Preface Copyright 2004 All Rights Reserved. The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer. In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages.
Notices Federal Communications Commission Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Highest SAR Value: 1.160W/kg Changes or modifications not expressly approved by the party responsible for compliance could void the user’ s authority to operate the equipment. Shielded interface cables and a non-shielded AC power cord must be used in order to comply with emission limits. This equipment is to be used with power supply: I/P: 100-240 Vac, 50-60Hz, 1.5A O/P: 19Vdc, 3.16A There is no internal power supply.
Canadian DOC Notice For Class B Computing Devices This Class B digital apparatus meets all requirements of the Canadian Interference - Causing Equipment Regulations. Cet appareil numerique de la classe B repecte toutes les exigences du Règlement sur le matèriel brouilleur du Canada.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Page intentionally left blank vi
Table of Contents Chapter 1: Before you Start -----------------------------------------------------------------------------------1 Conventions of This Manual ................................................................................................................................1 Things you must remember before working on your computer........................................................................
Introduction...........................................................................................................................................................43 Navigating through BIOS Setup ...........................................................................................................................43 Accessing the BIOS Setup Program....................................................................................................................43 The Menu Bar ......................
ix
Befo re y o u Start Conventions of This Manual Use this manual will help you get the most from your notebook computer. Ø If you are an experienced user of computers and/or Microsoft’s Windows operating systems, you might find it useful to read the Quick Start Guide that comes along with your accessories. Ø If you are a less experienced user, you should through the manual carefully before using your system.
8. 9. 10. 11. 12. 13. 14. 15. 16. 17. Place the power cord in such a way that people can not step on it. Do not place anything on top of the power cord. All cautions and warnings on the equipment should be noted. If the equipment is not use for a long time, disconnect the equipment from the main power outlet to avoid being damaged by transient overvoltage. Never pour any liquid into the opening, this could cause fire or electrical shock. Never open the equipment.
• • C. All components of the cord set must bear a “PSE” or “ T ” mark and registration number in accordance with the Japanese Dentori Law. The minimum specifications for the flexible cord are .75m ㎡ conductors. For Other Countries: • 18. 19. 20. 21. 22. The cord set fittings must bear the certification mark of the agency responsible for evaluation in a specific country. • The flexible cord must be of a HAR (harmonized) type H03VV-F. • The cord set must have a current capacity of a least 2.
3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 4 Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Versenden Sie Keine Flüssig- oder Aerosolreiniger. Am besten eignet sich ein angefeuchtetes Tuch zur Reinigung. Die Netzanschlußsteckdose soll nahe dem Gerät angebracht und leicht zugänglich sein. Das Gerät ist vor Feuchtigkeit zu schützen. Bei der Aufstellung des Gerätes ist auf sicheren Stand zu achten. Ein Kippen oder Fallen könnte Beschädigungen hervorrufen.
18. 19. 20. Landes, in dem Sie das Netzteil einsetzen, genügen, je nachdem, ob die Netzspannung 100120 oder 200-240V Wechselspannung beträgt. • Das Kabel-Set muss für das Land, in dem es eingesetzt wird, zugelassen sein. • Der Gerätestecker des Kabels muss in eine CEE22/ EN603/ IEC 320 Buchse passen. A. Für die USA und Kanada: • Das Kabel-Set muss UL-gelistet und CSA zertifiziert sein. • Die Minimalanforderungen für das Kabel entsprechen No. 18 AWG. B.
21. 22. Es besteht Explosionsgefahr, wenn der Akku nicht ordnungsgemäß ersetzt wird. Ersetzen Sie den Akku nur durch einen Akku gleichen oder äquivalenten Typs, der vom Hersteller empfohlen wird. Entsorgen Sie Akkus entsprechend den Anweisungen des Herstellers. Entfernen Sie den Akku auf keinen Fall bei eingeschaltetem Notebook, da hierdurch Daten verloren gehen könnten. Der Netzeingabeanschluss dient als Hauptschalter des Geräts.
There are some things you can tolerate that the computer can’t – things like static electricity, dust, water, steam and oil. In case you decide to pull over for roadside computing, try to choose a clean, comfortable work area for your system. A lithium-ion battery pack will be available when you are traveling. If you are running your system for the first time on battery power, remove the battery from the package, install it into the system and recharge the battery to fully prepare for service.
