Installation

ManualsBrandsElkay ManualsPlumbingEZS to EZO Retrofit Kit

Page 1 1000005818 (Rev. A - 06/20)

1000005817

INSTALLATION MANUAL

To insure you install this Kit easily and correctly, PLEASE READ THESE

SIMPLE INSTRUCTIONS BEFORE STARTING THE INSTALLATION. CHECK

YOUR INSTALLATION FOR COMPLIANCE WITH PLUMBING, ELECTRICAL, AND

OTHER APPLICABLE CODES.

IMPORTANT

THIS IS AN INDOOR APPLICATION ONLY.

ALL SERVICE TO BE PERFORMED BY AN

AUTHORIZED SERVICE PERSON.

IMPORTANT! INSTALLER PLEASE NOTE.

THE GROUNDING OF ELECTRICAL EQUIPMENT SUCH AS TELEPHONE, COMPUTERS, ETC. TO WATER LINES

IS A COMMON PROCEDURE. THIS GROUNDING MAY BE IN THE BUILDING OR MAY OCCUR AWAY FROM

THE BUILDING. THIS GROUNDING CAN CAUSE ELECTRICAL FEEDBACK INTO A FOUNTAIN, CREATING AN

ELECTROLYSIS WHICH CAUSES A METALLIC TASTE OR AN INCREASE IN THE METAL CONTENT OF THE

WATER. THIS CONDITION IS AVOIDABLE BY USING THE PROPER MATERIALS AS INDICATED. ANY DRAIN

FITTINGS PROVIDED BY THE INSTALLER SHOULD BE MADE OF PLASTIC TO ELECTRICALLY ISOLATE THE

FOUNTAIN FROM THE BUILDING PLUMBING SYSTEM. WE SUGGEST THAT THE BOTTLE FILLING STATION

AND WATER COOLER BE PROTECTED BY A GROUND FAULT CIRCUIT INTERRUPTER (GFCI).

INSTALLER

TOOLS REQUIRED

BUT NOT PROVIDED:

GLOVES

SAFETY GLASSES

NEEDLE NOSE AND REGULAR PLIERS

¼ AND 5/16 NUT DRIVERS

FLAT HEAD SCREWDRIVER

T-20 TORX BIT OR 7/64 ALLEN WRENCH

BLACK MARKER

BUCKET

MULTI-METER

RETROFIT KIT EZS TO EZO

Summary of content (7 pages)

PAGE 1
000005817 INSTALLATION MANUAL RETROFIT KIT EZS TO EZO IMPORTANT THIS IS AN INDOOR APPLICATION ONLY. ALL SERVICE TO BE PERFORMED BY AN AUTHORIZED SERVICE PERSON. TOOLS REQUIRED BUT NOT PROVIDED: GLOVES SAFETY GLASSES NEEDLE NOSE AND REGULAR PLIERS ¼ AND 5/16 NUT DRIVERS FLAT HEAD SCREWDRIVER T-20 TORX BIT OR 7/64 ALLEN WRENCH BLACK MARKER BUCKET MULTI-METER IMPORTANT! INSTALLER PLEASE NOTE. THE GROUNDING OF ELECTRICAL EQUIPMENT SUCH AS TELEPHONE, COMPUTERS, ETC. TO WATER LINES IS A COMMON PROCEDURE.
PAGE 2
1000005817 ●● ●● ●● ●● ●● WATER COOLER PREPARATION Remove Lower wrapper on the cooler by removing the (4) screws using a 5/16 nut driver Shut off water to the cooler Remove water pressure by pressing on any of the cooler push bars until no water comes out of the bubbler Unplug the water cooler Remove the P-trap from the cooler drain 1. Remove the (4) screws – 2 per side on the upper shroud using the Torx bit or Allen Wrench. (See Fig. 1) Note: The kit is for refrigerated units only. 2.
PAGE 3
1000005817 12. Remove the white wire from the compressor relay and the black wire from the overload. Leave the fan wires connected. Fig 5 & 6 Fig. 5 Fig. 6 13. Remove the power cord ground connection on the frame using the ¼ nut driver. Keep this screw it will be needed to connect the ground wire on the new power cord. Fig. 7 Fig. 7 Page 3 1000005818 (Rev.
PAGE 4
1000005817 14. Using pliers, squeeze the strain relief on the power cord and pull down to remove the cord from the bracket. Fig 8 15. Remove all remaining wires from the solenoid and cold control and discard. Fig. 8 16. Measure 23 inches from the plug end of the power cord and place the strain relief on the cord at that point. Fig. 9 Fig. 9 17. Squeeze the strain relief and place in the slot in the bracket that the old power cord was removed. Push up until it locks into place. Fig. 10 Fig.
PAGE 5
1000005817 18. Put the ground screw in the ring terminal on the green ground wire on the power cord. Tighten the screw back into the frame where the old ground wire was connected. Tighten the screw so that the terminal will not turn. To make sure that the grounding connection is secure, use a multi-meter and check for continuity. Place one probe on the round connector on the plug and the other probe on the frame. Fig. 11 Fig. 11 19.
PAGE 6
1000005817 21. Replace the cover over the compressor electricals. Place the slot on the cap on the lower arm on the compressor, slide all the wire into the large slot in the cap. Rotate the cap upwards and push until it snaps into place. Fig. 14a, 14b & 14c Fig. 14a Fig. 14b Fig. 14c 22. Connect the black wire from the kit.
PAGE 7
1000005817 ●● Push the water line down so it can be connected to the evaporator. Push the water line into the fitting on the evaporator until it is up to the line that was drawn on the water line earlier. ●● Spin the fan blade to ensure it spins freely and there are not any wires or that the water line is not in it. ●● Place the (4) screws back in to hold the basin/shroud assembly to the frame. ●● Reconnect the P-trap. ●● Remove the plastic covering the sensor bar.