R IR IN IR OUT TRIGGER OUT 1 2 USB FUSION 8100 AV RECEIVER AM 7.
Fusion 8100: User Manual Rear Panel - Power Connections ANTENNAS SUB OUT AN 1 AN 2 AN 3 AN 4 FL SL CNT SBL 230V CO 1 L RS232 CONTROL HDMI 1 R FM OPT1 FR STEREO IN SBL SL 115V CO 2 FL CNT FR SR SBR SR 7.1 IN SUB SUB SBL/SBR SBR HDMI 2 HDMI 3 HDMI 4 DIGITAL IN L R L R L R IR IN IR OUT TRIGGER OUT 1 2 USB FUSION 8100 AV RECEIVER AM ZONE 2 7.1 OUT SBL SL FL HDMI OUT OPT2 MIX OUT ZONE 2 OUT CNT ZONE 3 OUT FR SR SBR 1 230V 115V 2 3 1.
Fusion 8100: User Manual Rear Panel - Video Inputs and Outputs (HDMI) ANTENNAS SUB OUT AN 1 AN 2 AN 3 AN 4 FL SL CNT SBL 230V CO 1 L RS232 CONTROL HDMI 1 R FM OPT1 FR STEREO IN SBL SL 115V CO 2 FL CNT FR SR SBR SR 7.1 IN SUB SUB SBL/SBR SBR HDMI 2 HDMI 3 HDMI 4 L R L R L R IR IN IR OUT TRIGGER OUT 1 2 USB FUSION 8100 AV RECEIVER AM ZONE 2 7.
Fusion 8100: User Manual Rear Panel - Audio Inputs (Analog and Digital) ANTENNAS SUB OUT AN 1 AN 2 AN 3 AN 4 FL SL CNT SBL 230V CO 1 L RS232 CONTROL HDMI 1 R FM OPT1 FR STEREO IN SBL SL FL CNT FR SR SBR SR 7.1 IN SUB SUB SBL/SBR SBR HDMI 2 HDMI 3 ZONE 2 7.1 OUT SBL SL AN 2 AN 3 L R FL L R L ZONE 2 OUT R IR IN IR OUT TRIGGER OUT 1 2 CNT SL CNT FR 1 SR 7.
Fusion 8100: User Manual Rear Panel - Main Audio Outputs (Analog) 1 2 SUB OUT SBL SL FL CNT FR SR SBR SUB 7.1 OUT ANTENNAS SUB OUT AN 1 AN 2 AN 3 AN 4 FL SL CNT SBL 230V CO 1 L RS232 CONTROL HDMI 1 R FM OPT1 FR STEREO IN SBL SL FL CNT FR SR SBR SR 7.1 IN SUB SUB SBL/SBR SBR HDMI 2 HDMI 3 HDMI 4 ZONE 2 7.
Fusion 8100: User Manual Note: The preamp outputs on the Fusion 8100 are configured to deliver the same program content to each channel as the speaker outputs. When the SBL/SBR Speaker Function Switch is pressed in, the preamp outputs designated as SBL and SBR will output signals for Surround Back Left and Surround Back Right (or as Front Left and Front Right Height Speakers, or as Front Bi-Amp outputs, depending on how they are configured).
Fusion 8100: User Manual Rear Panel - Zone and Mix Audio Outputs (Analog) ANTENNAS SUB OUT AN 1 AN 2 AN 3 AN 4 FL SL CNT SBL 230V CO 1 L RS232 CONTROL HDMI 1 R FM OPT1 FR STEREO IN SBL SL 115V CO 2 FL CNT FR SR SR SBR 7.
Fusion 8100: User Manual Fusion 8100 Remote Control 1 2 3 ON STANDBY 12 MODES DIRECT STEREO MODE - MODE + HDMI 1 HDMI 2 HDMI 4 B 2. Mode Buttons TUNER CH+ AM/FM FREQ- CH - 13 14 15 RET DIM UR N MENU ENTER TE 16 MU AY 11 FREQ+ PL 10 ON/OFF DIS 5 6 7 8 9 Press this button when the Fusion 8100 is On to return it to Standby Mode. DIRECT INPUTS TV HDMI 3 4 1.
Fusion 8100: User Manual 4. Tuner Control Buttons Press the Tuner On/Off Button to switch directly to the Tuner as your selected input; press it again to return to your previously selected input. Use the AM/FM Button to switch between the AM and FM bands. The Freq+ and Freq- buttons change between different AM or FM stations, and the CH+ and CH- buttons step between any station presets you have created (station presets are created in the Tuner Setup menu). 5. & 8.
