Installation Sheet

ManualsBrandsElkay ManualsPopular CollectionsElkay Crosstown Stainless Steel Single Bowl Top Mount Sink with Glass Top

ECTGR SERIES TOP MOUNT STAINLESS

STEEL SINK

TOP MOUNT INSTALLATION

• READ THESE INSTRUCTIONS THOROUGHLY BEFORE YOU BEGIN.

DO NOT REMOVE PROTECTIVE PLASTIC ATTACHED TO GLASS

RIM UNTIL INSTALLATION IS COMPLETE.

ATTENTION INSTALLER:

1) ELKAY RECOMMENDS THAT SINK SHOULD BE INSTALLED BY A PROFESSIONAL

EXPERIENCED INSTALLER.

2) ELKAY IS NOT RESPONSIBLE FOR SINK AND COUNTERTOP IF DAMAGED DURING

INSTALLATION.

3) METAL EDGES MAY BE SHARP - USE CAUTION WHEN HANDLING.

4) FOLLOW ALL LOCAL PLUMBING AND BUILDING CODES.

5) INSPECT SINK FOR DAMAGE PRIOR TO BEGINNING INSTALLATION.

6) ELKAY CANNOT ASSUME ANY RESPONSIBILITY FOR FIXTURES IMPROPERLY INSTALLED.

STEP 1: COUNTERTOP OPENING

Carefully position template (enclosed) on the counter and

tape down.

Take into consideration adequate clearance for the

faucet, backsplash, and any accessories such as

soap/lotion dispenser.

The template includes the faucet hole locations, glass rim

perimeter and bowl cutouts. (Figure 1)

Carefully mark sink cutout and faucet hole locations.

+ +

1" R

Bowl Cutout

Figure 1

Glass Rim Outline

Cut countertop opening following the countertop manufacturer’s

recommended instructions (Figure 2).

Figure 2

Page 1 of 4

Summary of content (8 pages)

PAGE 1
ECTGR SERIES TOP MOUNT STAINLESS STEEL SINK TOP MOUNT INSTALLATION • READ THESE INSTRUCTIONS THOROUGHLY BEFORE YOU BEGIN. ATTENTION INSTALLER: 1) ELKAY RECOMMENDS THAT SINK SHOULD BE INSTALLED BY A PROFESSIONAL EXPERIENCED INSTALLER. 2) ELKAY IS NOT RESPONSIBLE FOR SINK AND COUNTERTOP IF DAMAGED DURING INSTALLATION. 3) METAL EDGES MAY BE SHARP - USE CAUTION WHEN HANDLING. 4) FOLLOW ALL LOCAL PLUMBING AND BUILDING CODES. 5) INSPECT SINK FOR DAMAGE PRIOR TO BEGINNING INSTALLATION.
PAGE 2
Test fit sink to make sure sink fits into opening and sink bowl flanges rest on countertop. Remove sink. Create a rabbet cut 0.090" deep x 0.75" wide around the sink opening (Figure 3). 0.75" 0.090" Figure 3 Test fit sink to make sure the glass rim is sitting on the counter (Figure 4). If the sink flange prevents the glass from sitting on the counter, increase the depth of the rabbet by 0.01" increments and test again.
PAGE 3
STEP 2: CLEANING AND CAULKING THE SINK Clean the underside of the glass rim, sink flange and sealing surface of countertop opening with denatured alcohol (Figure 6). Allow to air dry. Figure 6 Apply a high quality 3/8" wide continuous bead of black Kitchen & Bath Grade silicone to edge of glass rim (not furnished) (Figure 7). Figure 7 Add a 3/8" wide continuous bead of silicone to the rabbet cut, as well as faucet holes (Figure 8).
PAGE 4
Use and Care Hints Stainless Steel Finish Regular cleaning is important to maintain the appearance of your Elkay sink. Easy Cleaning Instructions Rinsing is the most important part of sink care. An Elkay stainless steel sink finish will retain its original bright appearance if the sink is rinsed thoroughly after each use. “Thorough” rinsing can be done by running the water throughout the sink for a few minutes after each use.
PAGE 5
fregaderos + grifos FREGADERO DE ACERO INOXIDABLE DE MONTAJE SUPERIOR, DE LA SERIE ECTGR INSTALACIÓN DE MONTAJE SUPERIOR • LEE ATENTAMENTE ESTAS INSTRUCCIONES ANTES DE COMENZAR. ATENCIÓN INSTALADOR: 1) ELKAY RECOMIENDA CONTRATAR A UN INSTALADOR PROFESIONAL CON EXPERIENCIA PARA MONTAR ESTE FREGADERO. 2) ELKAY NO ES RESPONSABLE POR DAÑOS AL FREGADERO NI AL MOSTRADOR DURANTE LA INSTALACIÓN. 3) LOS BORDES DE METAL PUEDEN ESTAR AFILADOS - TEN CUIDADO AL MANIPULARLOS.
PAGE 6
Prueba si el fregadero se ajusta en la abertura y las bridas del fregadero descansan sobre el mostrador. Retira el fregadero. Corte una ranura de 2.2 mm de profundidad x 19 mm de ancho alrededor de la abertura del fregadero (Figura 3). 0.75" 0.090" Figura 3 Prueba para asegurarte de que el borde de vidrio está asentado sobre el mostrador (Figura 4). Si la brida del fregadero evita que el vidrio descanse sobre el mostrador, aumenta la profundidad de las ranuras en 0.3 mm cada vez y prueba de nuevo.
PAGE 7
PASO 2: CÓMO LIMPIAR Y ENMASILLAR EL FREGADERO Limpia el lado inferior del borde de vidrio, la brida del fregadero y la superficie de la abertura del mostrador con alcohol desnaturalizado (Figura 6). Deja secar al aire. Figura 6 Aplica una franja continua de 9.5 mm de ancho de silicona de alta calidad para cocina y baño en el borde de vidrio (no incluido) (Figura 7). Figura 7 Agrega una franja continua de 9.5 mm de ancho de silicona a la ranura y a los orificios del grifo (Figura 8).
PAGE 8
Consejos de uso y mantenimiento Acabado en acero inoxidable Calidad del agua La limpieza regular es importante para mantener la apariencia de tu fregadero Elkay. Instrucciones para una limpieza fácil Enjuagar es la parte más importante del cuidado del fregadero. El acabado de un fregadero de acero inoxidable Elkay mantendrá su apariencia brillante original si el fregadero se enjuaga completamente después de cada uso.