User Manual ECS SI mPC
Copyright This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without written consent of the author. Version 1.0 Disclaimer The information in this document is subject to change without notice.
Any special accessories needed for compliance must be specified in the instruction manual. Use only shielded and terminated cables to connect I/O devices to this equipment. Warning! Any changes or modifications made to the equipment which are not expressly approved by the relevant standards authority could void your authority to operate the equipment.
^ŽƵƚŚ <ŽƌĞĂ D ͗ ůĂƐƐ EŽƟĐĞ 이 기기는 가정용(B급) 전자파적합기기로서 주 로 가정에서 사용하는 것을 목적으로 하며, 모든 지역에서 사용할 수 있습니다. ^ŽƵƚŚ <ŽƌĞĂ Z&͗ tĂƌŶŝŶŐ ƐƚĂƚĞŵĞŶƚ 해당 무선설비는 전파혼신 가능성이 있으므로 인명안전과 관련된 서비스는 할 수 없음 Korea Certification mark. Includes an adjacent MSIP (Ministry of Science, ICT & future planning) certification number.
Packing List Before setting up the system, check that the items listed below are included and in good condition. If any items are missing, please contact your dealer immediately. ECS SI mPC x1 Adapter x1 User Manual x1 Antenna x2 VESA Mount Bracket x1 (Optional) W Warning! Attention! (Optional) To prevent electric shock, Do not remove cover. T No user serviceable parts inside, refer servicing to qualified personnel. Pour éviter un choc électrique, ne pas retirer le couvercle.
Safety Instructions 1. 2. 3. Read these safety instructions carefully. Keep this User Manual for later reference. Disconnect this equipment from any AC outlet before cleaning. Use a damp cloth. Do not use liquid or spray detergents for cleaning. 4. For plug-in equipment, the power outlet socket must be located near the equipment and must be easily accessible. 5. 6. Keep this equipment away from humidity. Put this equipment on a reliable surface during installation.
Contents Chapter Chapter 1 System Information .............................1 1.1 Introduction ................................................................................................ 2 1.2 Specifications ............................................................................................. 2 1.3 Cleaning/Disinfecting ................................................................................. 3 2 Getting Started ....................................4 2.1 System Tour .........
Chapter 1 1 System Information
1.1 Introduction The product has onboard Intel® Bay Trail-M SoC for personal micro desktop markets or educational usage. Below is a brief summary of the computer’s many feature: NOTE: The features listed in this section is for your reference only. The exact configuration of the system depends on the model purchased. 1.2 Specifications Item Description CPU/SoC Intel® Bay Trail-M SoC Celeron N2830 TDP 7.
Item Description Adapter ASIAN POWER DEVICES INC. 12V, 3A, 36W WA-36A12FU-AAAM WA-36A12FG-AAAA WA-36A12FK-AAAA WA-36A12FS-AAAA WA-36A12FN-AAAA KUANTECH INCORPORATED COMPANY 12V, 3A, 36W KSAS0361200300D5 KSAS0361200300HU KSAS0361200300HE KSAS0361200300HK KSAS0361200300HA 1.3 Cleaning/Disinfecting During normal use ECS SI mPC may become solied and should, therefore, be cleaned regularly. Steps: 1. Wipe ECS SI mPC with a clean cloth that has been moistened in the cleaning solution. 2. 3.
Chapter 2 Getting Started 2
2.1 System Tour Before you start to set up system, take a moment to become familiar with the location sand purposes of the controls, drives, connections and ports, which are illustrated in the figures below. Wireless charger LED (Optional) (Power transfer Green blink, Fault Red blink) Wireless charger/NFC (Optional) HDD LED Power Button Figure 2.1 Top View Speaker (Optional) Figure 2.2 Bottom View Kensington Lock Figure 2.
USB 3.0 IR sensor DC Jack Thermal opening HDMI Combo Audio Jack (Mic In& Line out) RJ45 port USB 2.0 Figure 2.
2.2 Distri ution Description The operating system is based on Windows .1 64bit / FreeDOS. 2.3 owering the System Connecting a 12 adapter to the DC-In ack, the system will start up automatically. DC-In DC-In Figure 1: Location of DC-In ack.
Chapter 2 3 ardware Installation
3.
a le o Mothe oa B 1. FAN 2. PWR BTN 3. System Fan 4. BAT1 5. SPEAKER 5. W CHG 6. MiniPCIE . LED BAR . SATA . SATA PWR 10. CLR CMOS 11. NFC 12. SODIMM lo Co onents CO O TS System cooling fan connector Power button System Fan Battery connector Speaker connector Wireless charger connector 1 M.
I/O orts 1. Com o udio ac ic In ine Out Use the combo audio ack to connect the microphone, speaker or headphone. 2. SB2. orts Use the USB 2.0 ports to connect USB 2.0 devices. 3. 4 ort Connect an RJ-45 ack to the LAN port to connect your computer to the Network. D cti ity in 4. D I D Status D Link LED Description OFF No data Orange blinking Active OFF No link Green Link ort Connect the display device to the HDMI port. . DC 12V ac Connect the DC IN ack to the power adapter. .
3.2 Installing the other oard 1. Safety Instructions Follow these safety precautions when installing the motherboard: Wear a grounding strap attached to a grounded device to avoid damage from static electricity. Discharge static electricity by touching the metal case of a safely grounded ob ect before working on the motherboard. Leave components in the static-proof bags.
3. Installing ardware Installin Me o Mo ules This motherboard accommodates one memory module. It can support one 204-pin DDR3L 1333/1066 MH . Do not remove any memory module from its antistatic packaging until you are ready to install it on the motherboard. Handle the modules only by their edges. Do not touch the components or metal parts. Always wear a grounding strap when you handle the modules. ou must install at least one module in any of the four slots. Total memory capacity is GB.
Installin A on Ca s The slots on this motherboard are designed to hold expansion cards and connect them to the system bus. Expansion slots are a means of adding or enhancing the motherboard’s features and capabilities. With these efficient facilities, you can increase the motherboard’s capabilities by adding hardware that performs tasks that are not part of the basic system.
Che in u e Settin s This section explains how to set motherboard. Conne tin umpers for correct configuration of the tional e i es Refer to the following for information on connecting the motherboard’s devices. 1. F System cooling fan connector Connect the system cooling fan to the FAN connector.
2. B T1 Battery connector 3.
4. .
.S T .
8.