Fusion 8100: User Manual 12. On Button Press this button to turn the Fusion 8100 On when it is in Standby. 13. Menu Button Accesses the front panel menu system and the full-color on-screen display (OSD). 14. Dim Button Press this button to dim the front panel VFD (vacuum fluorescent display) on the Fusion 8100. The display will get gradually brighter each time you press the button, then, when it reaches the brightest setting, drop back to the dimmest setting (dim but not fully off ). 16.
Fusion 8100: User Manual Zone Operation SBL/SBR Speaker Function Switch The Fusion 8100 has seven channels of audiophile quality Class A/B amplification. If the Fusion 8100 is configured as a 7.1 channel receiver, all seven channels are used to power the set of seven surround sound speakers in the main zone. (Press the button IN to select this configuration.
Fusion 8100: User Manual Configuration and Operation Configuring Inputs The Fusion 8100 allows any input connector to be assigned to any input source using the Input Setup configuration screen. Menus The Fusion 8100 is configured using a set of easy-to-use menus. When you first access the menu system using either the Menu button on the Fusion 8100 front panel or the remote control, the menu will open displaying one of the five main menu screens (Input, Mode, Parameter, Zone, or Setup).
Fusion 8100: User Manual Fusion 8100 Menu Tree MENU Input Mode Input Config Playback Parameter Tuner Setup Input Setup Remote Hot Key Zone Speaker Setup Size / Crossover Setup Auto Room EQ Noise Test Option Speaker Distance Load Default Version Page 21 LFE Level
Fusion 8100: User Manual Input Menu Input Tuner Mode Parameter Preset : Zone 01 Setup 87.50MHz TV HDMI 1 HDMI 2 HDMI 3 HDMI 4 CO 1 CO 2 On the Input Menu, use the Up and Down navigation keys to choose an input; press Enter to select the input (make it active). Note: You will NOT be able to access inputs that are NOT Enabled on the Setup / Input Config / Input Setup Submenu from this menu.
Fusion 8100: User Manual Mode Menu Input Mode Parameter Zone Setup Direct Stereo All Stereo PLIIx NEO:6 Dolby D Dolby EX Dolby True The Mode Menu will allow you to select which mode to use to decode your current input source. The Fusion 8100 will normally select the “best” mode that is appropriate for the particular program source you have selected.
Fusion 8100: User Manual Parameter Menu Input Mode Parameter Zone Setup Left Front 00.0 dB Center 00.0 dB Right Front 00.0 dB Left Surround 00.0 dB Right Surround 00.0 dB Left Back / LvH 00.0 dB Right Back / RvH 00.0 dB SubWoofer 00.0 dB Midnight Off Center Width 04 Center Distance 00 Headphone Level 00.0 dB The Parameter Menu allows you to adjust several settings, including the levels of each set of speakers.
Fusion 8100: User Manual Zone Menu Input Mode Parameter Zone 2 Power Zone 2 Source Zone Setup Off FM 87.50MHz Sync by Main Zone 2 Volume 40 Zone 3 Power Off Zone 3 Source FM 87.50MHz Zone 3 Volume Sync by Main 40 The Zone Menu is used to configure the additional audio zones (Zone 2 and Zone 3). For each zone, the zone may be enabled (On) or disabled (Off ), the default Volume level may be set, and the default program source may be selected.
Fusion 8100: User Manual Setup Menu (main setup menu) Input Mode Parameter Zone Setup Input Config Playback Speaker Setup Auto Room/EQ Option Load Default Version The Setup Menu is used to access most of the configuration options on the Fusion 8100.
Fusion 8100: User Manual Setup / Input Config Submenu Input Mode Parameter Zone Setup Input Config Tuner Setup Playback Input Setup Speaker Setup Remote Hot Key Auto Room/EQ Trigger 1 Mode Input Set Option Trigger 2 Mode All Zone PWR Load Default Version The Setup / Input Configuration Submenu is used to access most of the configuration options on the Fusion 8100 related to input selections and configuration of the hot keys on the remote control.
