User's Manual

ManualsBrandsEmerson Appliance Controls ManualsElectronicsRF Transceiver for Remote Control of Spa Control System

Page 55

J-400 Series

4. With the “Set Month” highlighted

(Figure G), use the Left or Right

button n the Quad keypad to scroll

through selection. Once the correct

month is displayed, press the Down

button to enable the day selection.

5. With the “Set Day” highlighted

(Figure H), press the Left or Right

button on the Quad keypad to scroll

through selection. Once the correct

day is displayed, press the Splash

button to save your changes. Press

button D to return to the Date and

Time Setting menu.

11.5 Setting the Time

1. Press the Down button on the Quad

keypad to access the “Time Setting”

(Figure I) submenus.

2. The screen will open with

“Set Clock” highlighted (Figure J).

Press either the Left or Right button

on the Quad Keypad to choose

either a 12-hour or 24-hour (military

time) display. Then press the Down

button to enable the hour selection.

3. With “Set Hour” highlighted

(Figure K), press the Left (decrease)

or Right (increase button on the

Quad keypad to scroll through the

selection. Once the correct hour is

displayed, press the Down button to

enable the minutes selection.

Note: If you are using a standard 12-

hour day, you will see the hour displayed as “1PM”. For the

24-hour period it will read “1300”.

Figure G

5 4 3

TIME

Select

Ye a r

Hour

Day

Press to Save

Set Month Jan

Figure H

TIME

Select

Ye a r

Month

Day

Press to Save

Set Day 02

Press to Enter

5 4 3

DATE & TIME

Select

Date Settings

Time Settings

Dec 22 2008

04:15PM

Figure I

Figure J

5 4 3

TIME

Select

ClockSet Clock 12h

Hour

Minutes

Press to Save

Figure K

5 4 3

TIME

Select

Clock

Hour

Minutes

Press to Save

Set Hour

1PM

Summary of content (20 pages)

