TempoTel 2 867/868/915 MHz 28265.0002, 28266.0002, 28267.0002, 28265.0902, 28266.0902, 28267.
Contents Contents Contents Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Safety instructions for radio operation . . . . . . . . . . . 5 Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Exclusion of liability . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Scope of supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Mounting of wall bracket . . . .
Safety instructions Safety instructions for radio operation Safety instructions Observance of these instructions is a precondition for safe and fault-free operation and for the product performing as intended. • The operator/user shall have read the instructions fully and understand them. • The operator shall ensure that the instructions are available to the user in a legible form. • The operator shall ensure that all safety measures are observed and complied with.
Intended use Mounting of wall bracket Intended use Weight in grams (including battery) The TempoTel 2 is a multi-channel transmitter. This can be used unidirectionally (compatible with the existing ProLine program) or bidirectionally. The hand-held transmitter should only be used for controlling roller shutters, Venetian blinds and sun protection systems which are fitted with elero radio receivers. Other uses or use going beyond this is considered to be contrary to the intended use.
Description of the device Explanation of functions Description of the device Explanation of functions Front side of the device Bidirectional radio system 1 Display 2 Left menu button 3 Right menu button 4 Joystick 5 Operating mode indicator 6 UP button 7 STOP button 8 Status indicator 9 DOWN button 10 Select button A bidirectional radio system transmits radio signals to a radio receiver and enables feedback from the radio receiver to the transmitter.
Explanation of functions Explanation of functions Note Program Factory settings Individual Off Open 07:00 / Sat + Sun 08:00 Close 20:00 Settings according to channels are only available if at least one channel has been programmed. Astro On Notice: Confirming “Factory settings” in the menu FUNCTION restores all the internal settings of the hand-held transmitter to the factory settings (“Settings”, “Program”) except the setting for deleting the channel.
Explanation of functions Status indicator Flashing orange Flashing orange rapidly Orange then green Orange then flashing red Red then green Red then flashing red Green Green with repeat, then red (unidirectional) Alternating orange and green (or red), then red (bidirectional) Flashing red Explanation of functions Meaning Channel (sender) not taught-in into any receiver Channel (transmitter) in bidirectional programming mode. Operation of already programmed receivers is not possible.
Explanation of functions Explanation of functions Display in operating mode Note In unidirectional channels, only the automatic system for timed switching functions in the transmitter is switched off when these are in manual mode. The automatic shading system stays switched on in unidirectional receivers. In the case of bidirectional channels all the automatic functions in the receivers are switched off in manual mode.
Explanation of functions Explanation of functions Menu mode Menu structure Menu structure Date/Time Program Channel selection Individual Astro Astro evening Switching time off Administration Channels Settings Room-specific allocations Groups Group allocations Holiday Astro Lighting Summer/winter time Channel settings 16 | EN Factory setting You can make selections and changes in the menu using the left and right menu buttons and the joystick.
Explanation of functions Explanation of functions Lock time PROGRAM menu Once you have selected the channel, you can set different switching times: • Individual (each day can be selected) • Astro (each day can be selected), set ON at the factory • Astro evening (each day can be selected) The selection of the switching or lock times assigned to days is performed using the activation of the days of the week using the joystick (up/down).
Explanation of functions Explanation of functions Submenu Lighting SETTINGS Menu Switching the display background lighting on and off Adjusting the functions as required. Settings for holidays, Astro, language, lighting and Summer/ Winter time apply to all channels. Submenu SU/WI time Submenu holiday The holiday function simulates an occupied house while you are on holiday. If this function is active, all the programmed switching times are delayed by 0 to 30 minutes at random.
Explanation of functions Explanation of functions Product selection After selection of a channel, a product-specific designation of individual functions and a maximum running time can be assigned to the channel. Product-specific basic characteristics of Venetian blind products as compared with other product groups are recognised and configured automatically. Approach of the ventilation or tilting position (according to the preset running time): short double press of the UPbutton.
Explanation of functions Explanation of functions Priority Once you have selected a channel, you can set an activated priority, which means that automatic time switching commands from the hand-held transmitter channel are given priority in all receivers and accepted even the MANUAL operating mode of receivers. Automatic switching commands are prioritised in the factory settings. The activated prioritisation of timed switching commands is indicated in the function bar of the display by a "P".
Explanation of functions Explanation of functions Programming additional transmitters SRV Service information. Note Submenu version Indication of the current firmware version. Programming the transmitter Requirement The receiver is installed. Check whether the channel has been deleted or is in the correct mode according to the status display. Stand in front of the curtain to be programmed while programming. 1.
Explanation of functions Explanation of functions 4. Press the DOWN button as soon as the curtain starts moving in downwards direction (within 1 second at the most). The status indicator is lit briefly. The curtain stops. The transmitter channel has been programmed. 4. Press the DOWN button as soon as the curtain starts moving in downwards direction (within 1 second at the most). The status indicator is lit briefly. The curtains stop moving. The transmitter channel has been programmed.
Explanation of functions Explanation of functions Press the UP button only briefly (jog mode on JA, pulse mode for Combio Pulse), the curtain starts briefly and stops again. Intermediate positions of the curtains Roller shutter Awning Venetian blind Interior shading • Move the curtain in the UP direction using the UP button until the ventilation slots open, or the slats have turned. Keep pressing the UP button during operation. Also press the STOP button. The curtain stops.
Explanation of functions Replacing the battery Operation of the transmitter using Combio JA Pulse lights for 6 seconds: first green briefly twice and then red. The channel in the transmitter is also deleted. A Combio 867/868/915 JA Pulse can be used for the precise adjustment of the slats for Venetian blind drives. The preset pulse time of Combio Pulse is cycled by pressing the UP or DOWN button. Deleting all transmitters from the receiver The pulse time can be changed by the user.
Cleaning EC declaration of conformity Cleaning EC declaration of conformity Clean the unit with a damp cloth. Do not use any cleaning agents or solvents. This may attack the plastic. elero GmbH hereby declares that the TempoTel 2 complies with the basic prerequisites and the other relevant provisions of the EC directives. The complete declaration of conformity can be found in the download area of our website.
Troubleshooting Repair Troubleshooting Fault Cause Remedy Drive does not run; status display does not light up 1. Batteries are exhausted 2. Batteries are incorrectly installed 1. Insert new batteries 2. Insert batteries correctly Drive does not run; status display lights up red or flashes orange Unidirectional: Status display lights green 1. The receiver is outside radio range. 2. Receiver not operating or faulty 3. Receiver not yet programmed 1. Reduce distance to the receiver 2.
Manufacturer's address Contents Manufacturer's address elero GmbH Antriebstechnik Linsenhofer Straße 65 72660 Beuren Deutschland / Germany Tel: +49 7025 13-01 Fax: +49 7025 13-212 info@elero.de www.elero.com Please visit our website if you require a contact outside Germany.
www.elero.