Fusion 8100: User Manual Setup / Input Config / Tuner Setup Submenu Input Mode Parameter Zone Setup Area North America Band FM Freq 87.50 MHz FM Mode Stereo Auto Scan Manual Scan Up Manual Scan Down Memory 1 Trigger 1 ON Trigger 2 OFF The Setup / Input Configuration / Tuner Setup Submenu is used to configure the tuner settings and memory presets for the Fusion 8100.
Fusion 8100: User Manual Setup / Input Config / Input Setup Submenu Input Mode Parameter Zone Setup HDMI ARC Enable Hot Key:TV HDMI 1 Video Last Video HDMI 2 Audio HDMI ARC HDMI 3 Rename TV HDMI 4 LipSync 0 mS Coaxial 1 Input Level 00 dB Coaxial 2 Trigger 1 ON Optical 1 Trigger 2 OFF The Setup / Input Configuration / Input Setup Submenu is used to configure various parameters for each input on the Fusion 8100, including the audio and video source for each, the input name, an in
Fusion 8100: User Manual Setup / Input Config / Remote Hot Key Submenu Input Mode Parameter Zone Setup REMOTE KEY: Assigned to: HOT KEY 1 TV TV HOT KEY 2 HDMI 1 HDMI 1 HOT KEY 3 HDMI 2 HDMI 2 HOT KEY 4 HDMI 3 HDMI 3 HOT KEY 5 HDMI 4 HDMI 4 The Setup / Input Configuration / Remote Hot Key Submenu is used to configure which input is associated with which hot key on the remote control. The Bluetooth hot key (the one with the “B” symbol) is pre-configured and cannot be changed.
Fusion 8100: User Manual Setup / Playback Submenu Input Mode Parameter ANALOG 2 CH LAST USED PCM Direct MULTI PCM Stereo DOLBY 2/0 PLIIx DOLBY D NEO:6 DOLBY EX All Stereo Zone Setup DOLBY HD DTS 2/0 DTS DST-ES DTS-HD The Setup / Playback Submenu allows you to configure which decoder mode is used by default to decode each different type of source signal. Here you can configure which default mode the Fusion 8100 will use to decode each type of input source when it is received.
Fusion 8100: User Manual Setup / Speaker Setup Submenu Input Mode Parameter Input Setup Size/Crossover Playback Noise Test Speaker Setup Speaker Distance Auto Room/EQ LFE Level Option Front Bi-Wire Zone Setup OFF Load Default Version The Setup / Speaker Setup Submenu allows you to access the menus on the Fusion 8100 for configuring speaker sizes and crossovers, levels, and distances.
Fusion 8100: User Manual Setup / Speaker Setup / Size & Crossover Submenu Input Mode Parameter Zone Setup Front L/R Large Center Small 80 Hz Surround L/R Small 80 Hz Back L/R Small 80 Hz FvH None Back/FvH Channel Parameter 2 CH SubWoofer Yes 80 Hz Enhanced Bass Parameter Off Front Slope 12 dB Center Slope 12 dB Surround Slope 12 dB Back/FvH Slope 12 dB SubWoofer Slop 24 dB Load Default The Setup / Speaker Setup / Size & Crossover Submenu allows you to configure the spe
Fusion 8100: User Manual Enhanced Bass is a special function intended to enhance the bass capabilities of systems with both Large front speakers and a subwoofer. When enhanced Bass is set to On, bass frequencies from the front channels are also sent to the subwoofer (even if the front speakers are set to Large). Note: To configure the Fusion 8100 as a “regular 7.
Fusion 8100: User Manual Setup / Speaker Setup / Noise Test Submenu Input Channel : Mode Parameter Zone Setup Left Front 00.0 dB Center 00.0 dB Right Front 00.0 dB Right Surround 00.0 dB Right Back 00.0 dB Left Back 00.0 dB Left Surround 00.0 dB SubWoofer 00.0 dB The Setup / Speaker Setup / Noise Test Submenu allows you manually adjust (trim) the level for each speaker individually. As each speaker is selected, a test tone (modified pink noise) is played from that speaker.
Fusion 8100: User Manual Setup / Speaker Setup / Speaker Distance Submenu Input Mode Parameter Zone Setup Left Front 00.0 ft Center 00.0 ft Right Front 00.0 ft Left Surround 00.0 ft Right Surround 00.0 ft Left Back 00.0 ft Right Back 00.0 ft SubWoofer 00.0 ft The Setup / Speaker Setup / Speaker Distance Submenu allows you to manually adjust the distance from each speaker to your chosen seating position.