Page intentionally left blank 8
Intro ductio n There are more and more people spending large amounts of time in front of computer monitors now that scientists from many fields including anatomy, psychology, and occupational safety are involved in the study of ergonomically sound work environments. A few tips to help you work effectively without a lot of physical discomfort: Ø Purchase a chair with armrests and good back support. Don't slouch when sitting; keep your back straight.
Getting to Know Your Computer n Opening the LCD Panel At the front of the Notebook you will find a retaining latch on the display panel that locks the display in closed position when the Notebook is not in use. Ø Ø Ø Slide the display panel latch to the right until the display panel releases, and then raise the LCD screen. At any time you can tilt the display toward or away from you to a comfortable viewing position. Press on the Power button to start your computer.
With the LCD screen open, you will see several features important for operating your Notebook computer. Each of these features is briefly described below. 1. LCD Cover Release Latch 2. LCD Screen 3. Internet Explorer Button 4. Wireless LAN Button 5.
HDD Indicates that the computer is accessing the hard disk drive. Numeric Lock Indicates that the keyboard is in Num Lock mode. Caps Lock Indicates when the keyboard is in Caps Lock mode. In this mode, the keyboard produces uppercase text when you press a key. When you press the Caps Lock key again, the indicator goes off and the keyboard produces lowercase text. Scroll Lock Indicates when the keyboard is in Scroll Lock mode.
n The Left Side 1. 2. 3. 4. Ventilation Opening USB Port USB Port The LAN Port When using a LAN, please use an EMI Shielding Cable to minimize an inteference when transmitting.
5. The Modem Port Always disconnect all telephone lines from the wall outlet before servicing or disassembling this equipment. To reduce the risk of fire use only No. 26 AWG or larger telecommunication line cord. 6. Microphone Jack 7. Audio Line Out Jack LED Indicators These three LED indicators are separately program for the following functions: Power On, Suspend Mode and Battery Charge. 1. Power On 2. Battery Charge 3.
n The Right Side 1. The CD-ROM/DVD-ROM or DVD CD-RW Combo (Option) 2.
n 1. 2. 3. 4. 5. 6.
n 1. 2. 3. 4. 5.
Page intentionally left blank 18
G etting Started Connecting to a Power Source n Connecting the AC Adapter A universal AC adapter is provided to supply your computer with power and also charge the computer’ s battery pack. The adapter’ s AC input voltage can range anywhere from 100 to 240 volts, covering the standard voltages available in almost every country. The power cord for the AC adapter requires a three-hole grounded AC outlet.
Whenever possible, keep the AC adapter plugged into the Notebook and an electrical outlet to recharge the battery. Never turn off or reset your Notebook while the hard disk is in use and the HDD status icon is lit; doing so can result in loss or destruction of your data. Always wait at least 5 seconds after turning off your Notebook before turning it back on; turning the power on and off in rapid succession can damage the Notebook’ s electrical circuitry.
Only use batteries that are approved by an authorized dealer. All batteries are not the same and therefore should not be treated as such. Using the wrong battery could cause serious damage to your computer and yourself through toxic emissions. n Inserting and Removing the Battery Pack The battery pack should already be inserted in your Notebook computer when you unpack it. If not inserted, follow these directions: 1.
Ø Ø n Lift the release latch to release the battery from the bay. At this time the battery will now be angled slightly out of the bay. Hold the battery at the finger grip and lift it out of the compartment. Charging the Battery Pack The installed battery pack charges automatically any time the computer is connected to the AC adapter and an external power source. It is a good idea to occasionally discharge the battery pack fully to preserve its operating performance.
U sing the No tebo o k Co mputer Adjusting the LCD Screen Display The LCD screen display can be adjusted by the following key combinations. KEYS [Fn] + [F7] Decreases the brightness level. [Fn] + [F8] Increases the brightness level. [Fn] + [F10] Use this key combination to expand your video screen or reset to its original size. This function will be disabled when the system is in Overlay mode (playing video).
External CRT Display You can hook up an external monitor through the 15-pin CRT connector. Configurations are available: Ø LCD only Ø CRT only Ø Simultaneous display of the LCD screen and CRT monitor Ø TV only Ø Simultaneous display of the LCD screen and TV screen Ø Simultaneous display of the TV screen and CRT monitor You can switch between these display configurations by pressing the key combination [Fn] + [F12].
while keeping the keypad on an external keyboard activated, use the [Fn] + [NumLk] hot key on the Notebook keyboard. n The Notebook’s Hot Key Controls KEYS FUNCTION(S) Power Button Press this button once to power on or enter the suspend/resume mode. Press this button for more than 4 seconds to power off the system.
n TouchPad Precautions The TouchPad is a pressure sensitive device. Please take note of the following precautions. Ø Make sure the TouchPad does not come into contact with dirt, liquids or grease. Ø Do not touch the TouchPad if your fingers are dirty. Ø Do not rest heavy objects on the TouchPad or the TouchPad buttons. You can use the TouchPad with Microsoft Windows as well as non-Windows applications.
