User's Manual

Elpas Personal Safety Bracelet
P/Ns: 5-WTD40100-0, 5-WTD40101-0, 5-WTD41100-0 and 5-WTD41101-0
User Guide
www.elpas.com
Page 1 of 3
V2/Sept 2012
Introduction
The Personal Safety Bracelet is a wrist worn Active RFID Tag that provides around-
the-clock monitoring of medical patients and assisted living care residents who
require added safety.
The bracelet bundles triple-tech Real-Time Location System (RTLS) technologies to
deliver precise real-time positioning data so that a host RTLS safety application or an
integrated physical security platform can track the whereabouts of the individual
anywhere within the facility.
The bracelet features a large duress call button designed especially for senior
citizens. Pressing the button causes the tag to transmit positioning data that identifies
the person requiring assistance and the precise building location of the involving
medical or safety incident for speedier and more effective response efforts.
The bracelet also enables immediate near-exit location awareness for administering
patient/staff escort procedures and for preventing unauthorized transfers into or out of
protected building areas.
It is important that you understand, and follow the instructions in this document.
Should you have any questions, please contact your Elpas support representative
before proceeding with the installation, operation or maintenance of these products.
Product Specifications
Transmission Rates in LF Zones
Moving Bracelet
LF Response Time: Onboard LF receiver
polls every 0.6 sec to check if the bracelet is
in a LF zone.
Transmission Rate: Bursts of 6 IR/RF
supervision transmissions (each
transmission about 2ms in duration), 400ms
apart. If the bracelet stays in a LF zone, then
repeated at 2 seconds intervals.
Transmitted Message Type: IR/RF Data
Message includes ID code of LF Exciter.
Motion bit, M=1.
Motionless Bracelet
LF Response Time: Onboard LF receiver
polls every 15 seconds to check if the badge
is in a LF zone.
Transmission Rate: 6 IR/RF supervision
transmissions (each transmission about 2ms
in duration), 0.4 seconds apart: If the bracelet
stays in a LF zone, then repeated at 15
second intervals.
Transmitted Message Type: IR/RF Data
Message includes ID code of LF Exciter.
Motion bit, M=0
Signaling Technologies
RF (433MHz) IR (800nm) LF (125KHz)
RF (Motion/Stationary)
Supervision messages every 10 seconds / 60 seconds
IR (Motion/Stationary)
Supervision messages every 10 seconds / 60 seconds
RF Under LF
6 IR/RF transmissions (each @ 2ms in duration), 0.5secs apart;
every 2 secs after 10 mins returns to 10 secs when in motion
Supervised Events
Button Press/Release
Motion/Stationary
Low Battery
3 RF/IR transmissions (each @2ms in duration), 400ms apart
Power Source
3.0V/560mAH lithium battery, CR 2450
Battery Life
12-36 months depending upon usage
LED Indicator
Low Battery, Button Press, LF Field
Badge ID
Factory-Programmed ID
Housing
IP65, Nylon Plastic
Weight
35 grams (1.23 ounces)
Dimensions (H x W x D)
46.9 x 41.0 x18.9mm (1.84 x 1.61 x 0.74 inches)
Operating Environment
Temp: 0°C to 50° (0°F to 122°F)
Humidity: 100% non-condensing
Management Software
Eiris 4.6 (or higher)/Eiris Configurator 4.8 (or higher)
ELC Programmer V2.0
Standards
IC, FCC & CE compliant
Warranty
1 year limited warranty (excluding battery)
Product offerings and specifications are subject to change without notice.
Not all products include all features.
Compatible Accessories
Part Number
Description
5-PBA90003
3.0V/560mAH lithium battery, CR 2450 (20 pcs)
5-WTD09001
Standard Wristband (set of 5)
5-WTD09003
Hospital Band Adapters (set of 5)
*5-PB063011
Disposable Clincher Wristband (set of 50)
*5-WTA90007
Reusable Medical Grade Wristband with Lock Pin (5 pcs)
5-500130
Lock Pin Removal Magnet
*Requires Hospital Band Adapters for use with Bracelet P/Ns 5-WTD40000-0 & 5-WTD41000-0.