Installation and Assembly

ManualsBrandsElkay ManualsDrinking FountainsWall Mount Bottle Filling Station

Page 1 98770C (Rev. A - 6/11)

LVRCGRN8WS*1B LVRCGRNTL8WS*1B

LVRCGRN8WS Factory Prep

EZH2O Bottle Filling Station and Cooler

LVRCGRN8WS Bottle Fillers are among the easiest to install on the market today.

To insure you install these models easily and correctly, PLEASE READ THESE

SIMPLE INSTRUCTIONS BEFORE STARTING THE INSTALLATION. CHECK

YOUR INSTALLATION FOR COMPLIANCE WITH PLUMBING, ELECTRICAL, AND

OTHER APPLICABLE CODES. After installation, leave these instructions with the

Fountain for future reference.

IMPORTANT

THIS IS AN INDOOR APPLICATION ONLY.

ALL SERVICE TO BE PERFORMED BY AN

AUTHORIZED SERVICE PERSON.

IMPORTANT! INSTALLER PLEASE NOTE.

THE GROUNDING OF ELECTRICAL EQUIPMENT SUCH AS TELEPHONE, COMPUTERS, ETC. TO WATER LINES

IS A COMMON PROCEDURE. THIS GROUNDING MAY BE IN THE BUILDING OR MAY OCCUR AWAY FROM THE

BUILDING. THIS GROUNDING CAN CAUSE ELECTRICAL FEEDBACK INTO A FOUNTAIN, CREATING AN ELEC-

TROLYSIS WHICH CAUSES A METALLIC TASTE OR AN INCREASE IN THE METAL CONTENT OF THE WATER.

THIS CONDITION IS AVOIDABLE BY USING THE PROPER MATERIALS AS INDICATED. ANY DRAIN FITTINGS

PROVIDED BY THE INSTALLER SHOULD BE MADE OF PLASTIC TO ELECTRICALLY ISOLATE THE FOUNTAIN

FROM THE BUILDING PLUMBING SYSTEM. WE SUGGEST THAT THE BOTTLE FILLING STATION AND WATER

COOLER BE PROTECTED BY A GROUND FAULT CIRCUIT INTERRUPTER (GFCI).

INSTALLER

TOOLS REQUIRED

BUT NOT PROVIDED:

SAFETY GLASSES

GLOVES

ELECTRIC DRILL

3/4” WRENCH OR CRECENT WRENCH

5/16” NUT DRIVER

UTILITY KNIFE

TAPE MEASURE

PENCIL

CENTER PUNCH

1/2” SOCKET & RATCHET WRENCH

5/32” ALLEN WRENCH

Installation/Care/Use Manual

Summary of content (7 pages)

PAGE 1
LVRCGRN8WS*1B LVRCGRNTL8WS*1B Installation/Care/Use Manual LVRCGRN8WS Factory Prep EZH2O Bottle Filling Station and Cooler IMPORTANT THIS IS AN INDOOR APPLICATION ONLY. ALL SERVICE TO BE PERFORMED BY AN AUTHORIZED SERVICE PERSON. TOOLS REQUIRED BUT NOT PROVIDED: SAFETY GLASSES GLOVES ELECTRIC DRILL 3/4” WRENCH OR CRECENT WRENCH 5/16” NUT DRIVER UTILITY KNIFE TAPE MEASURE PENCIL CENTER PUNCH 1/2” SOCKET & RATCHET WRENCH 5/32” ALLEN WRENCH IMPORTANT! INSTALLER PLEASE NOTE.
PAGE 2
98770C (Rev. A - 6/11) 51 9/16" 1310mm Page 2 Single Rough-In Fig.
PAGE 3
58 1/16" 1475mm 37 7/16" 951mm E Page 3 20 5/16" 516mm 5" 127mm 5 3/4" 146mm 2 7/16" 63mm 11/16" 18mm 4 9/16" 116mm 5 3/4" 146mm 7" 178mm FINISHED FLOOR 9 15/16" 252mm CL 17 7/8" 454mm B 1 3/8" 35mm 3 3/8" 86mm 4 1/2" 114mm 6 1/4" 159mm 3 1/2" 89mm 1 3/8" 35mm 5 3/4" 146mm 18 1/16" 459mm 15" 381mm CL D 5 3/4" 146mm 20 1/8" 511mm 18 3/4" 477mm 13 13/16" 351mm F A 1 3/8" 35mm E 25 1/8" 638mm 39 7/16" 1002mm ORIFICE HEIGHT * 27" 686mm 31 13/16" 809mm RIM HEIGHT 32 15/16" 837
PAGE 4
LVRCGRN8WS*1B LVRCGRNTL8WS*1B 7/16” BOLT HOLES FOR FASTENING UNIT TO WALL MOUNTING SCREWS TOP COVER UNIT CENTER LINE Fig. 3 Fig. 4 BOTTLE FILLER INSTALLATION 1) 2) 3) 4) Remove two (2) mounting screws with 5/32” allen wrench holding top cover to Bottle Filler (See FIG. 4). Remove top cover. Note do not discard mounting screws, they will be needed to reinstall top cover.. Remove wall mounting plate from Bottle Filler. Place Wall plate against wall on top of LVRC basin.
PAGE 5
LVRCGRN8WS*1B LVRCGRNTL8WS*1B BF6-BF7-BF8 PROGRAMS SETTING THE CONTROL BOARD VERIFY CONTROL BOARD SOFTWARE 1) To verify the software program of the control board the unit will need to be shut down and restarted. The chiller (if present) does not need to be shut down and restarted. 2) The units lower panel must be open to access the power cord and wall outlet. 3) Shut down the unit by unplugging the power cord from the wall outlet. 4) Restart the unit by plugging the power cord back into the wall outlet.
PAGE 6
LVRCGRN8WS*1B LVRCGRNTL8WS*1B BF9 PROGRAM SETTING THE CONTROL BOARD VERIFY CONTROL BOARD SOFTWARE 1) To verify the software program of the control board the unit will need to be shut down and restarted. The chiller (if present) does not need to be shut down and restarted. 2) The units lower panel must be open to access the power cord and wall outlet. 3) Shut down the unit by unplugging the power cord from the wall outlet. 4) Restart the unit by plugging the power cord back into the wall outlet.
PAGE 7
LVRCGRN8WS*1B LVRCGRNTL8WS*1B ® WATERSENTRY PLUS FILTER PARTS LIST (See Fig. 7) ITEM NO. PART NO. 1 2 3 4 5 6 7 51294C 70792C 70823C 70822C 51300C 70818C 28641C LISTA DE PIEZAS DEL FILTRO (Vea Fig. 7) LISTE DES PIÈCES DU FILTRE (Voir Fig. 7) DESCRIPCIÓN DESCRIPTION Ensamblado de la Cabeza del Filtro Tornillo #8-18 x .75 PH Accesorio - Supersello 3/8" (10mm) Accesorio - Supersello 1/4" (6 mm) Ensamblado del Filtro Codo - 3/8" (10 mm) Fijador Ens. de tête de filtre Vis #8-18 x .