Installation and Maintenance Manual DSBS130UVPC Table of Contents Declaration of Conformity Association Recommendations for Safeguarding the Environment Explanation of Warning/Safety Icons Introduction Components Guide Product Specifications 2 2 3 3 4 5 6 Before You Begin – Requirements for Installation Mounting Dimensions Operating Environment Water Electrical Tools You Will Need Unpacking the Kit What’s in the Kit Installing the Machine DSBSH130UVPC 7 7 8 8 8 9 9 10 11 Operating the Keypad Routine M
DSBS130UVPC and DSBSH130UVPC Installation and Maintenance Manual Declaration of Conformity D.M. 174 Materials compliant for contact with drinking water TA LY C NI 10 0 % M AD E T I F I C AT E ER I This unit is intended for the dispensing of drinking water, and so the materials that enter into direct contact with water meet the criteria for food-grade components pursuant to the current legislation.
ITPI rosso 032 c I TA LY C 10 IN T I F I C AT E ER 0 % M AD E D.M. 174 ITPI rosso 032 c Recommendations for Safeguarding the Environment Packaging materials The packaging materials are 100% recyclable. Please follow the local guidelines on waste disposal. For safety reasons keep the packaging material out of the reach and sight of children. Scrappage The DSBS130UVPC and DSBSH130UVPC water coolers are made using recyclable material.
DSBS130UVPC and DSBSH130UVPC Installation and Maintenance Manual Introduction The DSBS130UVPC and DSBSH130UVPC coolers bring contemporary style and state-of-the-art technology to commercial water dispensers. DSBS130UVPC and DSBSH130UVPC offer light, compact and powerful performance made entirely from stainless steel. OO Multiple dispensing options: cold still water, cold sparkling water, room temperature still water and/or hot water.
Components Guide DSBS130UVPC Keypad Power button Water inlet CO2 inlet Drip tray Thermostat Power cord DSBSH130UVPC Keypad Boiler switch Power button Water inlet Drip tray CO2 inlet Thermostat Power cord DSBS130UVPC keypad Room Cold still temperature still Cold sparkling dispenser dispenser dispenser DSBSH130UVPC keypad Hot dispensers Cold still dispenser Cold sparkling dispenser 1000003719 (Rev.
DSBS130UVPC and DSBSH130UVPC Installation and Maintenance Manual Product Specifications Specification DSBS130UVPC DSBSH130UVPC Cooling capacity gal/h (lt/h) 1.5 (5.7) 32 6 oz. cups/h 1.5 (5.7) 32 6 oz. cups/h Cold water temperature* 42°F – 50°F (5.5°C – 10°C) 42°F – 50°F (5.
Before You Begin – Requirements for Installation Mounting Dimensions Over counter (includes 4" clearance on sides and back) DSBS130UVPC Depth 23.2” (589mm) DSBSH130UVPC Width 18.3” (465mm) Depth 23.2” (589mm) Width 18.3” (465mm) Height 20.5” (520.7mm) Height 20.5” (520.7mm) Footprint: 10.3” wide x 19.2” deep 261mm x 488mm Footprint: 10.3” wide x 19.2” deep 261mm x 488mm Under counter Depth 3.88" (99mm) Height 12.75" (324mm) Width 3.
DSBS130UVPC and DSBSH130UVPC Installation and Maintenance Manual Operating Environment OO OO Install the machine in a clean, dry, well-ventilated room. It is designed to function correctly in environments with a temperature of 16°C to 32°C – Climatic Class N, (between 61°F and 90°F). Check that the water cooler is level, that it is on a surface that can support its weight and in an environment suitable for its size and use. OO Do not place the machine near a source of heat.
Tools You Will Need (2) 8" adjustable wrenches (1) 12" adjustable wrench (1) 12" pipe cutter (1) 10" adjustable pliers (1) universal screwdriver (1) wire cutting pliers Unpacking the Kit Remove the front panel (labeled FRONT) and cover of the wooden packing case. Remove the cardboard box and the internal protective packaging by sliding them up and over the top. Once you have unpacked the machine, check all components to ensure that they are not damaged.
DSBS130UVPC and DSBSH130UVPC Installation and Maintenance Manual What’s in the Kit (1) 10' coil water tubing (blue) 1/4” OD (1) CO2 regulator (1) DSBS130UVPC or DSBSH130UVPC water cooler PLUS (1) 10' coil water tubing (blue) 3/8” OD (1) supply hose 1/2 ips x 3/8 tube x 12” long (2) 3/8" – quick connect connector (1) water shutoff valve (1) external water filter (1) 10' coil CO2 tubing (natural) 1/4” OD NOTICE: CO2 source is not included and must be supplied separately.
Installing the Machine CAUTION: Wear safety gloves when handling the machine. Metal edges are sharp, and touching them could result in minor or moderate injury. 1. Install external water filter and CO2 cylinder. 1. Use (2) Phillips head screws to mount bracket to under-counter wall. 2. Use (4) Phillips head screws to mount filter head to bracket. 3. Remove cap from filter. Insert filter into filter head and turn clockwise (right) until it stops.