The CD-ROM/DVD-ROM/Combo Drive n Features of the CD-ROM/DVD-ROM/Combo Drive The features of the CD-ROM/DVD-ROM/Combo Drive are listed below. Ø The Audio Play feature allows you to play music CDs Ø Front panel load/unload button Ø Supports CD-DA, CD-ROM mode 1 and mode 2, Multi-Session Photo CD™, CD-I/Video CD (pcs.) Ø Low power consumption Ø 12.7mm height n Ø Ø Ø Ø Ø Ø n Precautions for Handling CD-ROM/DVD-ROM/Combo Drive Always hold the disc by the edges, avoid touching the surface.
2. 3. Push the eject button and pull the tray all the way out. Carefully pick up the CD disk by the edges and – while pressing down on the center ring – remove the CD-ROM/DVD-ROM/Combo from the tray. Do not insert any foreign objects into the disc tray. If you experience difficulty when ejecting the CD disk tray, stretch a paper clip (or use a pin or a thin metal rod) and insert it into the emergency eject hole located on the right side of the front panel. The CD disk tray should eject immediately.
To calibrate the battery pack follows the instructions below: 1. Insert the battery into the battery compartment and turn on the Notebook. If the battery is completely without power go to the next step. Otherwise, let the battery run down until the battery low-low warning beeps are heard. The system will automatically enter Suspend mode. 2. Turn the Notebook off. Connect the AC adapter and let the battery fully recharge. When the battery charge indicator turns off, the battery is fully charged. 3.
n Battery Low Warning When the pack initially reaches the “Battery Low” state approximately 10 ~ 15 minutes of the usable battery life is left. You will hear an audible beep signal every 1.5 seconds alerting you to the “Battery Low” status. When the battery power reaches the “Battery Low Low” status the beeping sound will accelerate. Your battery now has 1 ~ 2 minutes of battery charge remaining. You must save your data or connect AC power immediately; otherwise, you may lose your data.
n Adjusting the Brightness To adjust the brightness on the LCD screen, press and hold down the [Fn] key in the lower left hand corner of the keyboard and press the [F7] key to reduce the brightness or [F8] to increase the brightness.
Page intentionally left blank 32
D eskto p O peratio n Your notebook is capable of providing you with efficient and productive mobile computing, it also has the speed and capacity to service as a desktop system. This chapter discusses those functions of your notebook that are typical of desktop systems. Audio n The Multimedia Sound System The Notebook’ s built-in audio capabilities allow you to take advantage of a wide range of education and entertainment multimedia software.
n Audio Volume Control The Notebook is equipped with hot-key volume controls: Pressing the [Fn] + [F3] hot-key combination decreases the audio output volume, press the [Fn] + [F4] hot-key combination increases the audio output volume. n Audio Software Your notebook comes equipped with an integrated sound system capable of providing you with quality audio sound through the built-in speakers or through external speakers connected via the system ports.
The computer is equipped with several interface ports, including an enhanced parallel (printer) port, a serial port, and USB ports. These are provided as a means of connecting peripheral devices to the computer.
Page intentionally left blank 36
Internet Co nnectio n There are numerous ways to connect to the Internet. This may vary from the user’ s working environment as well as system specifications. Ø Using a modem and a telephone line Ø Using a wired LAN Ø Using a wireless LAN Using a modem for Connection to Internet Ø Ø Use a telephone line to connect to the modem port of your computer. Do not use a digital telephone line.
38 3. In the “Network Tasks” window, use your mouse pointer to click on the “Local Area Connection”. 4. Select “Properties” from the popup menu that appears 5. In the “This connection uses the following items” field, select “Internet Protocol (TCP/IP), and click “Properties”.
6. Enter the system’ s IP and DNS server addresses on the General tab of the “Internet Protocol (TCP/IP) Properties” window. If DHCP is used, click “Obtain an IP address automatically” and “Obtain DNS server address automatically” on the General tab.
