Combio-915/120 V Combio-915 JA 285000906 Combio-915 RM 285200906 elero Bedienungsanleitung Bitte bewahren Sie die Bedienungsanleitung auf ! Operating Instructions Please keep the instructions in a safe place. PT Instrucciones de servicio ¡Por favor, conserve estas instrucciones de servicio! PT Instruções de serviço Por favor conserve as instruções em lugar seguro. elero GmbH Antriebstechnik Linsenhofer Str. 59–63 D-72660 Beuren Tel.: +49 (0) 7025-13-01 Fax: +49 (0) 7025-13-212 www.elero.
Safety tips USA CA Contents Safety tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . USA/CA- 2 Important safety indications! Observe the following Instructions. General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . USA/CA- 3 Use in accordance with the regulations . . . . . . . . . . . USA/CA- 3 Optimal use of the radio signal . . . . . . . . . . . . . . . . . USA/CA- 4 Mounting options . . . . . . . . . . . . . . . . . .
regulations Optimal use of the radio signal USA CA General/Use in accordance with the General information Optimal use of the radio signal The Combio-915 JA/RM radio receiver allows the extension of alternating current drives to a radio drive. • Do not bend the antenna. Use in accordance with the regulations • If reception is poor, adjust the antenna. The Combio-915 JA/RM can only be used for controlling roller shutters and sun protection systems such as venetian blinds.
Combio-915 JA Mounting options Combio-915 JA for venetian blind drives (28 500.0001) Combio-915 JA 1. Put the Combio-915 into the mounting clamp. Combio with clip 2. Fasten the Combio-915 JA + clamp to the inside or outside of the channel. USA CA Mounting options The Combio-915 JA is suitable for the use with venetian blind drives. In order to carry out an exact slat tilting, the Combio-915 JA has a dead-man operating mode.
Connection and installation (Combio-915 JA) Combio-915 RM for tubular motors (28 520.0001) Combio-915 JA for venetian blind drives The Combio-915 is suitable for the use with tubular motors for roller shutters and sun protection systems. If a command is sent, the receiver immediately activates the selflocking operating mode. The hand-held transmitter can be used to program an intermediate position.
Connection and installation (Combio-915 The Combio-915 RM for elero tubular motors with plug-in cable (limit switch drive) Combio-915 RM for tubular motors with plug-in cable (ACS-E electronic drive) 1. Switch off the mains voltage. 1. Switch off the mains voltage. 2. Press the locking mechanism of the drive plug towards the cable with a screwdriver. 3. Pull out the plug. 3. Pull out the plug. 4. Plug the motor cable of the radio receiver into the drive. 5.
Connection and installation (Combio-915 RM for CSM-E) Combio-915 RM for tubular motors with fixed cable (limit switch drive) Combio-915 RM for elero tubular motors with fixed cable (CSM-E electronic drive) for textile sun protection. 1. Switch off the mains voltage. Note: CSM-E drives must not be connected using the connector located on the Combio-915 RM. 2. Cut off the plug of the radio receiver. 3. Prepare the cable for connection (remove cable jacket and strip). 4.
Technical data EC-Declaration of conformity E C - D E C LARAT I O N O F C O N F O R M I T Y Combio-915 JA Combio-915 RM (venetian blind drives) (tubular motors) Nominal voltage 120 V 120 V Frequency 60 Hz 60 Hz Max.