用户手册 user manual 冰箱 Fridge-Freezer ERN29800
electrolux Electrolux. Thinking of you. 在 www.electrolux.
electrolux 3 • 建议等待至少四个小时后再连接冰箱,以 便油流回到压缩机中。 • 冰箱周围应该留有足够空间供空气流动, 否则,会导致冰箱过热。 为充分通风,请 按照相关说明进行安装。 • 尽可能将冰箱背靠墙放立,以免碰触到发 热的部件(压缩机、冷凝器),以防灼 伤。 • 不得将冰箱放置到靠近取暖器或炉灶的地 方。 • 安装冰箱后,确保可以够得到插头。 • 仅限于连接到饮用水源。 4) • 不要在本冰箱内存放可燃气体或液体,因 为它们可能会爆炸。 • 不要将食品放在后壁的出风口处。 3) • 冷冻食品一旦解冻后,就不宜再次冷冻。 • 存放包装好的冷冻食品时请遵守冷冻食品 制造商的说明。 • 必须严格遵守冰箱制造商的存放建议。 具 体请参阅相关说明。 • 不要将碳酸饮料放入冷冻室内,因为这可 能导致饮料容器内产生压力,引起爆炸, 损坏本冰箱。 • 如果从冰箱直接取出冰棒就吃,可能导致 冻灼。 维修 • 维修电气所需的任何电气工作都应该由具 备资格的电气工程师或有相当能力的人员 进行。 • 本产品必须由授权的维修中心进行维修, 并且只能使用原装零配件。 保养和清洁 • 进行维护之前,请关闭冰箱电
electrolux 显示屏 1 2 1 2 3 4 5 6 7 8 3 冷藏室指示器 冷冻室指示器 正或负温度指示器 温度指示器 Action Freeze功能 Shopping功能 Minidac功能 Performance Optimization功能 开机 将插头插入电源插座之后,如果显示屏不 亮,按开关按钮。 在冰箱启动之后,控制面板上会出现以下信 号: • 正或负温度指示器将为正,表明温度为零 上。 • 温度值会闪烁,显示屏的背景为红色,并 且您会听到蜂鸣器在发出声音。 按下功能按钮,蜂鸣器将会关闭(另请参阅 “温度过高警报”)。 设定所需的温度(请参阅“温度调节”)。 关机 按住开关一秒以上,冰箱将会关机。 在此之后,将会显示温度倒数 -3 -2 -1。 在冰箱关机后,显示屏也将关闭。 温度指示 每次按下冰箱温度指示按钮,显示屏会按顺 序指示: 1. – 冷藏室指示灯亮起。 – 显示屏显示冷藏温度。 2.
electrolux 5 通过按功能按钮可以随时禁用该功能(请参 阅“功能启动”)。 Shopping功能 如果需要放入大量温度较高的食物,例如从 商场买回大量食物之后,我们建议启动 Shopping功能以便更快地使其冷却,从而避 免使已经存放在冰箱中的其他食物温度升 高。 要启动Shopping功能,请按功能按钮(如果 需要,请按数次)直至出现相应的图标 。 Shopping功能会在大约 6 小时后自动关闭。 在Shopping功能启动期间,冷藏室内部的风 扇也会自动启动。 重要事项! 当室内温度很高时(超过 38°C),即使Shopping功能未被启动,冷 藏室内部的风扇也会自动启动。 通过按功能按钮可以随时禁用该功能(请参 阅“功能菜单”)。 Action Freeze功能 要冷冻新鲜食物,需要启动Action Freeze功 能。按功能按钮(如果需要,请按数次)直 至出现相应的图标。 该功能会在 52 小时后自动停止。 通过按功能按钮可以随时禁用该功能(请参 阅“功能菜单”)。 温度过高警报 当冷冻室内的温度升高时(例如由于断 电),将会通过以下方式指示: • 温度闪烁 • 冷冻室闪烁(冷冻室指示
electrolux 小块食品甚至可以从冷冻室取出后直接进行 烹煮,无需解冻: 在这种情况下,可能需要 烹煮较长时间。 冰块制作 本冰箱配备了一个或多个用于制作冰块的盘 子。 在盘子中倒入水,然后放入冷冻室。 重要事项! 请勿使用金属器具取出冷冻室中 的冰块盘。 可移动搁架 冷藏室壁上有一些滑槽,可根据需要安放搁 架。 为了更好地利用空间,前半个搁架可以搭在 后半个上。 湿度控制 玻璃搁架包含一个带有缝隙的装置(可通过 滑杆进行调节),使得能够调节蔬菜抽屉的 温度。 当通风槽关闭时: 水果和蔬菜隔层中食物的天然含水量可保持 较长时间。 当通风槽打开时: 更多的空气流通会使水果和蔬菜隔层中具有 较低的空气水分含量。 安放门搁架 为了能够存放不同包装大小的食品,门搁架 高低可调。 请按以下步骤进行调整: 沿箭头所示方向缓缓拉出搁架,直到其完全 拉出,然后根据需要重新安放。 空气循环 冷藏室配有一个特殊的 D.A.C.
