I N F O I S T R U Z I O N I P E R L ’ I N S TA L L A Z I O N E E L ’ U S O I N S TA L L AT I O N A N D I N S T R U C T I O N M A N U A L CONGELATORE FREEZER EU 1830 I I t 2222739-43
Contents Important Safety Instructions 13 Instructions for the installer Instructions for the user Use 15 Cleaning the interior Operation Control panel Starting-up and temperature regulation NORMAL-SUPER switch Warning light Quick freezing Freezing of fresh foods and storage of commercially frozen food Ice-cube trays Thawing Defrosting 15 15 15 15 15 15 16 Maintenance 18 Periodic clearing Periods of non-operation 18 18 Customer service and spare parts 18 18 16 16 17 12 Technical specification
Important Safety Instructions t It is most important that this instruction book should be retained with the appliance for future reference. Should the appliance be sold or transferred to another owner, or should you move house and leave the appliance, always ensure that the book is supplied with the appliance in order that the new owner can be acquainted with the functioning of the appliance and the relevant warnings. These warnings are provided in the interest of safety.
■ ■ ■ ■ ventilation must be as shown in the relevant Figure. Attention: keep ventilation openings clear of obstruction. If the appliance is transported horizontally, it is possible that the oil contained in the compressor flows in the refrigerant circuit. It is advisable to wait at least two hours before connecting the appliance to allow the oil to flow back in the compressor. There are working parts in this product which heat up.
t Use The freezer is marked with the symbol, which means that the compartment is suitable for freezing fresie food and long-term storage of frozen food. Cleaning the interior Before using the appliance for the first time, wash the interior and all internal accessories with lukewarm water and some neutral soap so as to remove the typical smell of a brand-new product, then dry thoroughly. Do not use detergents or abrasive powders, as these will damage the finish.
Quick freezing Storage of commerclally frozen food Slide switch (F) towards the right to position «S» («SUPER»). Indicator light (E) will then light up.
t Defrosting Frost should be removed from the inside of the compartment with the special plastic scraper provided, whenever the thickness exceeds 4 mm. Do not use metal tools to remove frost so as to avoid seriously damaging the appliance. If a thick layer of ice is formed it will be necessary to carry out complete defrosting as following: 1. unplug the appliance from the mains socket or set knob (B) to position «O». 2.
Maintenance Unplug the appliance before carrying out any maintenance operation. Periods of non-operation During periods when the appliance is not used, you should take the following precautions: remove the plug from the wall socket; remove all food from the appliance; defrost and clean the interior and all accessories; leave the door slightly open, thus letting air circuiate and preventing the formation of mould and unpleasant smells.
t Technical specifications The technical data is indicated in the rating plate on the left side inside the appliance. Installation lf this appliance featuring magnetic door seals is to replace an older appliance having a spring lock (latch) on the door or lid, be sure to make that spring lock unusable before you discard the old appliance. This will prevent it from becoming a death-trap for a child.
For safety reasons, minimum ventilation must be as shown in Fig. Attention: keep ventilation openings clear of obstruction. 50 540 560 m 550 in H 50 min H1 If a refrigerator is fitted into a tall kitchen unit together with the freezer, air intake must be both through the grille fixed to the appliance and through a grille fixed to an opening made in the kitchen unit base, having the minimum dimensions indicated in the diagram. 50 H H1 50 54 Air entry min 200 cm 2 20 0 D464 1.
t 2. Push the appliance up against the side opposite the door hinge. Fix the appliance with the 4 screws supplied. Fit the hinge cover (D), clipping it into place. D D648 3. Press on the seal between the appliance and the kitchen unit. D466 4. Apply covers (B) on joint cover lugs and into hinge holes.
5. Position the runners (H) at the top and bottom of the inside of the kitchen unit as shown in the figure and mark the position of the external holes. After preparing the holes, screw the runners to the kitchen unit door using 3.5x16 mm screws. H 20m m D094 6. Open both the appliance door and that of the kitchen unit to approx. 90°. Place the little platee over the runners. Hold the doors of the appliance and the unit together and mark the holes. 8mm PR34 7.