Installation Touch Wi-Fi Thermostat 1
Table of contents COMPATIBILITY.................................................................4 WHAT’S IN THE BOX......................................................6 WHAT YOU’LL NEED....................................................... 7 BEFORE YOU BEGIN.......................................................8 INSTALLATION OVERVIEW.......................................10 WARNINGS........................................................................
Need some help? Visit sensicomfort.com/support for around-theclock access to support articles, instructional downloads and comprehensive support videos. Our highly-trained Sensi Support Team is available seven days a week. 1.888.605.7131 support@sensicomfort.com You’re just a few steps away from complete comfort control. Never installed a thermostat before? We’ve got you covered. Sensi™ Touch Wi-Fi® Thermostat was designed for a quick and easy DIY installation.
Compatibility Sensi thermostat is truly universal. Not only does it work with the HVAC equipment in most homes, but it also works with most mobile devices and smart home platforms. Check out the information below, to make sure Sensi thermostat will work for you: MOBILE DEVICE COMPATIBILITY OPERATING SYSTEM COMPATIBILITY iOS 10.
HVAC SYSTEM COMPATIBILITY SYSTEM TYPE COMPATIBILITY MODIFICATIONS Conventional heating and cooling • Gas furnace • Air conditioner • Electric furnace • Boiler Yes Requires a common wire (c-wire) Heat only • Gas furnace • Electric furnace • Boiler Yes Requires a common wire (c-wire) Cool only • Air conditioner Yes Requires a common wire (c-wire) Heat pump Yes Requires a common wire (c-wire) Communicating proprietary systems No Needs standard HVAC wiring Line voltage No Requires low voltag
What’s in the box? • Sensi Thermostat • Screws and Anchors • Wire Labels • Sensi password (found on the back of the Welcome Guide) XXX-XX-XXX 6
Here’s what you’ll need.
Download the Sensi app before you begin. This document is not meant to be used independently or to replace the step-by-step installation procedure found only in the Sensi app. The app is required for installation to ensure proper configuration and enable Wi-Fi control of your thermostat. The free Sensi mobile app is available on the App Store ™ and Google Play ™. Simply search for “Sensi” and download to your device to get started. All system types require a common wire (c-wire).
Installation Overview CREATE YOUR ACCOUNT. Open the Sensi app on your device and follow the prompts to create an account, using a valid email address. Your Sensi account can only be linked to one email address, but you can share your account information across devices so your whole family can have access. INSTALL YOUR THERMOSTAT. The Sensi app will walk you through removing your old thermostat from the wall, labeling your existing wires and installing your new Sensi thermostat. CONNECT TO WI-FI.
Installing Your Thermostat Turn off the power to your heating and air conditioning system by using your fuse box or the switch next to your furnace. WARNING: Confirm power is off before proceeding. To check, change the temperature on your thermostat. If your system turns on, it still has power.
REMOVE EXISTING THERMOSTAT COVER Remove the thermostat cover by using a screwdriver or by pushing the pressure latch. Some covers will detach easily, while others may need to be released with a screwdriver. WARNING: Do not remove your wires yet—this will be done in a later step.
TAKE A PHOTO OF YOUR WIRING Using your phone or digital camera, take a photo of your existing thermostat wiring in case you need to reference it later.
REMOVE ANY JUMPER WIRES If you see a jumper wire, remove it. Your new Sensi thermostat has the jumper wire built in. Leave all other wires connected to the thermostat.
LABEL YOUR WIRES Carefully label your wires by removing one wire at a time from the terminal and applying the corresponding wire label sticker to it. Your labels may not match - that’s okay! For example, if you have a W wire, you will apply a W/E sticker. Use the chart on the next page to find the correct wire label to use with each wire.
Old thermostat Sensi™ thermostat G wall G wall R, 5, R5, RC, or RH wall RC wall W, 4, W1 wall wall W2 W-U wall W2 wall Y, Y1 wall Y wall Y2 wall Y2/* wall O, B, O/B wall wall L, F wall L wall X, C wall C W/E wall O/B * Two transformer systems (separate RC and RH wires), clip internal jumper located on back of Sensi above battery compartment. ** L abel B as C only if the old thermostat als had a wire in O. If there is no wire on O-label the wire B.
REMOVE EXISTING BASE Using a screwdriver, remove the thermostat base from the wall. TIP: Wrap your wires around a pencil to keep them from falling back into the wall.
INSTALL SENSI BASE Mount the Sensi base using the supplied screws, drilling new holes and inserting wall anchors, if necessary. Carefully pull your wires through the center opening. A convenient terminal light is located on the thermostat base to help light your installation and navigate the process with ease. C G W/E Screws Install New Thermostat Base (Sensi 2.
CONNECT THE WIRES Insert each labeled wire into the corresponding easy-click terminal on the base. Just press the paddle underneath the terminal and insert the wire into the opening. To test the connection, give the wire a gentle tug.
TURN OFF LIGHT AND ATTACH COVER Turn off the terminal light on the thermostat base and securely attach the thermostat cover.
TURN ON POWER Turn on the power to the heating and air conditioning system at the furnace or fuse box.
CONFIGURE THE THERMOSTAT After installation, configure the thermostat to the appropriate system type. Press “Menu” on the thermostat and refer to these menu options as needed: Thermostat 2.
CONFIGURATION MENU ITEMS REFERENCE No.
CONNECT TO WI-FI On your Sensi thermostat, tap the Menu button in the top-left corner. Once on the Menu Options screen, select “Wi-Fi”. Then, tap “Connect to a new network.” For Apple HomeKit users: You may continue your setup in the Home app included with iOS 10 or in the Sensi app, available from the Apple App Store. For Android users: You may continue connecting your thermostat in the Sensi app, available from the Google Play Store.
Warnings INSTALLER INFORMATION FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY BEFORE INSTALLING OR OPERATING THIS CONTROL COULD CAUSE PERSONAL INJURY AND/OR PROPERTY DAMAGE. WARNING: OUT OF PHASE TRANSFORMERS On two transformer systems, the transformers MUST be in phase. Measure the voltage across RC and RH. If more than 12 Volts AC is present between RC and RH, then the transformers are NOT in phase.
To prevent electrical shock and/or equipment damage, disconnect electric power to system at main circuit breaker box until installation is complete. CAUTION: E5 Alert If “Call For Service” is displayed on your Sensi thermostat, and E4 or E5 appears where the room temperature should be displayed or the backlight is flashing, please call our support team immediately at 888.605.7131 ATTENTION: MERCURY NOTICE This product does not contain mercury.
www.sensicomfort.com The Emerson logo is a trademark and service mark and the Sensi logo is a trademark of Emerson Electric Co.