user manual notice d'utilisation benutzerinformation istruzioni per l’uso Fridge Réfrigérateur Kühlschrank Frigorifero ERC34393W
electrolux Electrolux. Thinking of you. Share more of our thinking at www.electrolux.
electrolux 3 damage to the cord may cause a shortcircuit, fire and/or electric shock. Warning! Any electrical component (power cord, plug, compressor) must be replaced by a certified service agent or qualified service personnel. • • • • 1. Power cord must not be lengthened. 2. Make sure that the power plug is not squashed or damaged by the back of the appliance. A squashed or damaged power plug may overheat and cause a fire. 3. Make sure that you can come to the mains plug of the appliance. 4.
electrolux in either its refrigerant circuit or insulation materials. The appliance shall not be discarded together with the urban refuse and rubbish. The insulation foam contains flammable gases: the appliance shall be disposed according to the applicable regulations to obtain from your local authorities. Avoid damaging the cooling unit, especially at the rear near the heat exchanger. The materials used on this appliance marked by the symbol are recyclable.
electrolux 5 DAILY USE Movable shelves The walls of the refrigerator are equipped with a series of runners so that the shelves can be positioned as desired. To make these adjustments proceed as follows: gradually pull the shelf in the direction of the arrows until it comes free, then reposition as required. Positioning the door shelves To permit storage of food packages of various sizes, the door shelves can be placed at different heights.
electrolux CARE AND CLEANING Caution! Unplug the appliance before carrying out any maintenance operation. This appliance contains hydrocarbons in its cooling unit; maintenance and recharging must therefore only be carried out by authorized technicians. Periodic cleaning The equipment has to be cleaned regularly: • clean the inside and accessories with lukewarm water and some neutral soap. • regularly check the door seals and wipe clean to ensure they are clean and free from debris.
electrolux 7 Important! There are some sounds during normal use (compressor, refrigerant circulation). Problem Possible cause Solution The appliance is switched off. Switch on the appliance. The mains plug is not connected to the mains socket correctly. Connect the mains plug to the mains socket correctly. The appliance has no power. There is no voltage in the mains socket. Connect a different electrical appliance to the mains socket. Contact a qualified electrician. The lamp is in stand-by.
electrolux Replacing the bulb If you want to replace the bulb, do these steps: 1. Break the circuit of the appliance. 2. Press on the rear hook and at the same time slide the cover in the direction of the arrow. 3. Replace the bulb with one of the same power and specifically designed for household appliances. the maximum power is shown on the light bulb cover) 4. Replace the light cover by sliding it into its original position. 5. Reconnect the appliance. 6. Open the door and check if the light comes on.
10mm 10mm 100mm electrolux 9 Electrical connection Before plugging in, ensure that the voltage and frequency shown on the rating plate correspond to your domestic power supply. The appliance must be earthed. The power supply cable plug is provided with a contact for this purpose. If the domestic power supply socket is not earthed, connect the appliance to a separate earth in compliance with current regulations, consulting a qualified electrician.
electrolux e d 2 1 f d 4 • Remove the screw of the hinge cover plug (a) . • Unscrew the upper hinge and remove it (b). • Unscrew the screw and remove the door stopper (c). 5 3 • Lift up the appliance to vertical position. • Open the door and reposition the upper door plastic trim with screws. b c a • Fix the handle on the opposite side, insert the plastic plugs into the holes left open that can be found in the instruction for use bag. • Remove the door.
electrolux 11 Warning! After having reversed the opening direction of the doors check that all the screws are properly tightened and that the magnetic seal adheres to the cabinet. If the ambient temperature is cold (i.e. in Winter), the gasket may not fit perfectly to the cabinet. In that case, wait for the natural fitting of the gasket. Lay down the appliance back side down.
electrolux Electrolux. Thinking of you. Partagez notre imagination sur www.electrolux.
electrolux 13 naturel offrant un haut niveau de compatibilité avec l’environnement mais qui est néanmoins inflammable. Pendant le transport et l'installation de l’appareil, assurez-vous qu'aucune pièce du circuit de refroidissement n'est endommagée. Si tel est le cas : – Évitez les flammes vives (briquet) et tout autre allumage (étincelles). – Aérez soigneusement la pièce où se trouve l'appareil. • Ne modifiez pas les spécifications de l'appareil.
electrolux • Branchez à l'alimentation en eau potable uniquement. 9) soin. Si l'orifice est bouché, l'eau s'écoulera en bas de l'appareil. Installation Maintenance • Les branchements électriques nécessaires à l'entretien de l'appareil doivent être réalisés par un électricien qualifié ou une personne compétente. • Cet appareil ne doit être entretenu et réparé que par un Service après-vente autorisé, exclusivement avec des pièces d'origine.
electrolux 15 Toutefois, le réglage doit être choisi en tenant compte du fait que la température à l'intérieur de l'appareil dépend de plusieurs facteurs : • la température ambiante • la fréquence d'ouverture de la porte • la quantité de denrées stockées • l'emplacement de l'appareil. Important Si le thermostat est réglé sur la position de froid maximum, lorsque la température ambiante est élevée ou que l'appareil est plein, il est possible que le compresseur fonctionne en régime continu.
electrolux CONSEILS UTILES Conseils pour l'économie d'énergie • N'ouvrez pas la porte trop souvent ou plus longtemps que nécessaire. • Si la température ambiante est élevée, le dispositif de réglage de température est sur la position de froid maximum et l'appareil est plein : il est possible que le compresseur fonctionne en régime continu, d'où un risque de formation excessive de givre sur l'évaporateur.
