Installation Sheet

ManualsBrandsElkay ManualsKitchenCrosstown Stainless Steel Kitchen Sink Bottom Grid - Fits Bowl Size 16 in. x 16 in.

PAGE 1 98421C (Rev. C - 09/17)

HDFF-EBPFR*A HDFF-BLEBPFR*A HDFF-BLREBPFR*A

Halsey Taylor Owners Manual

HDFF-EBPFR HDFF-BLEBPFR HDFF-BLREBPRF

Freeze Resistant Fountain

HDFF-EBPFR HDFFBLEBP - FR HDFFBLREBP - FR

Halsey Taylor Fountains are among the easiest to install Fountains on the market today. To assure you install

these models easily and correctly, PLEASE READ THESE SIMPLE INSTRUCTIONS BEFORE STARTING

THE INSTALLATION. CHECK YOUR INSTALLATION FOR COMPLIANCE WITH PLUMBING, ELECTRICAL,

AND OTHER APPLICABLE CODES. After installation, leave these instructions with the Fountain for future

reference. This Freeze Resistant Fountain is shipped in two separate cartons. The second carton(s) contains

the Freeze Resistant Package(s) HTFRB1 that are installed on an interior heated wall. The interior space must

maintain a minimium temperature of 50° F (10° C). Refer to the Freeze Resistant Package for the rough-in

dimensions for installation.

INSTALLER

IMPORTANT

ALL SERVICE TO BE PERFORMED BY AN AUTHORIZED SERVICE PERSON.

IMPORTANT! INSTALLER PLEASE NOTE.

THE GROUNDING OF ELECTRICAL EQUIPMENT SUCH AS TELEPHONE, COMPUTERS, ETC. TO WATER LINES

IS A COMMON PROCEDURE. THIS GROUNDING MAY BE IN THE BUILDING OR MAY OCCUR AWAY FROM

THE BUILDING. THIS GROUNDING CAN CAUSE ELECTRICAL FEEDBACK INTO A FOUNTAIN, CREATING AN

ELECTROLYSIS WHICH CAUSES A METALLIC TASTE OR AN INCREASE IN THE METAL CONTENT OF THE

WATER. THIS CONDITION IS AVOIDABLE BY USING THE PROPER MATERIALS AS INDICATED. ANY DRAIN

FITTINGS PROVIDED BY THE INSTALLER SHOULD BE MADE OF PLASTIC TO ELECTRICALLY ISOLATE THE

FOUNTAIN FROM THE BUILDING PLUMBING SYSTEM.

Summary of content (16 pages)