7. After all the all the information are correctly entered in the “Internet Protocol (TCP/IP) Properties” window, click “OK” to finish. Using Both DHCP and Static IP for Connection to Internet When you are alternatively using networks with either DHCP or static IP addressing, you can use alternative settings that enable simultaneous configurations of DHCP and static IP to use both of the network connects without reconfiguring. 1.
4. 5. 6. button. Select the “Wireless Networks” tab and enable the “Use Windows to configure my wireless network Settings”. Click “OK”. A small icon will display on your lower right end of the Windows display. Click on the icon and select the setting for the available network shown on the list and click on the “Connect” button. For more detail on the Network key, please refer to your local ISP provider and follow the procedures describe in the “ISP Installation Guide” to proceed with the installation.
Page intentionally left blank 42
Running BIO S Setup Introduction The BIOS (Basic Input and Output System) Setup program is a menu driven utility that enables you to make changes to the system configuration and tailor your system to reflect installed hardware or alter system performance. When the Notebook is turned back on, the system is configured with the values stored in CMOS.
n Item Specific Help On the right side of the Setup screen is an area labeled Item Specific Help. This area will list navigation key shortcuts and information that is specific for the item that you are currently editing. The Menu Bar The top of the screen has a menu bar with the following selections: Main - Use this menu to make changes to the basic system configuration. Advanced - Use this menu to enable and make changes to the advanced features available on your system, such as enabling the FIR module.
→ Selects the menu item to the right. ↑ or ↓ Keypad arrow keys Moves the cursor up and down between fields. Tab Enter Moves the cursor to the next position available in the field. Minus key (-) Scrolls backward through the values for the highlighted field. Plus key (+) Scrolls forward through the values for the highlighted field. Home PgUp Moves the cursor to the field at the top of the window. End PgDn Moves the cursor to the field at the bottom of the window.
n Save Changes and Exit the Setup Program Refer to the Exit menu section of this chapter for detailed information on saving changes and exiting the setup program.
The Advanced Menu Selecting Advanced from the menu bar displays the Advanced menu: 47
The Boot Menu The Boot menu allows the user to specify the order in which the Notebook is to check for a device to boot the system. You can also configure the way that the system will boot up. To make changes, select Boot from the menu bar.
The Security Menu The Notebook’ s advanced system of security allows you to set a password to prevent unauthorized access to system resources, data, and the BIOS Setup Program.
The Exit Menu Once you have made all of your selections from the various menus in the Setup program, you should save your changes and exit Setup.
The So ftw are U tilities D isks AutoRun Installation Follow the step-by-step procedures on the CD-ROM/DVD-ROM to execute the “AutoRun” application by selecting the topic of “Driver Installation”. n Ø Ø Ø Ø Ø Ø n Ø Ø Ø Ø Ø Ø n Ø Ø Installing VGA Display Drivers Insert the CD-ROM Driver into your CD-ROM/DVD-ROM drive. Click “Start” and Select “Run”. Type the following: D:\Driver\VGA\Setup.exe (If D is not your CD-ROM/DVD-ROM drive, substitute D with the correct drive letter).
Ø Ø Ø Ø n Ø Ø Ø Ø Ø Ø n Ø Ø Ø Ø Ø Ø n Ø Ø Ø 52 Type the following: D:\Driver\LAN\Setup.exe (If D is not your CD-ROM/DVD-ROM drive, substitute D with the correct drive letter). Click on “Setup” to begin the Installation Wizard. Follow the Wizard’ s on-screen instructions to complete the installation. Restart the system. Installing the TouchPad Driver Insert the CD-ROM Driver into your CD-ROM/DVD-ROM drive. Click “Start” and Select “Run”. Type the following: D:\TouchPad\98&ME\Setup.exe D:\TouchPad\2K&X
Ø Ø Ø Double click on the "Other Devices" , double click the " Network Controller " and click on the "Driver" tab. Click the "Update Driver" tab and select the "Install from a list or specific location (Advanced)" item and click "Next". Select the "Include this location in the search" item and click on the "Browse" button and specify for the designate location of your CD driver D:\Wireless Lan\RALINK2_RT2500.
n 54 Gamma Correction
n Video Setting 55
n 56 Driver Mode Setting
Tro ublesho o ting This chapter describes locating and solving problems that you may encounter while using your computer. Locating a Problem Problems with your computer can be caused by something as minor as an unplugged power cord – or as major as a damaged hard disk. The information in this chapter is designed to help you find and solve minor problems.