PAGE 1
J-400 Series TIME 5 4 3 4. With the “Set Month” highlighted (Figure G), use the Left or Right button n the Quad keypad to scroll through selection. Once the correct month is displayed, press the Down button to enable the day selection. Year Hour Set Month Jan Day Press Figure G TIME Year Month Day Set Day Press Select 02 to Save Figure H DATE & TIME 5 4 3 11.5 Setting the Time 1. Press the Down button on the Quad keypad to access the “Time Setting” (Figure I) submenus. to Save 5 4 3 5.
PAGE 2
J-400 Series 4. With “Set Min.” highlighted (Figure L), press the Left (decrease) or Right (increase button on the Quad keypad to scroll through the selection. Once the correct minutes are displayed, press the Splash button to save your changes. Press button D to return to the Setting 1 Main Menu. TIME 5 4 3 Clock Hour Set Min. Minutes Press 02 Select to Save Figure L 11.6 Locking and Unlocking the Topside 1. From the “Date and Time” Menu (Figure M), press button C to access the Lock feature.
PAGE 3
J-400 Series 12.0 Programming Instructions for Setting 2 Menus The “Setting 2” screen allows you to program Heating, Primary Filter and Secondary Filter modes. 12.1 Programming Heating Cycles Your Jacuzzi spa is equipped with two modes of heating. An automatic mode called “Auto-Heating”, where the spa’s temperature is maintained at all times by the “Setpoint”. The second mode is called “Programmable”, where the spa will only activate the heater at set times programmed by you.
PAGE 4
J-400 Series 12.2 Auto-Heating Mode HEATING Auto-Heating mode is typically selected Auto-Heating by customers in cold climates where heat Programmable Select up times are extended due to lower ambient temperatures. In this mode, water temperature is regulated by the set Press to Save temperature which activates the heater Figure C automatically as needed. Note: If you elect to use Auto-Heating, you can skip this Section. Auto-Heating is the default spa setting. A 1.
PAGE 5
J-400 Series 2. From this menu (Figure D), you can set the days, times, and duration. With “Day Settings” highlighted press the Splash button on the Quad Keypad to confirm selection. PROGRAM A A Day Settings StartTime Duration Press Select to Enter Figure D 3. When you enter the submenu (Figure E), you can choose the day(s) you would like “Program A” to run for a heating cycle. Press the Up or Down button (on the Quad keypad) to scroll through and choose the days you would like the heater to activate.
PAGE 6
J-400 Series 8. Press the Splash button on the Quad keypad to save your changes and return to the Heating Menu. At this point you can program a Secondary Heating Mode (Program B) or to continue on to the Filtering programming (see Section12.5, page 62). B. Program B Heating Mode PROGRAMMABLE Program A 1. To program the Secondary Heating mode press the Down button on the Quad Keypad to highlight “Program B” (Figure H). Press the Splash button to enter the submenus for Program B. 2.
PAGE 7
J-400 Series 6. Once back to the “Program B” Main PROGRAM B Menu, press the Down button on the Day Settings Quad keypad to highlight “Start Time 1AM StartTime Select Time” (Figure K). Press the Left or Duration B Right button on the Quad Keypad to select the time you wish the spa to Press to Save run. Press the Down button on keypad to save setting. Figure K Note: If you are using a standard 12-hour day, you will see the hour displayed as “1PM”. For the 24-hour period it will read “1300”. 7.
PAGE 8
J-400 Series 12.5 Programming the Primary Filter Cycle 1. To program the Primary Filter cycle press button A (Figure A). This cycle is mainly used to alter the 24-hour running period of the circulation pump. (If you would like to leave the circulation pump as is, then skip this Section). Upon entering the Primary submenu the “Start Time” will be highlighted (Figure B). 2. Press the Left or Right button on the Quad keypad to choose the hour you want the circulation pump to start running.
PAGE 9
J-400 Series 12.6 Programming the Secondary Filter Cycle 1. To program the Secondary Filter cycle, press button C. This cycle will activate the main jet pump to run for additional filtration when programmed. If you choose not to use this feature, please skip this Section. 2. When you enter the Secondary Filter Cycle submenu, the “Day Settings” will be highlighted (Figure E). From this menu, you can set the say, time, and duration. Press the Splash button on the Quad keypad to confirm selection.
PAGE 10
J-400 Series 7. Now you will need to adjust the filter cycle “Duration” (Figure H). The duration range is from 0 (OFF) to 120 minutes. Press the Left or Right button on the Quad Keypad to make your adjustments in increments of 15 minutes. SECONDARY Day Settings StartTime Duration OFF Press Select to Save Figure G 8. Press the Splash button on the quad keypad to save selection. Then press button D several times to return to the main operation menu (page 32). 13.
PAGE 11
J-400 Series polishing bag filter and additional filter. The exclusive footwell “sweeper” suction fitting enhances filtration in the footwell area by creating a “swirling” water motion to maximize particle agitation and pickup. To ensure optimum performance, the 24-hour ProClear™ II skimming filter cartridge (A) must be cleaned every C three months and replaced once a year. The secondary ProClear™ Plus polishing filter bag (B) should be emptied A weekly and replaced every 3 months.
PAGE 12
J-400 Series 6. Clean the ProClear filter cartridges with a garden hose and high pressure nozzle. Rinse debris from the filter pleats beginning at the top and working your way downward. Continue, one section at a time until you have cleaned all debris from the filter pleats. When replacing the filter cartridge, make sure you remove the center cap and chemical dispenser for use with the new cartridge. Replacement filter cartridges may be purchased from your authorized Jacuzzi dealer. 13.
PAGE 13
J-400 Series 5. Pull the larger (rear) body outward as shown to open drain. 5. Open Drain 6. After the spa drains, perform steps 2-5 in reverse order to close the drain prior to refilling spa. After refilling, turn on power to the spa and follow the steps listed under “Spa Fill Up Procedures.” (page 15). Always fill your spa through both filter buckets. 13.
PAGE 14
J-400 Series against deterioration caused by UV rays from the sun. Never allow anyone to stand or sit on the cover, and avoid dragging it across rough surfaces. 13.7 Winterizing Your Jacuzzi spa is designed to automatically protect itself against freezing when operating properly. During periods of severe freezing temperatures, you should check periodically to be certain that the electrical supply to the spa has not been interrupted.
PAGE 15
J-400 Series Consult your Jacuzzi dealer if you have any questions regarding winter use or winterizing. 13.8 Restarting Your Spa in Cold Weather If you want to start up your spa after it has sat empty for a time in freezing temperatures, be aware that the water remaining in certain sections of the piping may still be frozen. This situation will block water flow preventing the spa from operating properly and possibly damaging the equipment.
PAGE 16
J-400 Series sanitizers used to date. Many other additives are available for your spa. Some are necessary to compensate for out-of-balance water, some aid in cosmetic water treatment and others simply alter the fell or smell of the water. Your authorized jacuzzi dealer can advise you on the use of these additives. IMPORTANT: Do not use chlorine tablets (trichlor) in your spa. This chemical can have an extremely corrosive effect on certain materials in the spa.
PAGE 17
J-400 Series MESSAGE MEANING Overheat protection: (Heater is deactivated, filter/ OVERHEAT circulation pump is activated). Water temperature is above acceptable limits. Do not enter the water! Remove spa cover to speed cooling. See “Water Is Too Hot” on page 75. If condition persists, contact your authorized dealer or authorized service center.
PAGE 18
J-400 Series SENSOR SHORT, TEMP SENSOR Shorted sensor: The temperature sensor is not functional. Heater is disabled. This must be repaired only by a qualified authorized service organization or service technician. SENSOR OPEN, HI-LIMIT SENSOR Open sensor: The hi-limit temperature sensor is not functional. Heater is disabled. This must be repaired only by a qualified authorized service organization or service technician.
PAGE 19
J-400 Series 3. Feature not installed (Exterior lights) This message will appear when a user tries to activate the exterior lights and they are not installed (see Figure C). To clear the message press button D to return to Main Menu. EXTERIOR Feature not installed Please contact your local dealer to upgrade Figure C 4. Clear Settings 2 Programs This message will appear when you choose to reset all settings 2 menu settings back to factory defaults (Figure D).
PAGE 20
J-400 Series 16.0 Troubleshooting Procedures In the unlikely event your spa is not working the way you believe it should, please first review all the installation and operating instructions in this manual and check the message on the panel display; second, if you are still not satisfied it is working properly, please follow the appropriate troubleshooting instructions. PROBLEM PROCEDURE NONE OF THE COMPONENTS OPERATE (i.e. pump light) Check the control panel lights. 1.