PAGE 1
HDFF-EBPFR*A HDFF-BLEBPFR*A HDFF-BLREBPFR*A Halsey Taylor Owners Manual HDFF-EBPFR HDFF-BLEBPFR HDFF-BLREBPRF Freeze Resistant Fountain HDFF-EBPFR HDFFBLEBP - FR HDFFBLREBP - FR INSTALLER Halsey Taylor Fountains are among the easiest to install Fountains on the market today. To assure you install these models easily and correctly, PLEASE READ THESE SIMPLE INSTRUCTIONS BEFORE STARTING THE INSTALLATION. CHECK YOUR INSTALLATION FOR COMPLIANCE WITH PLUMBING, ELECTRICAL, AND OTHER APPLICABLE CODES.
PAGE 2
98421C (Rev. C - 09/17) PAGE 2 "D" 26 13/16" 681mm 7 1/4" 184mm 5 1/4" 133mm 24 9/16" 625mm "E" WALL PLATE ASSEMBLY DIA. (44 mm) HOLE FOR WASTE LINE DIA. (22 mm) HOLE FOR WATER SUPPLY DIA. (22 mm) HOLE FOR OPERATING CABLE DIA. (6 mm) HOLE FOR MOUNTING PLATE TO WALL DIA.
PAGE 3
12 1/8" 309mm 19 3/4" 502mm PAGE 3 2 5/8" 66mm 12" 305mm MAX. WALL THICKNESS 3 5/8" 91mm FINISHED FLOOR 27" 686mm ADA REQUIREMENT 6 1/2" 167mm 18" 457mm 5/8" 16mm HDF-EBP-FR WITH WALL PLATE ASSEMBLY ROUGH-IN DRAWINGS 28 13/16" 732mm 17 15/16" 14 7/16" 455mm 13 3/8" 366mm 339mm HDFF-BLEBPFR*A 1. Wall should already be framed for the fountain using dimensions shown in Fig. 1. Shown dimensions pertain to installation location. These dimensions are required for compliance with ANSI Standard A117.1.
PAGE 4
98421C (Rev. C - 09/17) LEGEND A = 1-3/4" B = 7/8" C = 7/8" D = 1/4" 12" 305mm MAX. WALL THICKNESS FIG. 3 DIA. (44 mm) HOLE FOR WASTE LINE DIA. (22 mm) HOLE FOR WATER SUPPLY DIA. (22 mm) HOLE FOR OPERATING CABLE DIA. (6 mm) HOLE FOR MOUNTING PLATE TO WALL 7 1/4" 184mm 12 1/8" 307mm 43 1/2" 1105mm MPW101 MTG. PLT.
PAGE 5
12 1/8" 308mm 19 3/4" 502mm 27" 686mm ADA REQUIREMENT 6 1/2" 165mm 3 13/16" 97mm FINISHED FLOOR 12" 305mm MAX. WALL THICKNESS 18" 457mm FINISHED WALL 2 5/8" 66mm 5/8" 16mm HDF-EBP-FR WITH MP101 MUNTING PLATE ROUGH-IN DRAWINGS PAGE 5 17 1/2" 444mm 3 5/8" 91mm 13" 330mm 14" 355mm MPW101 MTG. PLT. REF. SEPARATE INSTALLATION INSTRUCTIONS FOR DETAILS 28 9/16" 725mm HDFF-BLEBPFR*A 1. Wall should already be framed for the fountain using dimensions shown in Fig. 1.
PAGE 6
98421C (Rev. C - 09/17) LEGEND A = 1-3/4" B = 7/8" C = 7/8" D = 1/4" E = 3/8" 12 1/8" 308mm 7 1/4" 185mm FIG. 5 12" 305mm MAX. WALL THICKNESS PAGE 6 36 1/4" 921mm 32 13/16" 833mm 7 1/4" 184mm 24 9/16" 625mm 34 9/16" 878mm WALL PLATE ASSEMBLY E "B" "A" 16" 406mm "A" 16" 406mm FINISHED FLOOR "C" "C" D 7 1/4" 184mm 26 13/16" 681mm 30 1/4" 768mm 28 9/16" 725mm "B" 5 1/4" 133mm 5 1/4" 133mm 1 1/2" 38mm 44 3/4" 1136mm HDFF-BLEBPFR*A DIA. (44 mm) HOLE FOR WASTE LINE DIA.
PAGE 7
6 11/16" 170mm 12 1/8" 309mm FINISHED FLOOR 38 1/2" 978mm PAGE 7 27" 686mm ADA REQUIREMENT 6 1/2" 165mm 3 11/16" 94mm 3 5/8" 91mm 2 5/8" 66mm 12" 305mm MAX. WALL THICKNESS 18" 457mm 5/8" 16mm 28 9/16" 726mm 23 11/16" 601mm 20 3/16" 512mm 17 11/16" 449mm 14 3/16" 360mm 34 9/16" 878mm HDFF-BLEBPFR*A 1. Wall should already be framed for the fountain using dimensions shown in Fig. 3. Shown dimensions pertain to installation location.
PAGE 8
98421C (Rev. C - 09/17) 12 1/8" 307mm 7 1/4" 184mm DIA. (44 mm) HOLE FOR WASTE LINE DIA. (22 mm) HOLE FOR WATER SUPPLY DIA. (22 mm) HOLE FOR OPERATING CABLE DIA. (6 mm) HOLE FOR MOUNTING PLATE TO WALL 7 1/4" 184mm 12 1/8" 307mm PAGE 8 36 1/4" 921mm 43 1/2" 1105mm 34 9/16" 878mm BACK PANEL D 6 5/8" 168mm 1/2" 13mm A C 1/2" 13mm B 1/2" 13mm 16" 406mm FINISHED FLOOR 18 3/4" 476mm 32" 813mm 1/2" 13mm A C 28 9/16" 725mm 30 1/4" 768mm MPW200 MTG. PLT.
PAGE 9