To check the power cables, and connections: 1. If you have been using battery power, connect the Notebook to an external power source and make sure that the battery has a charge. 2. If you are using the Notebook with the AC adapter, check the power outlet, the power cord, and any power switches that may affect your computer. Ø Check the wall outlet or power strip with an item that you know is functioning properly. A lamp or radio is a convenient item for checking the power.
Ø Ø Error messages that indicate a failure with either the hardware, the software, or the Basic Input/Output System (BIOS). These critical malfunctions prevent the computer from operating at all or could cause incorrect and apparent results. An example of a critical error is microprocessor malfunction. Messages that furnish important information on the power-on and boot processes (such as memory status).
Solution: Check and make sure that you do not have a non-bootable floppy diskette inserted in your floppy drive. If your USB FDD is empty, you may not have an operating system installed on your drive. Contact technical support for assistance. Problem: You hear irregular beeps during operation of the Notebook and the system halts. Solution: The problem is beyond the scope of this manual. Contact technical support. Problem: An unidentified message is displayed.
Ø Ø Ø Check the cable connection. Check the mouse with another application to see if there is a software incompatibility problem. If possible, check the mouse with another computer to see if it works. If it doesn’ t operate on a different system, the mouse might be broken. Contacting Your Dealer If you still have a problem after reading the preceding sections, the next step is to contact your dealer. Your dealer can determine if the problem is something that requires the computer to be taken to the shop.
Page intentionally left blank 62
U pgrading y o ur Sy stem Upgrading your Memory Refer to the following instructions and illustration for information on upgrading your notebook's memory. Ø Turn off the computer and disconnect the AC adapter and all peripherals. Ø Turn the notebook over so that the rear ports are facing you and locate the memory module compartment. Ø Remove the screws that secure the RAM module compartment cover and set it aside in a safe place. Ø Remove the compartment cover and then angling it up and out.
The Easy to Upgrade HDD Module The hard drive in your notebook computer is made to be easily swapped out for upgrading. You should back up your hard drive before attempting o change the hard drive. Make sure that before you install a new drive, all the files in your system should be backed up. n Ø Ø Ø Ø Ø Ø Ø 64 To upgrade your Hard Drive Power down the system completely. Turn the system over with the front of the unit facing you.
Ø Ø Slide the compartment cover into place and be sure the screw holes on the cover align completely with the screw holes in the case. Secure the cover with the three screws.
Upgrading your System CPU Refer to the following instructions and illustration for information on upgrading your notebook's CPU Ø Turn off the computer and disconnect the AC adapter and all peripherals. From the rear side of your notebook, use your index finger to lift up the hinge cover attached to the LCD screen. Ø Ø 66 Bend your LCD screen into 90 degree angle then carefully lift up the hinge cover. Remove the screen that is attached to the keyboard in order to remove the heatsink on top of the CPU.
Ø Ø Remove all the screws attached to the heatsink. Before removing the screws, there are certain measures to followed in removing the heatsink Ø Ø To remove the heatsink, first loosen the screw carefully. After loosening one screw, be certain that the next to be loosen should be the screw on its adjacent side as shown on the illustration. Be sure to loosen all the screws first before removing it totally to release the heatsink. Failure to do so will cause a major damage to the heatsink.
Page intentionally left blank 68
Specificatio n Detailed Notebook Specifications Processor Ø Ø Operating System Compliance Ø Ø Core Logic Ø Memory Ø Ø LCD Display Ø Video & Graphics Ø Ø Ø Intel® Celeron® M (Banias) processor, 512KB L2 cache, FSB400MHz 479pin mFCPGA Package Microsoft® Windows ® XP Professional Edition Microsoft® Windows ® XP Home Edition SiS 661 + 963L Expansion 2 slots of 200pin DDR SO-DIMM SDRAM module, expandable up to 2GB system memory Support 3.3V DDR-266/333/400 SDRAM Module 14.
Keyboard Ø 3.0mm travel, inverted-T, 88 keys with windows key Interface Ports Ø For Connectivity Left Side Ø Right Side Ø Mic-in, Headphone Jack with adapter for 5.1 channel SPDIF out support, Modem port, LAN port, USB 2.0 port*2 DC -in jack Rear Side Ø USB 2.0 portx2, TV-out connector, CRT connector, parallel port Ø Audio Controller: integrated chipset, Audio Codec : CMedia 9761 AC97 2.1, SPDIF & 5.1 channel support Built-in two stereo speakers Input: 100-240V AC, 50-60Hz, 1.
Weight Ø 2.6 kg with 14.