Product specifications

ManualsBrandsElumenati ManualsProjectorOmniFocus 200 Series

www.elumenati.com

i nfo@elumenati.com

Elumenati OmniFocus 200 Series

Installation and Operation Guide

Last updated: November 2012

This document applies to the OmniFocus 3020 and 30210 sold after January 2013.

For all previous 200 Series products please refer to the “OmniFocus 200 Series

pre2013” manual.

For brevity, we refer to the 200 Series throughout. Differences are noted where applicable.

Elumenati OmniFocus 200 Series .................................................................................1

Installation and Operation Guide..................................................................................1

200 Series Overview...................................................................................................2

Introduction...........................................................................................................2

Equipment List.......................................................................................................2

200 Series Setup........................................................................................................3

Projector Connection...............................................................................................3

Lens Installation.....................................................................................................4

First Light..............................................................................................................5

Projector Settings Adjustment..................................................................................5

Stand Assembly (Optional)......................................................................................7

200 Series Information...............................................................................................8

Maintenance..........................................................................................................8

Troubleshooting......................................................................................................8

Product Support.....................................................................................................8

200 Series Product Specifications.................................................................................9

Immersive Projection Design - www.elumenati.com

Elumenati, GeoDome OmniFocus and OmniMap are all trademarks of The Elumenati LLC.

Summary of content (10 pages)

PAGE 1
www.elumenati.com info@elumenati.com Elumenati OmniFocus 200 Series Installation and Operation Guide Last updated: November 2012 This document applies to the OmniFocus 3020 and 30210 sold after January 2013. For all previous 200 Series products please refer to the “OmniFocus 200 Series pre2013” manual. For brevity, we refer to the 200 Series throughout. Differences are noted where applicable. Elumenati OmniFocus 200 Series .................................................................................
PAGE 2
OmniFocus 200 Series Installation and Operation Guide 200 Series Overview Introduction This guide covers the installation and operation of the 200 Series projection system, as well as an overview of operation. Please read through this entire guide before following the instructions. This will familiarize you with the process of setup for the 200 Series Projection System. The 200 Series is a variation of the 200 Series using the same lens but with a different projector and mounting system. Equipment List 1.
PAGE 3
OmniFocus 200 Series Installation and Operation Guide 200 Series Setup The 200 Series is shipped with the adjustable lens mount already installed and aligned to the default setting (truncated or fulldome). The lens is removed from the mount and housed separately inside the case. The following describes the setup procedure. Projector Connection Before attaching the Elumenati lens, set up and/or install the projector and connect the projector to the video source.
PAGE 4
OmniFocus 200 Series Installation and Operation Guide 4. The graphics card of your computer should detect the projector. Adjust desktop settings to enable the second monitor (extended displays mode). Default resolution is 1920 x 1200. It may be helpful to use either the truncated or fulldome Elumenati alignment image as your desktop background. Again use desktop settings to change your background making certain that the image is displayed 1:1 and not stretched or tiled. 5.
PAGE 5
OmniFocus 200 Series Installation and Operation Guide First Light 1. Turn on projector. 2. Remove the large lens cap by pulling it off. Do not attempt to unscrew the lens cap. ● Take care not to scratch the fisheye element/lens while removing and replacing cap. 3. You should see the projector startup screen. 4. Adjust focus using either the projector control panel or remote control. (Fig. 3 above) ● Focus to “good enough”. Final focus is done after setup is complete.
PAGE 6
OmniFocus 200 Series Installation and Operation Guide (Fig. 7) Nominal Zoom and Lens Shift settings for truncated projection. 2. Zoom and Lens Shift are interdependent, they must be adjusted together. It is best to use the Elumenati supplied alignment pattern described above during these adjustments. ● For Truncated projection • Adjust Zoom to its narrowest setting (Fig. 7). • Then adjust the physical height of the projector so that the outer circle of the alignment pattern (Fig.
PAGE 7
OmniFocus 200 Series Installation and Operation Guide Stand Assembly (Optional) The stand is shipped collapsed flat. 1. Loosen the tilt knobs and raise the vertical section to 90°. Tighten the knobs. 2. Loosen the 6 bolts that join the vertical section to the base (3 on either side) and slide the vertical section in about 1/3 of the base length. Tighten the bolts. Your stand should resemble the image in Fig. 9. 3. The extruded aluminum framing on the 200 Series project allows for multiple mounting options.
PAGE 8
OmniFocus 200 Series Installation and Operation Guide 200 Series Information This section contains product specifications, troubleshooting tips, and support information. Maintenance Lens Care The bright light of the projector exaggerates the amount of dust on the lens surface. Dust has very little effect on picture quality and can be blown off or wiped away with a cloth. We recommend cleaning the lens ONLY if there are fingerprints or similar on the lens. To clean: 1.
PAGE 9
OmniFocus 200 Series Installation and Operation Guide 200 Series Product Specifications OMNIFOCUS PROJECTION DIMENSIONS • Infinite depth of focus • Weight: 22.0 lbs / 10.
PAGE 10
OmniFocus 200 Series Installation and Operation Guide (Fig. 11) 30200 straight lens minimizes interference in traditional planetarium installations. (Fig. 12) 30210 features a folded lens minimizing the overall fm factor. Immersive Projection Design - www.elumenati.com Elumenati, GeoDome OmniFocus and OmniMap are all trademarks of The Elumenati LLC.