electrolux 7 当室内温度高于 38°C 或者当Shopping功能 打开时,风扇自动设置为打开。 可以随时将风扇设置为关闭,只需按功能按 钮直至图标 消失。 A 实用建议和提示 节能提示 • 不要经常打开冰箱门,若非绝对必要,也 不要打开过长时间。 • 如果在环境温度较高,且温度调节器设定 在较低的温度,而冰箱又装满了食品,那 么压缩机有可能会不停地运转而导致蒸发 器结霜或结冰。 如果发生这种情况,请将 温度调节器转向较高设置,以便进行自动 除霜和节省耗电量。 新鲜食品冷藏提示 如欲获得最佳性能: • 不要在冷藏室存放热食或挥发性液体 • 如果食品味道浓烈,请一定要盖上盖子或 包裹好 • 摆放好食物,使其周围空气可以自由流通 冷藏提示 实用提示: 肉(所有肉类): 装到保鲜袋中并放到蔬菜 抽屉上的玻璃搁架上。 安全起见,这种方式存放的食品最多只能保 存一、两天。 熟食、凉菜等等: 这些食物应该盖上盖,可 以放在任何搁架上。 水果和蔬菜: 这些食品应该彻底清洗并放在 随附的特定抽屉内。 黄油和奶酪: 这些食品应该放在特制的密封 容器内或裹在铝箔或塑料保鲜袋中,以最大 限度地排除空气。 奶瓶:
electrolux • 一旦解冻,食品很快就会变质,不宜再冷 冻。 • 不要超过食品生产商标示的存放时间。 养护和清洁 小心! 执行任何维护操作之前,先拔下 冰箱插头。 本冰箱的冷却装置中含有碳氢化合物; 因此,维护和充注工作必须由授权的技 术人员进行。 定期清洁 本设备必须要定期清洁: • 使用微温的水和中性肥皂清洁内部及附 件。 • 定期检查门密封条并擦抹清洁,确保其干 净无屑。 • 清洗并彻底干燥。 重要事项! 不要拉扯、移动或损坏机体内部 的管道和/线缆。 不得使用去污剂、磨砂粉、浓香型清洁产品 或抛光蜡产品清洁内部,因为这会损坏表面 并留下强烈气味。 使用刷子或真空清洁器清洁冷凝器(黑色铁 架)和冰箱背后的压缩机。 这会提高冰箱性 能并节省耗电量。 重要事项! 小心操作,不要损坏冷却系统。 很多厨房专用的表面清洁剂都含有可能浸 蚀/损害本冰箱塑料的化学成分。 因此,建 议在清洁本冰箱的外壳表面时,使用只加了 少许清洁剂的温水。 清洁之后,重新将冰箱连接至电源。 冷藏室除霜 正常使用期间,每当压缩机电机停止运转 时,冷藏室蒸发器上的霜会自动消除。 霜融 化成的水会顺着水槽流到冰箱背部压缩机
electrolux 9 6. 两到三个小时后,将之前取出的食品重 新装入冰箱。 警告! 严禁使用尖锐的金属工具铲除蒸 发器上面的霜冻,因为这样有可能会损 坏蒸发器。 不得使用机械设备或制造商建议之外的 任何人工方法加快溶化速度。 在除霜过程中,冷冻的食品包装温度如 升高,则食品的储存保质期可能缩短。 4. 除霜完成时,彻底干燥内部并收好塑料 铲以备将来使用。 5.
electrolux 故障 冰箱内的温度过高。 可能的原因 解决办法 温度调节器设定不当。 设定一个较低的温度。 未正确关闭冰箱门。 参阅“关闭冰箱门”。 食品温度过高。 等待食品的温度降至室温之后再进 行储存。 一次性储存食品过多。 减少一次性储存食品的数量。 冰箱内的温度过高。 冰箱内部没有冷气流通。 确保冰箱内部有冷气流通。 冷冻室内的温度过高。 食品与食品之间的间隙太小。 储存食品的方式应当确保冷气流通 不受阻碍。 霜冻过多。 食品包裹不当。 正确包裹食品。 未正确关闭冰箱门。 参阅“关闭冰箱门”。 更换灯泡 如果要更换灯泡,请按下述步骤操作: 1. 断开冰箱电源。 2. 按下后方挂钩并同时沿箭头方向滑动外 盖。 3. 更换为功率相同且专用于家用电器的灯 泡(灯泡外盖上标有最大功率)。 4. 滑动灯盖,使其恢复原位。 5. 重新接通冰箱电源。 6. 打开冰箱门,检查灯是否亮起。 关闭冰箱门 1. 清洁冰箱门垫圈。 2. 如果需要,请调整冰箱门。 请参阅"安 装"。 3.