DSBS130UVPC and DSBSH130UVPC Installation and Maintenance Manual 2. Cut, size and connect water and CO2 piping to fit your installation. NOTICE: The water pressure entering the machine must be between 14.5 psi (0.10 MPa) minimum and 51 psi (0.35 MPa) maximum. If the inlet water pressure is higher than 51 psi, the water pressure regulator supplied must be used. NOTICE: An incoming flow rate of >1.0 gallon/minute is recommended for optimal quality of sparkling water.
3. Place the machine in its operating location. NOTICE: Ensure machine remains level while being lifted into place. 4. Connect external water and CO2 piping. DSBS130UVPC Water input DSBSH130UVPC Water input CO2 input CO2 input 5. Plug the machine into the wall socket and turn it on. 1. Connect the power cable to the nearest socket. 2. Flip the power switch at the rear of the machine (A) to the "I" position. DSBS130UVPC A A DSBSH130UVPC B B B B A A 1000003719 (Rev.
DSBS130UVPC and DSBSH130UVPC Installation and Maintenance Manual 6. Purge the water lines. 1. Place receptacle beneath tap to catch dispensed water. Discard water as necessary. DSBS130UVPC Press dispensing button DSBSH130UVPC Press dispensing button 2. Allow water to run continuously until flow is clear of air. 3. Repeat for all taps. 7. Turn on the boiler (DSBSH130UVPC only). NOTICE: Never turn on the boiler unless you have filled the machine with water.
8. Open the CO2 valve. 1. Using a screwdriver slowly turn valve screw counterclockwise (left) to open valve. 2. Continue until pressure reads 50 to 58 psi max. 9. Re-purge the line for sparkling water. NOTICE: The water will flow flat at first, then gradually become more sparkling as the line is purged of still water. 10. Allow machine to complete initial chilldown. NOTICE: Complete water heating will require around 10 minutes.
DSBS130UVPC and DSBSH130UVPC Installation and Maintenance Manual Operating the Keypad DSBS130UVPC To dispense your water serving Hold down the button for that dispenser. To stop dispensing your water serving Release the button for that dispenser. Operating the Keypad DSBSH130UVPC To dispense your water serving Hold down the button for that dispenser. Note: For safety reason, to dispense hot water you must press and hold down the 2 hot water buttons at the same time.
Routine Maintenance Daily OO Clean all external surfaces of the machine, the drip tray and the dispensing nozzles. NOTICE: It is recommended that all external components of the product be cleaned daily. It is recommended that you use dish soap, warm water and a clean, soft cloth to clean the product. DO NOT USE THE FOLLOWING PRODUCTS: Do not use ... chlorine bleach solutions on the product. Chlorides found in most soaps, detergents, bleaches and cleaners can attack stainless steel.
DSBS130UVPC and DSBSH130UVPC Installation and Maintenance Manual Annually OO Replace the water filter after 6000 gallons or a maximum of 1 year, or earlier depending on water quality. NOTICE: The filter head has an internal shutoff valve that stops the flow of water when the filter is removed. It is not necessary to shut off the water supply. 1. Turn used filter counterclockwise (to the left) 1/4 turn to remove from filter head. Pull filter away from head and remove. 2.
OO Set the thermostat 1. Set the thermostat between 5 and 6 to control the temperature of the cold water. COLDER 1 2 3 OFF 4 7 6 5 1000003719 (Rev.
DSBS130UVPC and DSBSH130UVPC Installation and Maintenance Manual Troubleshooting Problem No water dispense Problem Low flow dispense Problem Sparkling water doesn’t come out Problem Water is not cold enough Problem Hot water is not hot 20 Possible Cause Action To Take The main water valve is closed Open the valve The power switch is set to OFF Set the power switch to ON Malfunction in the ribbon cable connection/ spade connectors Repair connection to main circuit board The water inlet solenoi
Problem Poor sparkling water quality Problem Only CO2 gas comes out when sparkling water button is pressed Problem Dripping water Problem Noise/Vibration Possible Cause Action To Take Incorrect air gap in the carbonator Close the CO2 cylinder valve, pull up the ring on safety valve (on the carbonator bowl head) until all air gap is out Use of rinse aid or highly polished glass Avoid excessive use of rinse aid The CO2 regulator is set low Set the CO2 regulator between 55-60 psi (3.
DSBS130UVPC and DSBSH130UVPC Installation and Maintenance Manual Contacting Customer Support Elkay Manufacturing Company 2222 Camden Court Oak Brook, IL 60523 800-726-0553 22
Replacement Parts DSBSH130UVPC DSBS130UVPC x DSCABBSH Part Number Product Name x 1000002622 Motor Fan 120x120x25 x x 1000002623 Booster Pump x x 1000003890 Level Control x x 1000002625 General Power Switch x x 1000003892 Ice Bank Thermostat Dry Cooling K50 x x 1000002627 Feet 4MA x x 1000002631 Inlet Solenoid Valve x x 1000003894 Exit Solenoid Valve 2IN-1OUT 1000003895 Exit Solenoid Vavle (hot) x x x 1000003896 Flow Control 6mm x x 1000003897 Flow CONTROL 8mm x
160217