Installation Instructions

ManualsBrandsElkay ManualsDrinking FountainsElkay Child ADA Wall Mount Single Level Slimline Fountain with Wall Plate, Freeze Protection and Access Panel

Page 1

98011C (Rev. J - 1/08)

ECDFPW314FP

Installation/Care/Use Manual

Soft Sides

™

Freeze Resistant Fountain

IMPORTANT! INSTALLER PLEASE NOTE.

THE GROUNDING OF ELECTRICAL EQUIPMENT SUCH AS TELEPHONE, COMPUTERS, ETC. TO

WATER LINES IS A COMMON PROCEDURE. THIS GROUNDING MAY BE IN THE BUILDING OR MAY

OCCUR AWAY FROM THE BUILDING. THIS GROUNDING CAN CAUSE ELECTRICAL FEEDBACK

INTO A FOUNTAIN, CREATING AN ELECTROLYSIS WHICH CAUSES A METALLIC TASTE OR AN

INCREASE IN THE METAL CONTENT OF THE WATER. THIS CONDITION IS AVOIDABLE BY USING

THE PROPER MATERIALS AS INDICATED. ANY DRAIN FITTINGS PROVIDED BY THE INSTALLER

SHOULD BE MADE OF PLASTIC TO ELECTRICALLY ISOLATE THE FOUNTAIN FROM THE BUILDING

PLUMBING SYSTEM.

IMPORTANT

ALL SERVICE TO BE PERFORMED BY AN AUTHORIZED SERVICE PERSON

To assure you install this model easily and correctly, PLEASE READ THESE SIMPLE

INSTRUCTIONS BEFORE STARTING THE INSTALLATION. CHECK YOUR

INSTALLATION FOR COMPLIANCE WITH PLUMBING, ELECTRICAL AND OTHER

APPLICABLE CODES. After installation, leave these instructions inside the fountain for

future reference. This Freeze Resistant Fountain is shipped in two separate cartons.

The second carton contains the Freeze Resistant Package LKFRB1 that is installed on

an interior heated wall. The interior space must maintain a minimum temperature of 50°

F (10° C). Refer to the Freeze Resistant Package for the rough-in dimensions for instal-

lation.

Installer

Summary of content (6 pages)

PAGE 1
ECDFPW314FP Installation/Care/Use Manual ™ Soft Sides Freeze Resistant Fountain Installer To assure you install this model easily and correctly, PLEASE READ THESE SIMPLE INSTRUCTIONS BEFORE STARTING THE INSTALLATION. CHECK YOUR INSTALLATION FOR COMPLIANCE WITH PLUMBING, ELECTRICAL AND OTHER APPLICABLE CODES. After installation, leave these instructions inside the fountain for future reference. This Freeze Resistant Fountain is shipped in two separate cartons.
PAGE 2
98011C (Rev. J - 1/08) Page 2 NOTE: REINFORCE THE WALL IN THE SHADED AREAS LEGEND A = RECOMMENDED WATER SUPPLY LOCATION. 3/8 O.D. UNPLATED COPPER TUBE CONNECT STUBBED 1-1/2" (38mm) FROM WALL. SHUT OFF BY OTHERS. B = RECOMMENDED LOCATION FOR WASTE OUTLET 1-1/4" O.D. DRAIN. MOUNTING BOLT AND ACCESS HOLE LAYOUT ECDFPW314FPC FIG.
PAGE 3
1. Wall should already be framed for the fountains using dimensions shown in Fig. 1. Shown dimensions pertain to installation location. These dimensions are required for compliance with ANSI Standard A117.1. and ADA (Framing shown for reference only). 2. Remove bottom covers from fountains and save the screws. 3. Install the fountains using bolts and washers (provided). Tighten securely. 4. Attach drain tubes to fountains and cut to required length using the freeze resistant boxes as guides. 5.
PAGE 4
ECDFPW314FP CABLE SHEATH ADJUSTMENT To Increase Free Play To Reduce Free Play FIG. 3 FIG. 4 See Fig. 7 Note: Fountain Style May Vary See Fig. 3 FIG. 5 FIG. 6 98011C (Rev. J - 1/08) FIG.
PAGE 5
ECDFPW314FP The freeze resistant package must be mounted on an interior wall in a heated area. The room temperature of the interior heated area must be 50° F (10° C) or higher. The freeze resistant package may be surface or recessed mounted. If recess mounted the surface of the cover must be flush with the interior wall surface. The package is furnished with screws for mounting the cover to the box. If the box is recess mounted, do not fasten the top and bottom of the cover to the box.
PAGE 6
ECDFPW314FP PARTS LIST ITEM NO. PART NO. DESCRIPTION 19 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 NS 40575C 28824C 45662C 45737C 27945C 27946C 40206000 50198C 51667C 75672C 75570C 28790C 55000665 28290C 40045C 55919C 100322740560 15009C 98118C 56092C 28286C 45679C 45805C 50074C 70379C 75541C 111577243890 75520C Drain - Strainer Bracket-Regulator Mounting Push Button Push Button Sleeve Bracket-Basin Bracket-Basin Pivot Retainer Snap Bushing Bumper-Reg.