ELECTRIC HOB FEH 610 35685-3501 INSTRUCTION BOOKLET GB
Important Safety Information You MUST read these warnings carefully before installing or using the hob. If you need assistance, contact our Customer Care Department on 08705 950950 Installation z z z z This hob must be installed by qualified personnel, according to the manufacturer’s instructions and to the relevant British Standards. Remove all packaging before using the hob. Ensure that the electrical supply complies with the type stated on the rating plate, located on the bottom of the hob.
Contents For the User For the Installer Important Safety Information 2 Installation 9 Description of the Hob 3 Building In 9 Operation 4 Electrical connections 10 Maintenance and Cleaning 5 Wiring diagram 11 Something Not Working? 6 Service and Spare Parts 6 Guarantee Conditions 7 Description of the Hob 3 4 2 1 6 5 7 1. Hob Top 2. Normal Hotplate - 1570 W - 180 mm dia. 3. Normal Hotplate - 1040 W - 145 mm dia. 4. Rapid Hotplate - 2090 W - 180 mm dia. 5.
Operation Electric Hotplates To switch on a hotplate, turn the relevant control knob anticlockwise to the required heat setting. The control knob is numbered 1 - 6 0 - OFF 1 - Minimum 6 - Maximum. The hob has two types of hotplates: Normal Hotplates We recommend the plates are switched to maximum (6) for a short while to boost the plate, and then adjusted to the required setting. Rapid Hotplates The rapid hotplates are indicated by a red dot, and will heat up more quickly than a normal plate.
Take care never to lean or reach over a hot electric plate. Always point pan handles inward or over the work surface next to the hob to avoid accidentally knocking over a pan as you pass by. Take care when frying food in hot oil or fat, as the overheated splashes could easily ignite. If the control knobs become difficult to turn, please contact your local Service Force Centre.
Something Not Working? If the hob is not working correctly, please carry out the following checks before contacting your local Service Force Centre. IMPORTANT: If you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or installation, a charge will be made even if the appliance is under guarantee. SYMPTOM SOLUTION The plate does not heat up.
Guarantee Conditions Standard guarantee conditions European Guarantee We, EHP, undertake that if, within 12 months of the date of the purchase, this Firenzi appliance or any part thereof is proved to be defective by any reason only of faulty workmanship or materials, we will, at our option, repair or replace the same FREE OF ANY CHARGE for labour, materials or carriage on condition that: * The appliance has been correctly installed and used only on the gas and electricity supply stated on the rating plate
Instructions for the Installer Engineers technical data Overall dimensions Heating elements Ratings Normal front left Hotplate Normal back left Hotplate Rapid front right Hotplate Rapid back right Hotplate Total rating Ø 180 mm Ø 145 mm Ø 145 mm Ø 180 mm 1570 W 1040 W 1570 W 2090 W 6270 W Width: Depth: 580 mm. 500 mm. Cut out dimensions Width: Depth: 550 mm. 470 mm.
Installation The hob must be installed according to the instructions supplied. The hob must be installed by qualified personnel to the relevant British Standards. Please, ensure that, once the hob is installed, it is easily accessible for the engineer in the event of a breakdown. Cut Out Size When the hob is first installed Once the hob has been installed, it is important to remove any protective materials, which were put on in the factory.
Building over a kitchen unit with door 20 min Proper arrangements must be taken in designing the furniture unit, in order to avoid any contact with the bottom of the hob which can be hot when in operation. The recommended solution is shown in diagram 3. The panel fitted under the hob ("a") should be easily removable to allow easy access if technical assistance is needed. The space behind the kitchen unit ("b") can be used for connections. 30 3 a 60 b FO 1013 Dimensions are given in mm.
The hob is supplied without a supply cable. A 3 core flexible supply cable must be fitted, in accordance with the specification given in the relevant tables. ) 1) Remove the mains terminal cover plate from the underside of the hob, to expose the mains terminal block. 2) Loosen the two cable clamp screws and lift the top section of the clamp enough to allow the cable to be passed through. 3) Connect the red (live) wire to the terminal which is marked with the letter "L".
35685-3501 09/03 Grafiche MDM - Forlì