Installation Sheet

ManualsBrandsElkay ManualsCoolersWall Mounted Cooler Hands-Free Non-Filtered Refrigerated in Light Gray Granite Color

Page 1

EZO8*1H EZO8*2H EZO8*3H EZOD*1H

1000002686 (Rev. A - 07/18)

EZO™ La Barrera de la serie Liberta Agua Coolers

EZO™ Coolers d’Eau de Barrière-Libère de feuilleton

EZO™ Series Sensor-Operated Water Coolers

INSTALLATION & USE MANUAL

Model EZO8L

Manual de instalación y uso

Manuel d’installation et utilisation

Summary of content (7 pages)

PAGE 1
EZO8*1H EZO8*2H EZO8*3H EZOD*1H INSTALLATION & USE MANUAL Manual de instalación y uso Manuel d’installation et utilisation EZO™ Series Sensor-Operated Water Coolers EZO™ La Barrera de la serie Liberta Agua Coolers EZO™ Coolers d’Eau de Barrière-Libère de feuilleton Model EZO8L Page 1 1000002686 (Rev.
PAGE 2
EZO8*1H EZO8*2H EZO8*3H EZOD*1H Note: Danger! Electrical shock hazard. Disconnect power before servicing unit. Nota: peligro! Peligro de descarga eléctrica. Desconecte antes de reparar la unidad Remarque : Danger ! Risque de choc électrique. Débrancher avant de réparer l’appareil.
PAGE 3
D Page 3 2" 51mm 3 7/8" 98mm 5 3/4" 146mm 7" 178mm 28 13/16" 732mm 13 15/16" 354mm A E 2" 51mm 32 7/8" 835mm ORIFICE HEIGHT 27" 686mm ADA REQUIREMENT 31 5/16" 796mm RIM HEIGHT C 5 7/8" 150mm 3" 77mm 12 1/2" 318mm 2" 51mm 8 1/16" 205mm HANGER BRACKET **LES NOUVELLES INSTALLATIONS DOIVENT EMPLOYER LES INTERRUPTEURS DE CIRCUIT MOULUS DE DÉFAUT (GFCI) LEGEND/LEYENDA/LÉGENDE A = RECOMMENDED WATER SUPPLY LOCATION 3/8” O.D.
PAGE 4
EZO8*1H HANGER BRACKETS INSTALLATION 1) Remove hanger brackets fastened to back of cooler by removing one (1) screw. 2) Mount the hanger brackets as shown in Figure 2. NOTE: Hanger Bracket MUST be supported securely. Add fixture support carrier if wall will not provide adequate support. Anchor hanger securely to wall using all six (6) 1/4 in. dia. mounting holes. INSTALLATION OF COOLER 3) Hang the cooler on the hanger bracket.
PAGE 5
EZO8*1H EZO8*2H EZO8*3H EZOD*1H Service Instructions Lower and Upper Shroud 11 To access the refrigeration system and plumbing connections, remove four screws from bottom of cooler to remove the lower shroud. To remove the upper shroud for access to the pushbars, regulator, solenoid valve or other components located in the top of the unit, remove lower shroud, disconnect drain, remove four screws from tabs along lower edge of upper shroud, unplug two wires and water tube.
PAGE 6
EZO8*1H EZO8*2H EZO8*3H EZOD*1H SENSOR RANGE ADJUSTMENT: The electronic sensor used in this cooler is factory pre-set for a “visual” range of 36 inches (914 mm). If actual range varies greatly from this or a different setting is desired, follow the range adjustment procedure below: - Using a small tip screwdriver, locate range adjustment screw through the small hole between the sensor lenses (See Page 1.) Turn this screw clockwise to increase range and counterclockwise to decrease range (See Fig. 3).
PAGE 7
EZO8*1H EZO8*2H EZO8*3H EZOD*1H 115V PARTS LIST/ 115V LISTA DE PIEZAS/ 115V LISTE DES PIÈCES ITEM NO. PART NO.