Fusion 8100: User Manual Setup / Speaker Setup / LFE Level Submenu Input Mode Parameter Zone Setup EXT 7.1CH 00 dB MULTI PCM 00 dB DOLBY D 00 dB DOLBY HD 00 dB DTS 00 dB DTS-HD 00 dB Load Default The Setup / Speaker Setup / LFE Level Submenu allows you manually trim the subwoofer LFE level for each different type of input signal. (You could use this adjustment, for example, to set the subwoofer to play 1 dB quieter for all Dolby Digital movies, and 3 dB quieter for all 7.
Fusion 8100: User Manual Setup / Auto Room EQ Submenu Input Mode Parameter Input Config Auto Room/EQ Playback Auto EQ Speaker Setup Manual EQ 1 Auto Room/EQ Manual EQ 2 Option Manual EQ 3 Load Default Flat Zone Setup Version The Setup / Auto Room EQ Submenu is used to initiate the Fusion Advanced Room Correction System, and to select which equalization curve is in effect. When the Fusion Advanced Room Correction System is run, it will create and save one room equalization curve.
Fusion 8100: User Manual Fusion Advanced Room Correction System™ The Fusion Advanced Room Correction System (Fusion ARCS) sends a series of test signals through your speakers, measures the results with the (included) calibrated microphone, and configures the Fusion 8100 to make your system sound its best. Even though the actual operation of the Fusion ARCS is very sophisticated, it is very simple to use and will deliver excellent results without manual tweaking in most situations.
Fusion 8100: User Manual • • • • • Avoid moving around the room during the test. It’s best if you pick a spot that doesn’t block or change the sound field to stand or sit while the test is running. The best place is in the rear of the room towards the center of the wall. Avoid walking near the microphone during the test (even if you don’t block any speakers) because reflections from your body will interfere with the accuracy of the results. And, of course, avoid making noise during the test.
Fusion 8100: User Manual Note: The Fusion Advanced Room Correction System is very sophisticated, but no automated system is totally foolproof. Unusual room acoustics, reflections, or unusual speakers can cause it to get incorrect results. If the Fusion ARCS says that the phase of a particular speaker is reversed, it is a good idea to double check your wiring, and the phase of your power amp and speaker. If, however, you find that the Fusion ARCS is mistaken, you can safely ignore its findings.
Fusion 8100: User Manual Note: Moving the selector bar to an EQ choice that isn’t highlighted and pressing Enter selects that choice. At this point (if you have an active input which is subject to EQ) you will be able to preview what that choice sounds like. Moving the selector bar to an EQ choice that is already highlighted, and pressing Enter, takes you into a sub-menu where you can make detailed adjustments to the selected EQ configuration.
Fusion 8100: User Manual The final results are then displayed, and you are prompted to save them. Note: The results displayed by the Fusion Advanced Room Correction System are provided to give you general insight into the areas where corrections have been implemented, and the frequency bands and ranges which are affected by those corrections, and should not be interpreted to literally represent the correction curve itself.
Fusion 8100: User Manual Setup / EQ Submenus (Auto / Manual 1 / Manual 2 / Manual 3) Input Mode Channel : Fc Parameter Zone Setup Front Left Gain Q Band 1: 27.28Hz 0 dB 2 Band 2: 50.74Hz 0 dB 2 Band 3: 96.97Hz 0 dB 2 Band 4: 180.36Hz 0 dB 2 Band 5: 335.49Hz 0 dB 2 Band 6: 641.1Hz 0 dB 2 Band 7: 1.19KHz 0 dB 2 Band 8: 2.21KHz 0 dB 2 Band 9: 4.12KHz 0 dB 2 Band 10: 7.88KHz 0 dB 2 Band 11:14.
Fusion 8100: User Manual With an old style “graphic equalizer”, you were given ten (usually) separate frequency controls, each of which worked like a tone control (you could turn that band either up or down in level). A parametric equalizer is infinitely more flexible. For each channel in each EQ bank you are given eleven control bands. For each control band, you may choose the center frequency (Fc), how narrow or wide a range of frequencies is affected (Q), and then finally the level for that band.
Fusion 8100: User Manual Setup / Option Submenu Input Mode Parameter Zone Setup 09 Input Config OSD Depth Playback OSD Pop Up Speaker Setup HDMI CEC Control Auto Room/EQ HDMI Audio Out Option Standby Video Off Load Default CEC Auto Source Off Version CEC PWR Control Off All Operational On Amplifier The Setup / Options Submenu is used to configure the CEC control options, OSD display options, and Video on Standby feature on the Fusion 8100.
