In-Ceiling Electric Motorized Front Projection Screen Evanesce Tab-Tension Series User’s Guide Rev.12/2/2014-EA info@elitescreens.
Important Safety & Warning Precautions Make sure to read this user’s guide and follow the procedure below. Caution: The screen’s Black Top Drop is already set to its maximum drop distance. There is NO extra Black Top Drop in the roller. Please be aware of this as it will void your warranty with Elite Screens. Unapproved changes or modifications (except for cutting the power cord for hardwire installations) to this unit are prohibited and will void your warranty.
Installation Warning Due to various installation environments, the instructions provided in this user’s guide are for reference only. Please consult a professional installation company for further installation and safety advice. The installer must insure that proper mounting hardware is used to provide adequate strength suitable for the installation. Elite Screens is not liable for any faulty installations.
Accessories for Evanesce Tab-Tension Series Please make sure all accessories listed below are included before proceeding. A. IR Remote B. RF Remote C. 3 Way Wall Switch D. IR Eye Receiver G. AAA Batteries Red+ E. 12V Trigger Rev.12/2/2014-EA GreenF. In-Wall RJ-45 Module info@elitescreens.com H.
Control System for Evanesce Tab-Tension Series RJ-45 INPUT FOR 5-12V TRIGGER 1. 5-12V Trigger: The built-in 5-12V trigger input allows your screen to synchronize its drop & rise with the projector’s power cycle. The screen deploys when the projector powers up and will retract when the projector powers down. The 512 volt adaptor connects to your projector’s trigger output via a separate cable that may or may not be provided by the manufacturer of the projector.
. In-Wall RJ-45 Module: The RJ-45 Module connects to a local wall switch for UP/Down control of your screen. Please follow the picture diagram below for instructions on how to connect the accessory. Elite Screens In-Wall Switch Module ( ZIW-Module ) Ethernet (RJ45) network cable (not included) Local Wall Switch In-Wall UP/DOWN Switch Module (ZIW-Module) Elite Electric Motorized Screen Steps to attach Elite Screens Motorized Screen to your local wall switch 1.
Hardware Parts List for Evanesce Tab-Tension Series Please make sure all parts listed below are included before proceeding with the installation. G Hardware Parts List A. Case Rail Nut B. Hex Screw C. Hanging Bracket D. Suspension Bar E. Washer F. Hex Nut QTY 4-6 4-6 2-3 4 8-10 4-6 G. Suspension Bar J- Hook 4 Installation Instructions Please consult a professional installer. Elite Screens is not liable for faulty installations. Power 1.
Assembly 2. Insert the Hex Screw (B) through the Hanging Bracket’s (C) screw hole and secure with the Case Rail Nut (A). Slide the Hanging Bracket (C) through the railing on top of the case. 3. Place the Suspension Bar (D) on the Hanging Bracket (C) and align with the hole as shown below. Secure the Suspension Bar (D) with the Hex Screw (B), Washer (E) and the Hex Nut (F). Install the Suspension Bars (D) to your ceiling according to their distance. B D Rev.12/2/2014-EA info@elitescreens.
Optional Suspension Bar J-Hook (G) 1. Attach the Suspension Bar J- Hook (G) to the bottom of the Suspension Bar (D) and secure with the Hex Screw (B), Washer (E) and Hex Nut (F). F E E B 2. Attach the Suspension Bar J-Hook (G) to the Hanging Bracket (C) as shown in figure below. Install the Suspension Bars (D) to your ceiling according to their distance. G C Rev.12/2/2014-EA info@elitescreens.
Optional Installation (parts & hardware not included) 1. Place the Hanging Bracket (C) in the desired location on the screen’s housing and measure the distance as shown below. (L = Distance) 2. Mark the location of where the screen will be installed according to the distance (L) and then secure the bolt to the ceiling. 3. Install the screen to the screw bolt as shown in the figure below. Rev.12/2/2014-EA info@elitescreens.
Evanesce Tab-Tension Series Dimensions Table Unit: mm Model Nominal Diagonal View Width (A) Case (A1) Length (A2) (A3) (A4) (A5) View Top Height Border (B) (B1) (B2) Case H (B3) Overall Height (B4) Case (B5) Width (C) C1 C2 C3 C4 ITE100VW2-E8 100"(4:3) 2032 95 2347 2407 1947 2342 1524 203 1827 118 1945 100 98 50 925 145 180 ITE120VW2-E8 120"(4:3) 2438 95 2770 2830 2370 2765 1828 203 2131 118 2249 100 98 50 925 145 180 ITE100HW2-E8 100"(16:9) 2214 95 2530
Below ceiling installation instructions Please make sure all parts listed below are included before proceeding with the installation. Hardware Parts List for below ceiling installation A. End Flange x 2 B. Hanging bracket x 2 C. Threaded rod x 4 D. Socket wrench x 1 E. M8x16mmx1.5mm washer x 28 F. M8 nut x 20 G. M8 Top expanding bolt x 4 H. M8x40mm hex screw x 4 1. Measure and cut the ceiling installation slot: The width should not exceed 100mm and not less than the width of the screen’s housing.
4. Insert the threaded rods (C) through the M8 expanding bolts and then attach the M8x40mm hexagonal screws with the washer (E). Last put the Hanging Bracket (B) through the threaded rod equal to the height of the screen’s housing. Once they are firmly in place (as shown below) make sure that they will hold the weight of the screen. E and F L (A4) B C C Ceiling 5. Push the screen up into the space. Use the threaded rods (C) to attach the screen assembly to the ceiling.
Limited Warranty Policy What is Covered: Elite Screens, Inc. (“Elite Screens”) warrants its products to the first retail purchaser, if purchased new and operated in the United States or Canada, to be free from defects in workmanship and materials (except as provided below) for a period of (2) years from the date of original purchase, and (3) years for products purchased directly by educational, non-profit, religious or government organizations.