UniTec-868, UniTec-915 Nr. 28 330 0006, Nr.
Contents Contents Warning advice Device explanation.......................................................................3 Safety instructions.......................................................................4 Safety instructions/Exclusion of liability ..................................4 Scope of supply/General information........................................6 Intended use.................................................................................6 Safety instructions for radio operation....
Device explanation Safety instructions / Exclusion of liability Warning advice Hand-/Automatik- Safety instructions: STOP! Kontrollleuchte UP button Manual/ automatic sliding switch STOP button Alarm signal control light DOWN button UniTec-868 Programming buttons P (all-purpose) P 5HVHW 7DVWH 4 | EN 5HVHW K ZHHN 3RV • T he operator must ensure that the basic safety measures are observed and fulfilled.
General safety instructions CAUTION! Observe the following safety instructions! Failure to observe them can lead to bodily injuries! General • N ever install or use damaged products. • O nly use unmodified original elero electrical parts. • I f the device is opened without permission or used in an improper manner, or if it is incorrectly installed or operated, there is a risk of damage to persons and property. • The device contains small parts which can be swallowed.
Instructions for radio operation Mounting ofadvice the wall bracket Warning Safety instructions for radio operation Mounting of the wall bracket CAUTION! bserve the following safety instructions for radio O operation! Only use radio systems, if they are allowed and can be operated without interference. • P lease note that radio systems must not be operated in areas with an increased risk of interference (e. g. hospitals, airports, ...).
Explanation of functions Explanation of functions Warning advice Explanation of functions Note Bidirectional radio system A bidirectional radio system transmits radio signals to radio receivers and enables feedback to the transmitter. The radio signal can be sent directly to the target receiver. If this is not possible, then the radio signal is forwarded via other bidirectional participants until the signal reaches the target receiver.
Explanation of functions Explanation of functions Group control Status display Operating mode display orange green Transmitter functions bidirectionally, Operating mode Automatic orange red Transmitter functions bidirectionally, Operating mode Manual green green Transmitter functions unidirectionally, Operating mode Automatic green red Transmitter functions unidirectionally, Operating mode Manual 3 x orange /red green Transmitter functions bidirectionally, Operating mode Automatic, Transm
Explanation of functions Hand-/Automatik- Programming a transmitter / channel Kontrollleuchte Note Programming a transmitter/channel ! When switching on the automatic, an upward travel of the receiver is triggered (provided that sensors are programmed in the receiver). The receiver must be installed. End position 1. Disconnect the fuse - and reconnect after a few seconds. The receiver is now in programming mode for about 5 minutes.
Programming additional transmitters/chanels Programming additional transmitters/channels Warning advice Programming additional transmitters/channels Programming additional transmitters NOTE! If several receivers are connected to the same feed line, then all are simultaneously in programming mode. The shutters/blinds start a brief “random” up/ down travel. The longer you wait with the programming, the greater will be the offset.
Intermediate positions for roller shutter/awning/venetian blind Intermediate positions for advice rollerWarning shutter/awning/venetian blind Roller shutter Pos ▼ Intermediate position Pos ▲ Ventilation position Awning Venetian blind 2. Press the STOP button in addition. The shutter/blind stops. You have programmed the position ventilation slots/tilting/fabric tightening.
Intermediate positions for roller shutter / awning / venetian blind Deleting Pos ▼ (intermediate position) ! PREREQUISITE! The transmitter is programmed. Approaching the end positions roller shutter / awning / venetian blind ! PREREQUISITE! The transmitter/transmitter channel is programmed. The end positions of the drive have been set. 1. Press simultaneously: • DOWN button • STOP button 2. Hold down this button combination for approx. 3 seconds. The status LED lights up briefly.
Deleting a transmitter / Technical data Warning advice Changing the batteries/ cleaning / disposal Deleting a transmitter/channel Replacing the battery 1. Press the STOP button and also the programming button P (below the cover). 2. Hold down this button combination for approx. 6 seconds until the status LED briefly lights up orange and then red. In unidirectional operation, the status LED briefly lights up green twice and then red, within these 6 seconds. Deleting all transmitters 1.
Notes on repair/repair address Warning advice Notes on troubleshooting Notes on repair Please contact us, if you are unable to eliminate a problem. When contacting our service team, please always state the item description and number from the type plate (back of device). – Item number – Item description – Type of fault – Circumstances – Own assumption – Preceding unusual occurences 24 | EN Fault Cause Remedy Drive does not run, 1. The battery is empty. 1. Insert new Transmission Battery.
EC Declaration of conformity Warning advice Certification FCC / IC EC declaration of conformity elero GmbH hereby declares that the UniTec-915 complies with the basic prerequisites and the other relevant provisions of the EC directives. The complete declaration of conformity can be found in the download area of our website. Certification FCC / IC US: Addendum to the manual FCC / IC approval This device (UniTec-915) complies with part 15 of the FCC Rules and RSS-210.
elero GmbH Antriebstechnik Linsenhofer Str. 65 D-72660 Beuren Fon: +49 7025 13-01 Fax: +49 7025 13-212 info@elero.de www.elero.com We reserve the right to make technical changes.
