User's Manual

EL-2620
The EL-2620 is a wireless keypad for use with the infiniti control
panel. This keypad is primarily designed as an additional arming
station, including three arming keys that enable Full, Part or
Perimeter arming modes. Pressing the Full and Perimeter buttons
simultaneously generates an SOS panic alarm. Additionally, the
keypad may be used to control Home Automation modules.
The Cancel key,
, clears the keypad in the event that a key is
pressed by mistake while entering a code, for example. This key
causes the keypad to disregard what was previously entered
enabling the user to start again.
A slide-out reference card on the rear of the keypad can be used for
writing down essential information such as Home Automation module
allocation.
Note: Do not write user codes on the reference card!
Registration
To register the EL-2620 to the receiver:
1. Set the receiver to Registration mode.
2. Press a button on the keypad making sure that one of the Battery LEDs lights up when the button is pressed.
3. Wait for five seconds and press the same button again.
Wall Mounting
After registration, test the EL-2620 from the required
mounting location before permanently mounting to the wall.
To mount the EL-2620 to the wall:
1. Remove the back cover by inserting a small
screwdriver into the pry-off slots at the bottom of the
unit and twisting.
2. Secure the back cover to the wall using four screws.
Battery Replacement
Every time a key is pressed, one of the battery status
LEDs is lit. When the battery needs to be replaced, the
red Low Battery LED is lit.
To replace the battery:
1. Remove the back cover as explained above.
2. Observing correct polarity, replace the battery (9V alkaline).
3. Replace the back cover making sure that the two covers click shut.
Technical Specifications
Antenna: Built-in whip
Frequency: 418MHz FM
Current Consumption: 26mA (transmission), 2µA (standby)
Power: 9V Alkaline Battery (Eveready 522)
RFI Immunity: 40V/m
Operating Temperature: 32-140°F (0 to 60°C)
Dimensions: 4.3”H X 5.1”W X 1.1”D (130 x 110 x 28mm)
FCC ID: RIYEL2620
Figure 1: EL-2620 (front view)
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequenc
y
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna, 2. Increase the separation between the equipment and the receiver, 3. Connect the equipment into an outlet on a
circuit different from that to which the receiver is connected, 4. Consult the dealer or an experienced radio/TV technician for help.
Warning: Changes or modifications to this equipment not expressly approved by the party responsible for compliance (Electronics Line 3000 Ltd.) could void the
user’s authority to operate the equipment.
Electronics Line 3000 Ltd.: 2 Granit Street, Kiryat Arieh, POB 3253, Petah Tikvah 49130 Israel. Tel: [phone], Fax: [phone]
USA: 5637 Arapahoe Avenue, Boulder, Colorado 80303. Tel: [phone], Fax: [phone]
UK: Unit 7, Leviss Trading Estate, Station Road, Stechford, Birmingham B33 9AE. Tel: [phone], Fax: [phone]
France: ZI-61, rue du Marché Rollay, 94500 Champigny-Sur-Marne. Tel: [phone], Fax: [phone]
ZI0312A (11/03)
A
ll data is subject to change without prior notice. In no event shall Electronics Line 3000 Ltd. (EL3K) be liable for an amount in excess of EL3K.’s original selling price o
f
this product, for any loss or damage whether direct, indirect, incidental, consequential or otherwise arising out of any failure of the product.
Figure 2: EL-2620 (back cover off)
Tampe
r
Switch
Batter
y
Transmitte
r
Buzze
r