User's Manual

ManualsBrandsElectronic Systems Technology ManualsElectronicsESTEEM 195Eg

CHAPTER 5

EXAMPLE CONFIGURATIONS

Revised: 23 Jan 08 5-18 EST P/N AA107G

Example 3 – Remote Building (Access Point Bridge with Repeater Enabled)

1. Review Example #1 diagram (Figure 1) and locate the 195Eg marked as Example 3. This ESTeem is connected to a Remote

Building network that will be bridged to the Plant network through the Access Point Router (Example #1) via the repeater. This

modem should be configured for Access Point Bridge mode and the configuration for this 195Eg will be identical to Example 2

except that the IP addressing and the Repeater Peer table. You would follow all steps 1-11 in Example 2 to configure this

195Eg also but Figures 31 & 32 will show the changes.

Figure 31: Example 3 Bridge IP Address

Figure 32: Example 3 Repeater Routing Table

Summary of content (10 pages)

PAGE 1
CHAPTER 5 EXAMPLE CONFIGURATIONS Example 3 – Remote Building (Access Point Bridge with Repeater Enabled) 1. Review Example #1 diagram (Figure 1) and locate the 195Eg marked as Example 3. This ESTeem is connected to a Remote Building network that will be bridged to the Plant network through the Access Point Router (Example #1) via the repeater.
PAGE 2
CHAPTER 5 EXAMPLE CONFIGURATIONS Example 4 – Mobile Vehicle with Single Ethernet Device (EtherStation Mode) Review the Example Diagram #1 (Figure 1) and locate the 195Eg marked as Example 4. This ESTeem is connected to a single Ethernet device in a mobile application and will be configured for EtherStation mode.
PAGE 3
CHAPTER 5 EXAMPLE CONFIGURATIONS 3. Enter the WEP key values for your application that will be used by all devices on the wireless network. Reference Figure 35. Figure 35: WEP Key Input 4. Select Commit Changes to write the programming to Flash memory and reboot the Model 195Eg. When the reboot process has completed (approximately 30 seconds) the modem will be ready to place in operation. Reference Figure 36.
PAGE 4
CHAPTER 5 EXAMPLE CONFIGURATIONS Example 5 – Mobile Vehicle #1 (Station Router) Review the Example Diagram #2 (Figure 2) and locate the 195Eg marked as Example 5. This ESTeem is connected to multiple Ethernet devices in a mobile application and will be configured Station Router mode. In this mode the 195Eg’s will gain access to the wireless Ethernet canopy created by the Access Point and act as the router between the devices connected to the Ethernet port and wireless network.
PAGE 5
CHAPTER 5 EXAMPLE CONFIGURATIONS 1. Access the ESTeem Web page using your computer’s Web Browser as per instructions in Chapter 4. Select Setup from the menu items. From the Select Mode of Operation pull down box , select Station Router (Figure 38) and push the Next button below the pull down box. Figure 38:Station Router Selection 2. Select Yes if you would like to use DHCP services on either the wireless or ethernet connections. Enter the SSID for you 802.11g network.
PAGE 6
CHAPTER 5 EXAMPLE CONFIGURATIONS 3. Enter the WEP key values for your application that will be used by all devices on the wireless network. Reference Figure 40. Figure 40:WEP Key Input 4. Refer to the IP address in Table 1 and enter the wireless IP Address and IP Netmask for the Station Router. Reference Figure 41.
PAGE 7
CHAPTER 5 EXAMPLE CONFIGURATIONS 5. Refer to the IP address in Table 1 and enter the ethernet IP address and IP netmask. Reference Figure 42. Note: When configuring the Ethernet devices connected to the Station Router 195Eg, the ethernet IP address will be their Gateway address (Figure 37). Figure 42:Wired Ethernet IP Address 6. All IP requests for the Ethernet devices connected to the 195Eg Station Router (Example #5) will need to be resolved by the Network Router (Figure 37).
PAGE 8
CHAPTER 5 EXAMPLE CONFIGURATIONS Example 6 – Mobile Vehicle #2 (Station Masquerade) Review the Example Diagram #2 (Figure 2) and locate the 195Eg marked as Example 6. This ESTeem is connected to multiple Ethernet devices in a mobile application and will be configured Station Masquerade mode. In this mode the 195Eg’s will gain access to the wireless Ethernet canopy created by the Access Point and act as a firewall between the devices connected to the Ethernet port and wireless network.
PAGE 9
CHAPTER 5 EXAMPLE CONFIGURATIONS 2. Select Yes if you would like to use DHCP services on either the wireless or ethernet connections. Enter the SSID for you 802.11g network. The SSID is the unique identification for your wireless network and all 802.11g devices that share a wireless network MUST have the same SSID code. This identification code is case sensitive and must NOT contain spaces. Select the encryption level for the wireless network to match the level of the Access Point canopy.
PAGE 10
CHAPTER 5 EXAMPLE CONFIGURATIONS 5. Refer to the IP address in Table 1 and enter the ethernet IP address and IP netmask. Reference Figure 48. Note: When configuring the Ethernet devices connected to the Station Router 195Eg, the ethernet IP address will be their Gateway address (Figure 37). Figure 48:Wired Ethernet Interface 6. All IP requests for the Ethernet devices connected to the 195Eg Station Router (Example #5) will need to be resolved by the Network Router (Figure 37).