Fusion 8100: User Manual Set CEC Auto Source On to enable CEC commands to be passed between the chosen input device and the Fusion 8100 (the Fusion 8100 will automatically come on when you turn your source component on, and your source component will automatically come on when it is selected on the Fusion 8100). CEC PWR Control will enable your Fusion 8100 and other components to switch each other on and off (so, for example, your TV will come on when you turn on the Fusion 8100).
Fusion 8100: User Manual Setup / Load Default Submenu Input Mode Parameter Zone Setup Input Config Playback Speaker Setup Auto Room/EQ Option Load Default Version The Setup / Load Default Submenu is used to return the Fusion 8100 to factory default settings (and is also used to clear the Fusion 8100’s data and configuration buffers after a firmware update).
Fusion 8100: User Manual Setup / Version Submenu Input Mode Parameter Zone Setup Input Config Main CPU: V1.52.02.51 Playback Bluetooth Module V1.000E Speaker Setup Auto Room/EQ MAC: TV:HDMI 00175348A63B VX2433wm Option Load Default Version The Setup / Version Submenu displays the versions of the various firmware modules in the Fusion 8100.
Fusion 8100: User Manual Example Input Configuration The following is an example of how you might choose to configure your Fusion 8100. In the example, we will be configuring a typical 7.1 surround system, with seven speakers and a powered sub, and a Blu-Ray player and Cable Box as the video and audio sources. The Cable Box is connected to HDMI 1 input, and the Blu-Ray player is connected to the HDMI 2 input. Both input devices, and our monitor, support HD.
Fusion 8100: User Manual Connectivity • • • • • • • • • • • • • • • • • • 4 – HDMI 1.4 inputs with 3D and CEC support. 1 – HDMI 1.4 output with ARC support. 4 – Line inputs (unbalanced, stereo). 1 – 7.1 channel input (7 channels plus sub, unbalanced). 1 – 7.1 channel preamp output (7 channels plus sub, unbalanced). 1 – Balanced subwoofer output. 1 – Integrated Bluetooth receiver. 2 – zone audio outputs (unbalanced, stereo). 1 – audio out (mix out, unbalanced, stereo).
Fusion 8100: User Manual Care and Maintenance Periodic Maintenance Your Fusion 8100 requires no periodic maintenance or calibration. Cleaning your Fusion 8100 • • If necessary, the Fusion 8100 should be cleaned gently with a soft rag. If something sticky gets on the front panel or case of the Fusion 8100, it should be cleaned with a mild cleaning solution applied to a soft rag, followed by wiping with a clean rag dampened with plain water and drying with a soft dry rag or cloth.
Fusion 8100: User Manual Troubleshooting Problem: No power; Standby LED on the front panel of the Fusion 8100 is not lit. • • Verify that your power source is operating correctly. Verify that the Power switch on the rear panel of the Fusion 8100 is turned On. Problem: No video. • • • Verify that your source component and TV or monitor work (connect them together directly). Check your HDMI cables and connectors. Verify that you have the correct Input selected on the Fusion 8100.
Fusion 8100: User Manual Emotiva Audio Corporation Limited Warranty What does this warranty cover? Emotiva Audio Corporation (“Warrantor”) warrants its products against defects in materials and workmanship.
Fusion 8100: User Manual What is not covered by this warranty? This warranty does not apply: (i) to damage caused by use with products not manufactured by Warrantor, where the non-Warrantor product is the cause of the damage; (ii) to damage caused by service or maintenance performed by anyone who is not a representative of Warrantor; (iii) to damage caused by accident, abuse, misuse, flood, fire, earthquake or other external causes; (iv) to a product or part that has been modified after its retail purchase,
Fusion 8100: User Manual Manufactured under license under U.S. Patent Nos: 5,956,674; 5,974,380; 6,226,616; 6,487,535; 7,212,872; 7,333,929; 7,392,195; 7,272,567 & other U.S. and worldwide patents issued & pending. DTS-HD, the Symbol, & DTS-HD and the Symbol together are registered trademarks & DTS-HD Master Audio is a trademark of DTS, Inc. Product includes software. © DTS, Inc. All Rights Reserved. This product is manufactured under license from Dolby Laboratories.
Notes