electrolux 11 安装 安装冰箱之前请仔细阅读"安全信息", 以确保您的安全以及冰箱的正常工作。 安放位置 安装冰箱的地方的环境温度应该与冰箱定额 牌上所示的气候类型相对应: 气候类型 C 环境温度 (亚温 带) +10°C 到 +32°C (温带) +16°C 到 +32°C (亚热 带) +16°C 到 +38°C (热带) +16°C 到 +43°C 电气连接 插入之前,请确保定额牌上所示的电压和频 率与您的家庭电源相对应。 本冰箱必须接地。 随附的电源插头提供了用 于接地的插脚。 如果家庭电源未接地,请咨 询具备资格的电工,根据现行法规将冰箱单 独接地。 如果没有遵循上述安全预防措施,制造商概 不承担任何责任。 本冰箱符合欧盟法令 (EEC 法令)的规定。 门可两边开 冰箱的门为右开。如果您想换为左开,请在 安放冰箱之前执行以下步骤: 1. 松开上销钉并取下定位片。 2. 取下上销钉并卸下上面的门。 3. 取下铰链盖 (A)。卸下销钉 (B) 和定位 片 (C)。装上铰链盖 (A)。 4. 卸下下面的门。 5. 松开下方的销钉。 B A 在对边上: 1.
electrolux min. 200 cm2 4mm min. 200 cm2 安装冰箱 小心! 确保主电线可以自由地移动。 请执行以下步骤。 1. 将冰箱安装到橱柜中。 沿箭头(1)所示的方向推动冰箱,直至间 隙盖顶到厨柜。确保冰箱和橱柜前边之 间的距离为44毫米。 沿箭头(2)所示方向把冰箱推靠在铰链对 边的橱柜上。确保冰箱和橱柜之间有4毫 米的距离。 2 44mm 3. 使用4颗螺钉将冰箱固定到橱柜上。 I 4. 压入冰箱和相邻机壳之间的密封条。 1 2. 调整冰箱在橱柜中的位置。 下铰链盖(在附件包中)可确保冰箱和厨 柜之间的距离准确。 打开冰箱门。将下铰链盖安放到位。 5.
electrolux 13 6. 将护盖(C,D)安装到凸片和铰链孔上。 安装通风栅格(B)。 将铰链盖(E)安装到铰链上。 D 8. 分开部件Ha、Hb、Hc和Hd Ha C Hb E E Hc B 7. 如果冰箱必须连接到橱柜门的侧面: a) 请松开固定托座 (H) 的螺钉。 b) 移开托座 (H)。 c) 重新拧紧螺钉。 Hd 9. 将部件Ha安装到橱柜内壁上。 ca. 50 mm 90° 21 mm 90° ca. 50 mm 21 mm 10.
electrolux 13. 重新将小方块放到导轨上,然后用随附 的螺钉将其固定。 通过调整部件Hb,对齐橱柜门和冰箱 门。 Ha Hc 11. 将冰箱门和橱柜门打开到90°位置。 将小方块(Hb)插入到导轨(Ha)内。 将冰箱门和橱柜门合在一起并记下孔 眼。 Hb 14. 将部件Hd压到部件Hb上。 8 mm Hb Ha Hb 12.
electrolux 15 环境注意事项 产品上或其包装上的 标记表示不能把本 产品作为家庭垃圾般处理,而是应该将其送 至适当的电气和电子设备回收站点。通过确 保本品得到正确处理,您可以帮助避免由于 本产品废弃后处理不当而给环境和人类健康 带来的潜在负面效果。如需了解更多有关本 产品回收的详细信息,请联系您当地的废品 回收部门、您的家庭垃圾处理服务点或您购 买本产品的商店。
electrolux Electrolux. Thinking of you. Share more of our thinking at www.electrolux.
electrolux 17 damage to the cord may cause a shortcircuit, fire and/or electric shock. Warning! Any electrical component (power cord, plug, compressor) must be replaced by a certified service agent or qualified service personnel. • • • • 1. Power cord must not be lengthened. 2. Make sure that the power plug is not squashed or damaged by the back of the appliance. A squashed or damaged power plug may overheat and cause a fire. 3. Make sure that you can come to the mains plug of the appliance. 4.
electrolux in either its refrigerant circuit or insulation materials. The appliance shall not be discarded together with the urban refuse and rubbish. The insulation foam contains flammable gases: the appliance shall be disposed according to the applicable regulations to obtain from your local authorities. Avoid damaging the cooling unit, especially at the rear near the heat exchanger. The materials used on this appliance marked by the symbol are recyclable.