6 5/8" 168mm 38 1/2" 978mm 12 1/8" 308mm 27" 686mm ADA REQUIREMENT 6 1/2" 165mm 3 13/16" 97mm FINISHED FLOOR 12" 305mm MAX. WALL THICKNESS 18" 457mm FINISHED WALL 2 5/8" 66mm 5/8" 16mm PAGE 9 3 5/8" 91mm 13" 330mm 14" 355mm 23 1/2" 597mm 20" 508mm 17 1/2" 444mm MPW200 MTG. PLT. REF. SEPARATE INSTALLATION INSTRUCTIONS FOR DETAILS 28 9/16" 725mm 34 9/16" 878mm HDFF-BLEBPFR*A 1. Wall should already be framed for the fountain using dimensions shown in Fig. 3.
PAGE 10
98421C (Rev. C - 09/17) LEGEND A = 1-3/4" B = 7/8" C = 7/8" D = 1/4" E = 3/8" 12 1/8" 308mm 7 1/4" 185mm FIG. 9 12" 305mm MAX. WALL THICKNESS PAGE 10 24 9/16" 625mm 28 9/16" 725mm 30 1/4" 768mm 26 13/16" 681mm 7 1/4" 184mm "B" "E" WALL PLATE ASSEMBLY "C" "A" 16" 406mm FINISHED FLOOR "A" "C" 16" 406mm 2 3/4" 70mm 7 1/4" 184mm "D" 32 13/16" 833mm 34 9/16" 878mm "B" 1 1/2" 38mm 5 1/4" 133mm 5 1/4" 133mm 36 1/4" 921mm 44 11/16" 1136mm HDFF-BLEBPFR*A DIA. (44 mm) HOLE FOR WASTE LINE DIA.
PAGE 11
6 5/8" 168mm 12 1/8" 309mm FINISHED FLOOR 38 1/2" 978mm 33" 836mm 6 1/2" 167mm 3 13/16" 96mm PAGE 11 3 5/8" 91mm 2 5/8" 66mm 12" 305mm MAX. WALL THICKNESS 18" 457mm 5/8" 16mm 20 3/16" 512mm 17 11/16" 449mm 14 3/16" 360mm 28 9/16" 726mm 23 11/16" 601mm 34 9/16" 878mm HDFF-BLEBPFR*A 1. Wall should already be framed for the fountain using dimensions shown in Fig. 3. Shown dimensions pertain to installation location. These dimensions are required for compliance with ANSI Standard A117.1.
PAGE 12
98421C (Rev. C - 09/17) LEGEND A = 1-3/4" B = 7/8" C = 7/8" D = 1/4" 12 1/8" 308mm 7 1/4" 185mm 12" 305mm MAX. WALL THICKNESS PAGE 12 30 1/4" 768mm 43 1/2" 1105mm 28 9/16" 725mm 1 11/16" 43mm MPW200 MTG. PLT. D 6 5/8" 168mm A 1/2" 13mm C 1/2" 13mm B 1/2" 13mm 16" 406mm FINISHED FLOOR 18 3/4" 476mm A 32" 813mm C 1/2" 13mm B 34 9/16" 878mm 1 11/16" 43mm 36 1/4" 921mm BACK PANEL HANGER BRACKET 3 1/4" 82mm HDFF-BLEBPFR*A DIA. (44 mm) HOLE FOR WASTE LINE DIA.
PAGE 13
PAGE 13 12 1/8" 308mm 33" 838mm HRFSFR 20 3/8" 518mm 3 13/16" 97mm FINISHED FLOOR 12" 305mm MAX. WALL THICKNESS 18" 457mm HRFEFR 2 5/8" 66mm 5/8" 16mm 34 9/16" 878mm HRFSFR 3 5/8" 91mm 23 1/2" 17 1/2" 597mm 444mm HRFSFR HRFEFR 14" 28 9/16" 355mm 20" 725mm HRFEFR 508mm 13" HRFEFR 330mm HRFSFR HRFEFR MPW200 MTG. PLT. REF. SEPARATE INSTALLATION INSTRUCTIONS FOR DETAILS 1. Wall should already be framed for the fountain using dimensions shown in Fig. 3.
PAGE 14
HDFF-EBPFR*A HDFF-BLEBPFR*A HDFF-BLREBPFR*A CABLE SHEATH ADJUSTMENT To Increase Free Play To Reduce Free Play FIG. 13 FIG. 14 See Fig. 16 FIG. 15 See Fig. 13 6,7 SEE FIG. 21 SEE FIG. 22 17 FIG. 16 98421C (Rev. C - 09/17) 15 2 FIG.
PAGE 15
HDFF-EBPFR*A HDFF-BLEBPFR*A HDFF-BLREBPFR*A The freeze resistant package must be mounted on an interior wall in a heated area. The room temperature of the interior heated area must be 50° F (10° C) or higher. The freeze resistant package may be surface or recessed mounted. If recess mounted the surface of the cover must be flush with the interior wall surface. The package is furnished with screws for mounting the cover to the box.
PAGE 16
HDFF-EBPFR*A HDFF-BLEBPFR*A PARTS LIST ITEM NO. PART NO. 1 2 3 4 5 6 45678C 0000000930 75570C 98872C 28630C 28170C 28159C 27171C 28625C 28626C 28659C 28824C 40045C 28627C 97446C 45662C 45737C 28840C 28841C 28842C 56092C 56163C 56369C 75672C 111577243890 75520C 75541C 7 8 9 10 11 12 13 14 15 16 17 18 NS NS NS HDFF-BLREBPFR*A FIG. 20 14 DESCRIPTION DRAIN PLUG 1-1/2" DRAIN/TAILPIPE ASSEMBLY SCREW-#10 x .50 PINNED TORX KIT - PIVOT BRACKET BOTTOM COVER PLATE WALL MTG. PLATE ASSY. (HDF-EBPFR) WALL MTG.