Always Connected. Always Covered.
Preface As this is the full User Manual, a working knowledge of Z-Wave automation terminology and concepts will be assumed. If you are a basic user, please visit www.domeha.com for instructions.
Table of Contents Preface. . ................................................................................................................................ 2 Description & Features. . .................................................................................................... 4 Specifications. . .................................................................................................................... 5 Physical Characteristics..............................................................
Description & Features SolidWorks Student Edition. For Academic Use Only. The Dome Water Main Shut-Off is a Z-Wave Plus Certified device that installs over any standard 1/2” to 1-1/2” ball valve, and opens or closes the valve when given a signal. The Water Main Shut-Off consists of three main parts the “MOTOR ASSEMBLY,” the “MOUNTING BRACKET,” and the “CONTROL ARM.
Specifications Technical Specifications Radio protocol Z-Wave(500 series) Power supply 12VDC Power Consumption 0.13W Working current 35mA Operating temperature Radio frequency Range Dimensions (L x W x H) 32 - 112 °F 908.4 MHz US Up to 150’ depending on environment 2.5” x 3.
Physical Characteristics The names used in Figures 1 & 2 will be used throughout this manual. Please refer to this page as needed. LED Indicator Control Arm Open/Close Button Motor Assembly Mounting Bracket Figure 1 - Main Parts of the Water Main Shut-Off SolidWorks Student Edition. For Academic Use Only.
Inclusion & Exclusion Inclusion Follow the instructions for your Z-Wave Certified Conto enter inclusion mode. When prompted by the controller: CAUTION Upon inclusion, the motor will engage and start turning automatically. To avoid serious injury, keep your fingers and hands clear of the CONTROL ARM and its path, only gripping the unit firmly by either the MOUNTING BRACKET or the top of the MOTOR ASSEMBLY 1. Plug the Water Main Shut-Off into an outlet 10’ from your controller.
Factory Reset & Misc. Functions Resetting the Water Main Shut-Off If needed, the Water Main Shut-Off can be reset locally by following these steps. Only do this when your Z-Wave controller is disconnected or otherwise unreachable. Beware that resetting your device will disconnect it from your system: 1. Press and hold the OPEN/CLOSE BUTTON for at least 10 seconds then release. 2. The Water Main Shut-Off’s memory will be erased to factory settings. 3. A flashing light indicates a successful factory reset.
Physical Installation Review the Pre-Installation Checklist below to make sure the Water Main Shut-Off can be used for your application. The device should already be included in your Z-Wave system before continuing further.
Installation Process 1. Make sure the installed valve is comfortably usable by hand before continuing further. 2. Open both HOSE CLAMPSs completely so their ends are free, insert both of them into the slots in the MOUNTING BRACKET, and let them hang loosely. 3. Remove the protective film covering the screws on the CONTROL ARM and spread the CONTROL ARM. 4.
Centers are aligned Figure 6 - Proper Alignment of the Water Main Shut-Off ball valve, and tighten the HOSE CLAMPS until the Shut-Off is completely secure (Figure 5.) 7. Squeeze the CONTROL ARM closed around the valve handle and secure it CAUTION It is absolutely critical that the axes for both the valve and Water Main Shut-Off are aligned. Improper installation will result in unreliable performance. Examine Figure 5 for more details and please visit www.domeha.
LED & Button Behavior Color Blue Behavior This happens when… Blink Continuously …the device is not yet included in a Z-Wave Network. On Continuously …the device is included in a Z-Wave Network and is in the “Closed” position. Off Continuously …the device isincluded in a Z-Wave Network and is in the “Open” position.
Compatible Command Classes Command Class Notes Device Reset Locally V1 (5A) - Powerlevel V1 (73) - Association Group Information V1 (59) Returned Value: 01 05 00 0F 00 0F 00 Z-Wave Plus Version: 01 Z-Wave Plus Info V2 (5E) Role Type: 05 (Slave—Always On) Node Type: 00 (Z-Wave Plus Node) Installer Icon Type: 0F 00 (Generic Relay Device) User Icon Type: 0F 00 (Generic Relay Device) Returned Value: 06 04 05 00 02 02 00 Z-Wave Library Type: 06 Version V2 (86) Protocol Version: 04 05 Protocol Sub-Version
Command Class Notes Group 1 Group 1 is the “Lifeline” group, which can hold five devices. The Water Main Shut-Off sends this group a Binary Switch Report whenever Association V2 (85) it is turned on or off. The Water Main Shut-Off also sends this group a Device Reset Locally notification to remove itself from the Z-Wave network. Binary Switch commands will open and close the Water Main Shut-Off. Binary Switch Report commands are also used to communicate changes in device status (e.g.
Troubleshooting Q Q: Help! My Water Main Shut-Off paired successfully, but my controller can’t see it anymore after I installed it! A A: First, make sure your battery didn’t come loose during set-up. Otherwise, the Z-Wave signal is probably weak in that area of your home. Remember that the 120' - 150' range doesn’t take into account walls, furniture, and other obstacles.
Warranty & Support If you have questions, our trained Customer Service Department is happy to assist you 24 hours a day, 7 days a week. Contact Dome Customer Service as follows: • In North America dial: 1-855-249-1754 • Email Dome at support@domeHA.