MODEL: EBTC08RE1T EBTC10RE1T EBTC12RE1T EBTC12RE2T EBTE14RRDT THRU-THE-WALL AIR CONDITIONER EBTC10RE2T EBTC12RD2T
INTRODUCTION IMPORTANT SAFETY INSTRUCTION ...........................................................................1 ELECTRICAL REQUIREMENTS ................................................................................... 2 PACKING LIST ............................................................................................................3 INSTALLATION & ASSEMBLY INSTRUCTIONS ..............................................................4 USING YOUR AIR CONDITIONER ................................
1
8K/10K/12K/14K Cooling 8K Cooling & Heating 2 10K/12K/14K Cooling & Heating
° ² × ° ¸ ½ ¼ þ ± í IMAGE or PAPT QUANTITY Through-The-Wall Air Conditioner 1 Remote Controll 1 Trim Frame 1 (Left&Right legs) 2 Trim Frame 2 (Top&Bottom legs) 2 Grille Aluminum 1 Rear plastic net 1 1/2" Long Hex-head Screw 4 Grouding wire with tooth washer 1 Dimension PAPT QUANTITY 1’’x3/4’’x14’’ Seal sponge 2 1’’x3/8’’x14’’ Seal sponge 2 1’’x3/8’’x25’’ Seal sponge 3 1’’x1 1/2’’x25’’ Seal sponge 3 1’’x1 1/2’’x14’’ Seal sponge 2 1’’x1 1/2’’x84’’ Seal sponge 1 3 3/ 4
Universal Wall-Sleeve Dimensions 1. Identify the wall-sleeve brand for your preparing, from the below chart.
NOTE • This units increased performance characteristics is the result of having two rear intakes. • It is very important that these installation instructions are followed so your unit can operate at maximum efficiency. • If there is an existing sleeve and rear grille, please check whether the dimension is suitable or not, otherwise replace them. Existing Frigidaire sleeves may have older single sided intake grilles, as below pictures. 1.
Direct Unit Mounting In case where the dual intake grille cannot be mounted directly to the sleeve it is desirable to attach the grille to the back of the TTW unit to the hole predrilled in the unit. 1. Attach the 2 seals(1''x3/8''x14''), as Fig. 1. 2. Position the grille over the rear of the unit making sure that: a.The double set of screw holes are at the bottom. b.The intake fins on either side are pointed away from the unit. 3. Align the top of the grille with the top of the unit.
Seal Installation 1. 1''x3/8''x25'' long seal in the center at the top of the sleeve. Remove the back paper and press into position. 2. 1''x3/8''x14'' seals to the left and right sides of the sleeve. 3. Cut 1''x3/8''x25'' long seals to 14'' long each and attach to the vertical sections of the grille as shown. 4. 1/2''x3 1/2''x1 1/2'' centering blocks one on each side wall. Place in center of side wall with the tapered end facing the opening. 5. Gently slide unit into sleeve. Ground Wire Installation 1.
Insert the unit with the seal into the sleeve pushing it all the way to rear making sure the seal are against the rear grille. The seals are necessary to reduce recirculation of hot air into the intakes which would reduce system performance. An option is to purchase 3/4'' diamond cut aluminum grille and cut it to fit inside the sleeve. Secure it with screws. Attach the dual intake grill directly to the back of the unit.
Cool Mode: The cooling function allows the air conditioner to cool the room and at the same time reduces Air humidify. Press the MODE button to activate the cooling function. To optimize the function of the air conditioner, adjust the temperature and the speed by pressing the button indicated. Dry Mode: This function reduces the humidity of the air to make the room more comfortable. Press MODE button to set the DRY mode. An automatic function of alternating cooling cycles and air fan is activated.
10. Directional Louvers: To direct the airflow, 6. Eco Button: When the unit is in ECO mode, the horizontal wheel to control the horizontal direction, light will turn on. In ECO mode, the unit will air deflector to control the vertical direction. turn-off once the room is cooled to the user set temperature. The fan will also be off at this point. The unit will turn back on when the room temperature rises above the user set temperature.
1 5. Timer: Use these buttons on the control panel and remote to set the Timer. Timer Off: The timed stop is programmed by pressing TIMER button. Set the rest time by pressing the button or until the rest time displayed is to your demand then press TIMER button again. Timer On: When the unit is off, press TIMER button at the first time, set the temperature with pressing the button or . Press TIMER button at the second time, set the rest time with pressing the button or .
FIG.21 FIG.
12
For any questions or Technical Support, Please Call Customer Service: 1-844-801-8880 13
