MemoTec-915 elero USA 10827 Alder Circle USA-Dallas Texas 75238 info@eleroUSA.com USA Operating instructions Please keep these instructions in a safe place ! elero GmbH Antriebstechnik Linsenhofer Str. 59–63 D-72660 Beuren info@elero.de www.elero.com 309103 01 Nr. 18 100.
Contents USA-1 USAUSAUSAUSAUSAUSAUSA- 2 3 4 5 5 6 7 USA- 7 USA- 7 USA- 8 USA- 8 USA- 8 USA- 9 USA- 9 USA- 10 USA- 11 USA- 11 USA- 11 USA- 12 USA- 12 USA- 12 USA- 12 USA- 13 USA- 13 USA- 13 USA- 14 USA Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Instruction to the user . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Explanation of buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Explanation of buttons This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Installation General information Wall holder installation The MemoTec-915 operates your drive at the programmed switching times. Note: Radio base stations transmitting in the same frequency range may cause reception interference. The MemoTec-915 device can be operated manually at all times. USA General information/Designated use Please note that the operating range of the radio signal is limited by legislation as well as by the product design.
Explanation of functions Explanation of functions 24 hr button Manual/Automatic sliding switch When the sliding switch is set to MANUAL , only manual control commands are executed. When the sliding switch is set to AUTO , manual and automatic control commands are executed (time). The 24-hour button can be used to programme one UP and one DOWN command. These commands are then automatically executed every 24 hours. Control light The control light flashes 3 times to confirm switching time settings.
Programming additional transmitters Programming radio channel settings Programming additional transmitters Programming transmitter/channel To programme additional transmitters in one receiver, please proceed as follows: Prerequisite: The drive must be installed. 1. With pre-installed receivers, the fuse must be disconnected and reconnected after a few seconds. The receiver will then remain in programming mode for approximately 5 minutes. 2.
Intermediate position Roller shutter/venetian blind Intermediate position roller shutter/venetian blind Adjustment Pos B Prerequisite: The transmitter has been programmed. 1. Press the DOWN button twice in quick succession. 2. The drive will adjust the shutter curtain/venetian blind into the stored intermediate position. If no intermediate position is stored, the shutter curtain/venetian blind is automatically adjusted into the lower limit position.
Programming daily control commands Deleting individual transmitters Programming daily control commands One UP and one DOWN control command can be programmed for each day of the week. These commands are automatically repeated every 24 hours. If the same function is programmed twice, the old switching time is automatically overwritten. Disconnect the fuse – and reconnect after a few seconds. 1.
Programming weekly control commands/ Technical data/Battery replacement Programming weekly control commands Deleting weekly control commands Weekly switching times settings can be made for every day of the week. The weekly control commands are not deleted if a daily control command is changed. 1. To delete all weekly control commands, press the week programming button for 5 seconds or longer. The control light will flash 3 times briefly to confirm.
Warnhinweise USA Cleaning/Troubleshooting/ General declaration of conformity Cleaning Clean the device with a damp cloth only. Do not use a cleansing agent as doing so may damage the plastic. Troubleshooting Problem Cause Remedy Drive is not functioning. Faulty connection. Check connection. Drive moves in the wrong direction. Faulty connection. Exchange V and B wires in the power supply unit. MemoTec-915 does not execute the programmed control commands. Sliding switch is set to manual mode.