User's Manual

EL-2640
The EL-2640 is a wireless keypad designed for use
with the infiniti control panel. This keypad includes
three arming keys that activate Full, Part or
Perimeter arming modes. Pressing the Full and
Perimeter buttons simultaneously generates an SOS
panic alarm. Additionally, two Home Automation
keys allow remote control over Home Automation
modules.
Registration
To register the EL-2640:
1. Set the control panel to Registration mode.
2. Press a button on the keypad making sure
that the LED lights up when the button is
pressed.
3. Wait for five seconds and press the same
button again.
Battery Replacement
Every time a key is pressed, the battery status LED is lit.
When the battery needs to be replaced, the LED
flashes.
To replace the battery:
1. Remove the battery cover located at the rear of the unit. To do so, press the release tab using a small
screwdriver and lift the cover away from the EL-2640’s plastic housing.
2. Observing correct polarity, replace the 9V alkaline battery.
3. Replace the battery cover making sure that it clicks shut.
Wall Mounting
To mount the EL-2640 to the wall:
1. Place the mounting bracket in position against the wall and
mark the two mounting holes.
2. Install wall anchors in the appropriate positions and mount the
bracket to the wall.
3. Place the EL-2640 in the bracket and slide it down until you
hear a click.
4. To release the EL-2640, press the release tab in the direction of
the wall and remove the unit.
Technical Specifications
Antenna: Built-in Whip
Frequency: 418MHz FM
Current Consumption: 25mA (transmission), 3µA (standby)
Power: 9V Alkaline Battery (Eveready 522)
RFI Immunity: 40V/m
Operating Temperature: 32-140°F (0 to 60°C)
Dimensions: 5”H X 1.9”W X 1.1”D (128 x 49 x 27mm)
FCC ID: RIYEL2640
Figure 2: EL-2640 Mounting Bracket
Figure 1: EL-2640
(front and rear view with battery cover removed)
9V
Top
Mounting
Hole
Bottom
Mounting
Hole
Release
Tab
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequenc
y
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna, 2. Increase the separation between the equipment and the receiver, 3. Connect the equipment into an outlet on a
circuit different from that to which the receiver is connected, 4. Consult the dealer or an experienced radio/TV technician for help.
Warning: Changes or modifications to this equipment not expressly approved by the party responsible for compliance (Electronics Line 3000 Ltd.) could void the
user’s authority to operate the equipment.
Electronics Line 3000 Ltd.: 2 Granit Street, Kiryat Arieh, POB 3253, Petah Tikvah 49130 Israel. Tel: [phone], Fax: [phone]
USA: 5637 Arapahoe Avenue, Boulder, Colorado 80303. Tel: [phone], Fax: [phone]
UK: Unit 7, Leviss Trading Estate, Station Road, Stechford, Birmingham B33 9AE. Tel: [phone], Fax: [phone]
France: ZI-61, rue du Marché Rollay, 94500 Champigny-Sur-Marne. Tel: [phone], Fax: [phone]
ZI0313A (11/03)
A
ll data is subject to change without prior notice. In no event shall Electronics Line 3000 Ltd. (EL3K) be liable for an amount in excess of EL3K.’s original selling price o
f
this product, for any loss or damage whether direct, indirect, incidental, consequential or otherwise arising out of any failure of the product.