User Manual

Measure and note the width and the height
of the square or rectangle formed from the
VESA holes pattern .
01
02
Monitor PlateWall Plate Extenders
Nuts Bolts
3B
3A
x2
x1x1
x2
4A
x8
4B
x8
Step 2 Mesure your TV pattern
W
H
2M2M
100mm ≈ 4in.
130mm≈ 5 1/8in.
200mm ≈ 8in.
300mm ≈ 11 3/4in
340mm ≈ 13 3/4in.
400mm≈ 16in.
Select the configuration A , B , C, D, or E to use based on the measurement from STEP 2.
If your TV hole pattern is greater than 200x200mm, attach extenders [3A] and [3B] to monitor
plate [02] using Nut [4A] and Bolt [4B].
for VESA hole pattern:
300x300mm, 400x400mm
200 mm
200 mm
400 mm
400 mm
400 mm
400 mm
400 mm
300 mm
300 mm
300 mm
300 mm
300 mm
for VESA hole
pattern:
200x300mm,
200x400mm
B
for VESA hole
pattern:
400x300mm,
D
E
for VESA hole pattern:
100x100mm, 130x130mm,200x100mm, 200x200mm.
200 mm
100 mm
130 mm
200 mm
100 mm
130 mm
A
VESA Pattern
(WxH)
Configuration
VESA Pattern
(WxH)
Configuration
100mm x 100mm A 300mm x 200mm C
130mm x 130mm A 300mm x 300mm E
200mm x 100mm A 400mm x 200mm C
200mm x 200mm A 400mm x 300mm D
200mm x 300mm B 400mm x 400mm E
200mm x 400mm B
M-A
Use the shorter screws
M-B
M-C
M-E
Not for M8 screws
M-FM-D
Step 3-3
Attach the brackets
(a) For Flat Back
(b) For Round Back / Extra Space
Hardware Included
Hardware (Wall /Product)
5/16 x 2½ in
Lag Bolts
x3
x1
CA
Washers
Ø8mm
x3
B
Open-end wrench
Max:400x400mm/16x16"
Min:75x75mm /3x3"
26"~55"
(V5.1)
YD1003-A
INSTALLATION INSTRUCTION
Philips Screws
M6 x 15mm
M6 x 30mm
Philips Screws
M4 x 12mm
M4 x 30mm
Washers
Ø6mm
M4-5-6
Spacers
L10mm
x4
x4
x4x4
Philips Screws
M8 x 25mm
M8 x 45mm
x4
x4 x8 x4
Spacers
L5mm
x8
TV Screws / Washers
M-A M-B M-C M-D M-E M-F
Step 1-1 Select TV screw diameter
Thread screws by hand into the threaded holes on the back of your TV to select which screw
diameter fits your TV.
M6M4
M8
Correct
Correct
Too Long
Too Short
Step 1-2 Select TV screw length
for VESA hole pattern:
400x200mm, 300x200mm
C
4A
4B
C
3B
3B
3A
3A
3A
02 4A 4B
3B
M-A
Use the shorter screws
M-B
M-C
M-E
Not for M8 screws
Top of TV
Top of TV
Max:
(40KG)
88LBS
Safety Caution
Must Check Before Getting Started
Installation Tools (Not Included)
Band
Tape
2M
Socket
Wrench
ScrewdriverPencil Electrodrill
Stud
Finder
HammerAwl
Wood
Drill Bit
Masonry
Drill Bit
Wood Stud Installation Concrete Installation
1/2"
(13mm)
3/8"
(10mm)
7/32"
(5.5mm)
Step 3-1 Select monitor plate configuration
Step 3-2
Assemble monitor plate and extenders
Bubble Level ×1
No!
No!
When attaching brackets to the flat screen, be careful not to over tighten screws and
be sure that screws do not bottom out in the mounting holes.
MAX:400mm/16"
MAX:
400mm/16"
Min. 8"
(203mm)
Solid concrete wall
CAUTION: DO NOT install into drywall alone.
Max:
(40KG)
88LBS
Min. Wood Stud Size:
nominal 2”(51mm)
actual 1 1/2”(38mm)
Min. Wood Stud Size:
nominal 4”(102mm)
actual 3 1/2”(89mm)
<16mm(5/8")
Drywall with wood studs
If you have any questions, please contact us.
Please read this instruction carefully before installation.
If you do not understand these instructions or have doubts about the safety of the installation, assembly
or use of this product, please contact us.
● This product is designed for use in wood stud and solid concrete wall.
- DO NOT install into drywall alone.
● The wall must be capable of supporting five times the weight of the TV and mount combined.
● Do not apply this product to any purpose not indicated by ELIVED.
●
Incorrect installation may result in product damage or body inj
for any damage or injury resulted from incorrect installation, incorrect assembly or misuse.
WARNING: This product contains small items that could be a choking hazard if swallowed.
Before starting assembly, verify all parts are included and undamaged. For parts shortage or damage,
please contact us.
ury. ELIVED shall bear no responsibility
4
1 2
43 5