User Guide

ManualsBrandsEMG ManualsElectric Guitar PartsEMG MF Marty Friedman Guitar Pickup Set, Brushed Black Chrome

.390

(10)

(6)

(8)

.235

.310

INSTALLATION INFORMATION

EMG MODEL: MARTY FRIEDMAN - MF SET

Warranty

All EMG Pickups and accessories are warranted for a period of two years. This warranty does not cover failure due to improper installation, abuse or damage. If

upon examination the pickup is determined to be defective, a replacement will be made. Warranty replacement products are covered by this same warranty. This

warranty covers only those pickups and accessories sold by authorized EMG Dealers. This warranty is not transferable.

BOX 4394

NTA ROSA, CA

402 USA

P (707) 525-9941

F (707) 575-7046

GPICKUPS.COM

0230-0322rB

(1) Wired in Series

(2) Loaded with 500K Volume and Tone with a 20’ (6M) cable

(3) Loaded with 1 MegOhm / 47pf

SPECIFICATIONS: MODEL:

MF-N5 (NECK) MF-B5 (BRIDGE)

Logo Color Gold Gold

Magnet Type Alnico 5 Alnico 5

Gauss Strength 275 275

Inductance (Henries) (1) 4.3 8.58

DC Resistance (kOhm) 7.55 16.2

Q .44 .39

Resonant Frequency (KHz) (2) 3.00 2.25

Resonant Frequency (KHz) (3) 4.54 3.39

Impedance at Resonance (kOhm) (2) 81 121

Installation notes:

All EMG-Passive Pickups are compatible with each other. The connector system is an easy method of installation, avoiding the need to solder.

EMG Accessory Circuits like the VLPF, EXG, SPC or RPC Controls can be added to any EMG Passive System, all EMG Accessory circuits have

buffered inputs and can be used on either passive or active pickups.

SPECIAL NOTE: The Red Wire of the HZ Pickup is NOT for battery power, it is a coil wire.

OUTPUT CABLE 6” (15cm)

4 CONNECT CABLES 5.5” (14cm)

BRIDGE GROUND WIRE 6” (15cm)

PICKUP CABLES 15” (30cm)

B245

2.75

1.50

3.09

3/48 MOUNTING HOLES

.900

.725 (18.4)

(69.8)

(38.1)

(22.8)

(78.5)

WHITE GREEN

RED

BLACK

COIL 2

SCREW BOBBIN

STUD BOBBIN

FINGERBOARD PICKUP

BRIDGE PICKUP

BLACK RED

GREEN

WHITE

STUD BOBBIN

SCREW BOBBIN

COIL 1

COIL 2

EMG COIL WIRING

2 VOLUME CONTROLS (500K)

2 TONE CONTROSL (500K)

ADJUSTMENT

SCREWS & SPRINGS

MONO OUTPUT

JACK

BRIDGE GROUND

CONNECTOR

2 PICKUP IN/ OUT

BATTERY BUSS

.39 (9.9) TYP

Included IN THE MF SET:

Summary of content (4 pages)

PAGE 1
2.75 (69.8) .39 (9.9) TYP 0230-0322rB 1.50 (38.1) PO BOX 4394 SANTA ROSA, CA 95402 USA 3.09 (78.5) 3/48 MOUNTING HOLES P (707) 525-9941 F (707) 575-7046 EMGPICKUPS.COM INSTALLATION INFORMATION EMG MODEL: MARTY FRIEDMAN - MF SET SPECIFICATIONS: MODEL: Logo Color Magnet Type Gauss Strength Inductance (Henries) (1) DC Resistance (kOhm) Q Resonant Frequency (KHz) (2) Resonant Frequency (KHz) (3) Impedance at Resonance (kOhm) (2) MF-N5 (NECK) Gold Alnico 5 275 4.3 7.55 .44 3.00 4.
PAGE 2
Installation Instructions: EMG Models: MARTY FRIEDMAN MF - SET EMG-HZ Wire Order: Pin 1 Green (GRN) Pin 2 White (WHT) Pin 3 Braid (GND) Pin 4 Red (RED) Pin 5 Black (BLK) Diagram #1 General Notes: Every attempt has been made to make this a solderless installation. There are some instances where this is not possible; 1) If your instrument uses the long panel output jack, soldering will be required 2) Instruments with two pickups may need soldering to the selection switch in some installations.
PAGE 3
Installation Instructions: EMG Models: MARTY FRIEDMAN - MF SET ****Tips and Tricks**** Start your installation by: 1) Remove the strings 2) Remove any existing Pickups and controls (remember the order and function of each control) 3) Determine a good spot for the Pickup Buss and make sure the cable or wires from the selection switch will reach the Pickup Buss, 4) Install the EMG Volume and Tone Controls and tighten them in.
PAGE 4
GROUND OUTPUT NECK P/U MASTER TONE B160A EMG T OUTPUT 250K 500K TONE BRIDGE P/U S OUTPUT CABLE NK VOLUME B159A 250K 500K VOLUME BR VOLUME B159A EMG VOLUME 250K Diagram #8 2 Pickups Toggle Style Switch Volume each Pickup (Volumes are independent) Master Tone FROM BRIDGE PICKUP EMG FROM NECK PICKUP 6 5 4 3 2 1 TO STRING GROUND SEE DIAGRAM #5 2 Pickups / Toggle Select Switch / 2 Volumes and 2 Tones) Refer to Diagram #9 1) Install the Pickups and route the cables to the control cavity.