User's Manual

ManualsBrandsELITEGROUP COMPUTER SYSTEMS ManualsElectronicsLogistic Monitoring Gateway

Federal Communications Commission (FCC)

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and the receiver

• Connect the equipment onto an outlet on a circuit different from that to

which the receiver is connected

• Consult the dealer or an experienced radio technician for help

Shielded interconnect cables and a shielded AC power cable must be employed with

this equipment to ensure compliance with the pertinent RF emission limits

governing this device. Changes or modifications not expressly approved by the

system’s manufacturer could void the user’s authority to operate the equipment.

FCC Label Compliance Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the follow-

ing two conditions:

(1) This device may not cause harmful interference

(2) This device must accept any interference received, including interference that

may cause undersired opreation

RF Exposure Information (SAR)

This device meets the government’s requirements for exposure to radio waves.

This device is designed and manufactured not to exceed the emission limits for

exposure to radio frequency (RF) energy set by the Federal Communications

Commission of the U.S. Government.

The exposure standard employs a unit of measurement known as the Specific

Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6 W/kg. Tests for SAR are

conducted using standard operating positions accepted by the FCC with the EUT

transmitting at the specified power level in different channels.

The FCC has granted an Equipment Authorization for this device with all reported

SAR levels evaluated as in compliance with the FCC RF exposure guidelines. SAR

information on this device is on file with the FCC and can be found under the Display

Grant section of www.fcc.gov/eot/ea/fccid after searching on FCC ID: WL6GWS-CSCG

Summary of content (13 pages)

PAGE 1
Federal Communications Commission (FCC) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
PAGE 2
Canada, Industry Canada (IC) Notices This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Canada, avis d’Industry Canada (IC) Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.
PAGE 3
Safety Instruction Your system is designed and tested to meet the latest standards of safety for information technology equipment. However, to ensure your safety, it is important that you read the following safety instructions. Setting up your system • • • • • Read and follow all instructions in the documentation before you operate your system. Do not use this product near water or a heated source such as a radiator. Set up the system on a stable surface. Openings on the chassis are for ventilation.
PAGE 4
Nordic Lithium Safety Notice (for lithium-ion batteries) Safety Notice: Danger of explosoin if battery is incorrectly replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions. Attetion during use 1. Do not place this product underneath heavy loads or in an unstable position. 2. Do not use or expose this product around magnetic fields as magnetic interference may affect the performance of the product. 3.
PAGE 5
Brief Introduction Specifications Item Processor Spec Description Intel® Atom X3 Telit HE922 Cache:16Kbytes L1 Memory: eMMC interface 8GB RAM: 8Gb LDDR3 Charging Port (Extension Battery/ CST) External IO Port Charging Port (Micro USB output5V3A / input 110V~240V) Micro USB Debug Buzzer Buzzer LED LED(CPU /Device Status) Display OLED 54.
PAGE 6
Castle canyon provisioning overview 6
PAGE 7
How to use GWS-CSCG Step 1: Power On/Off 1. Power On - Press button three times. On third press user must hold button down for 20 seconds. If successful: Power icon on reflecting battery charge status on display, green LED pattern and positive audio chime. If unsuccessful: Power icon reflecting insufficient battery on display, red LED light pattern and negative audio chime. 2. Power Off - Press button three times. On third press user must hold button down for 20 seconds.
PAGE 8
Step 2: NFC Tag Pairing Tap powered on Gateway to Tag and press the NFC button to pair the Tag to the Gateway.
PAGE 9
Step 3: Find shipment ID In the mobile app, find the unique shipment ID listed on the shipment document. Step 4: Review shipment info Confirm that the shipment information on the mobile app matches what is listed on the shipment document.
PAGE 10
Step 5: Pair Gateway Select “Pair Gateway “ and scan the Gateway barcode. Step 6: Pair Tags with shipping unit (i.e. Box, Pallet, Crate, Container) Select “Pair Tag with Shipping Unit” Scan the Tag barcode, then scan the Shipping Unit Label Barcode. Repeat the process for all Tags, then Click “Done” when done paining Tags with Shipping Units.
PAGE 11
Step 7: Attach Gateway to box, pallet or crate. Place the Gateway in the Gateway shipment sleeve and attach it to the box / pallet / crate. Step 8: Review shipment data & complete shipment. Review shipment details for accuracy. Once complete, the Gateway and Tag positions will be set (for recording Tilt) and can start collecting all sensor data.
PAGE 12
Step 9: Load shipment When loading pallets with Tags and Gateways onto a truck, try to place one pallet in the back of the truck, one pallet in the center of the truck and one pallet with the Gateway right by the door. Make sure that the Gateway faces the truck door, and is as close to the door as possible to ensure the Gateway signal can best maintain cell connectivity. Device Operation Please refer to software user gudie for device operation.
PAGE 13