electrolux 19 Switching off The appliance is shut off by pressing ON/ OFF switch for more than 1 second. After this, a countdown of the temperature from -3 -2 -1 will be shown. When the appliance is switched off, Display also goes off. Temperature Indication Each time the Fridge-Freezer temperature indication button is pressed, the display indicates in sequence: 1. – The Fridge compartment indicator is on. – The display indicates the fridge temperature. 2. – The Freezer compartment indicator is on.
electrolux sary) until the corresponding icon appears . The Shopping function shuts off automatically after approximately 6 hours. During the Shopping function also the fan inside the refrigerator compartment is automatically activated. Important! The fan inside the refrigerator compartment is automatically activated also when the room temperature is high (over 38°C), even though the Shopping function is not activated.
electrolux 21 compartment let the appliance run at least 12 hours on the Action Freeze setting. If large quantities of food are to be stored, remove all drawers and baskets from appliance and place food on cooling shelves to obtain the best performance.
electrolux more air circulation results in a lower air moisture content in the fruit and vegetable compartments. When the green light (A) comes on, the fan is working. When the ambient temperature exceeds 25°C, set the fan to ON. When the room temperature is higher than 38°C or when the Shopping function is ON, the fan is automatically ON. It is possible to set the fan OFF at any time by pressing the Function button until the icon goes out of view.
electrolux 23 Hints for freezing To help you make the most of the freezing process, here are some important hints: • the maximum quantity of food which can be frozen in 24 hrs. is shown on the rating plate; • the freezing process takes 24 hours.
electrolux the water overflowing and dripping onto the food inside. Use the special cleaner provided, which you will find already inserted into the drain hole. Defrosting the freezer A certain amount of frost will always form on the freezer shelves and around the top compartment. Defrost the freezer when the frost layer reaches a thickness of about 3-5 mm.
electrolux 25 WHAT TO DO IF… Warning! Before troubleshooting, disconnect the mains plug from the mains socket. Only a qualified electrician or competent person must do the troubleshooting that is not in this manual. Problem Important! There are some sounds during normal use (compressor, refrigerant circulation). Possible cause Solution The appliance is switched off. Switch on the appliance. The mains plug is not connected to the mains socket correctly.
electrolux Problem Possible cause Solution Many products are stored at the same time. Store less products at the same time. The temperature in the refrigerator is too high. There is no cold air circulation in the appliance. Make sure that there is cold air circulation in the appliance. The temperature in the freezer is too high. Products are too near to each other. Store products so that there is cold air circulation. There is too much frost. Food is not wrapped correctly.
electrolux 27 Positioning Install this appliance at a location where the ambient temperature corresponds to the climate class indicated on the rating plate of the appliance: Climate class Ambient temperature SN +10°C to + 32°C N +16°C to + 32°C ST +16°C to + 38°C T +16°C to + 43°C Electrical connection Before plugging in, ensure that the voltage and frequency shown on the rating plate correspond to your domestic power supply. The appliance must be earthed.
electrolux 2 1 Ventilation requirements The airflow behind the appliance must be sufficient. min. 200 cm2 2. Adjust the appliance in the niche. The lower hinge cover (in the accessories bag) makes sure that the distance between the appliance and the kitchen furniture is correct. Open the door. Put the lower hinge cover in position. min. 200 cm2 4mm Installing the appliance 44mm Caution! Make sure that the mains cable can move freely. Do these steps. 1. Install the appliance in the niche.
electrolux 29 Install the vent grille (B). Attach the hinge covers (E) to the hinge. I D C E 4. Push the sealing strip between the appliance and the adjacent cabinet. E B 7. If the appliance must connect laterally to the kitchen furniture door: a) Slacken the screws in fixing brackets (H). b) Move the brackets (H). c) Retighten the screws. 5. Remove the correct part from the hinge cover (E). Make sure to remove the part DX, in the case of right hinge, SX in opposite case. 8.
electrolux Put together the appliance door and the furniture door and mark the holes. Ha Hb 8 mm Hc Hd 9. Install the part Ha on the inner side of the kitchen furniture. Ha Hb 12. Remove the brackets and mark a distance of 8 mm from the outer edge of the door where the nail must be fitted (K). ca. 50 mm 90° 8 mm 21 mm 90° ca. 50 mm 21 mm 10. Push the part Hc on the part Ha. Ha Hc 11. Open the appliance door and the kitchen furniture door at an angle of 90°.
electrolux 31 Hb Hb 14. Press the part Hd on the part Hb. Hd Do a final check to make sure that: • All screws are tightened. • The magnetic sealing strip is attached tightly to the cabinet. ENVIRONMENTAL CONCERNS The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it should be taken to the appropriate collection point for the recycling of electrical and electronic equipment.
www.electrolux.