electrolux 17 d'utilisation normale. L'eau de dégivrage est collectée dans un récipient spécial situé à l'arrière de l'appareil, au-dessus du compresseur, d'où elle s'évapore. Il est important de nettoyer régulièrement l'orifice d'écoulement de la gouttière d'évacuation de l'eau de dégivrage située au milieu du compartiment réfrigérateur pour empêcher l'eau de déborder et de couler sur les aliments qui se trouvent à l'intérieur.
electrolux Anomalie L'ampoule ne fonctionne pas. Le compresseur fonctionne en permanence. Cause possible Remède L'ampoule est en mode veille. Ouvrez et fermez la porte. L'ampoule est défectueuse. Consultez le paragraphe "Remplacement de l'ampoule". La température n'est pas correc- Sélectionnez une température tement réglée. plus élevée. La porte n'est pas correctement fermée. Consultez le paragraphe "Fermeture de la porte". La porte a été ouverte trop souvent.
electrolux 19 5. Rebranchez l'appareil. 6. Ouvrez la porte et vérifiez si l'ampoule fonctionne. Fermeture de la porte 1. Nettoyez les joints de la porte. 2. Si nécessaire, ajustez la porte. Consultez le paragraphe "Installation". 3. Si nécessaire, remplacez les joints défectueux. Contactez le Service Après-vente.
10mm 10mm 100mm 20 electrolux Branchement électrique Contrôlez, avant de brancher l'appareil, si la tension et la fréquence indiquées sur la plaque signalétique correspondent à celles de votre réseau. L'appareil doit être relié à la terre. La fiche du câble d'alimentation comporte un logement pour mise à la terre. Si la prise de courant murale n'est pas mise à la terre, branchez l'appareil sur une prise de terre conformément aux normes en vigueur, en demandant conseil à un électricien qualifié.
electrolux 21 e d 2 1 f d 4 • Retirez la vis du cache charnière (a). • Dévissez la charnière supérieure (b) et enlevez-la. • Dévissez la vis et retirez la butée de porte (c). 5 3 • Remettez l'appareil en position verticale. • Ouvrez la porte et remettez en place la moulure en plastique de la porte supérieure en utilisant les vis. b c a • Enlevez la porte. • Enlevez le cache (e) à l'aide d'un outil, dévissez le gond de la charnière inférieure (f) et placez-le sur le côté opposé.
electrolux Avertissement Après avoir changé le sens d'ouverture des portes, vérifiez que toutes les vis sont correctement serrées et que le joint magnétique adhère bien à l'appareil. Si la température ambiante est basse (en hiver, par exemple), il se peut que le joint n'adhère pas parfaitement. Dans ce cas, attendez que le joint reprenne sa taille naturelle. Couchez l'appareil sur son dos.
electrolux 23 Electrolux. Thinking of you. Mehr zu unserem Denken finden Sie unter www.electrolux.com INHALT 23 25 26 26 26 Reinigen und Pflegen 27 Was tun, wenn … 28 Technische Daten 30 Montage 30 Hinweise zum Umweltschutz 33 Änderungen vorbehalten Lesen Sie zu Ihrer Sicherheit und für die optimale Geräteanwendung vor der Installation und dem Gebrauch des Gerätes die vorliegende Benutzerinformation aufmerksam durch, einschließlich der Ratschläge und Warnungen.
electrolux • Das Kältemittel Isobutan (R600a) im Kältekreislauf des Gerätes ist ein natürliches und sehr umweltfreundliches Gas, das jedoch leicht entflammbar ist. Achten Sie beim Transport und bei der Aufstellung des Gerätes darauf, nicht die Komponenten des Kältekreislaufs zu beschädigen.
electrolux 25 • Kontrollieren Sie nach dem Auspacken das Gerät auf eventuelle Beschädigungen. Nehmen Sie das Gerät nicht in Betrieb, wenn es beschädigt ist. Melden Sie die Schäden umgehend dem Händler, bei dem Sie es erworben haben. Bewahren Sie in diesem Fall die Verpackung auf. • Lassen Sie das Gerät mindestens vier Stunden stehen, bevor Sie es elektrisch anschließen, damit das Öl in den Kompressor zurückfließen kann.
electrolux tur im Innern des Gerätes von verschiedenen Faktoren abhängt: • Raumtemperatur • Häufigkeit der Türöffnung • Menge der eingelagerten Lebensmittel • Standort des Geräts Wichtig! Ist die Umgebungstemperatur hoch oder das Gerät voll beladen, dieses aber auf die niedrigste Temperatur eingestellt, so kann es bei andauerndem Betrieb des Geräts an der Rückwand zu Frostbildung kommen.
electrolux 27 Reif- oder Eisbildung am Verdampfer kommen. Stellen Sie in diesem Fall den Temperaturregler auf eine höhere Einstellung ein, die ein automatisches Abtauen und damit auch einen niedrigeren Energieverbrauch ermöglicht.
electrolux Abtauen des Kühlschranks Bei normalem Betrieb wird Frost bei jedem Anhalten des Motorkompressors automatisch aus dem Verdampfer des Kühlschranks entfernt. Das Tauwasser läuft durch eine Rinne in einen speziellen Behälter an der Rückseite des Geräts über dem Motorkompressor, wo es verdampft. Reinigen Sie deshalb regelmäßig die Abflussöffnung des Tauwassers in der Mitte des Kühlschrankkanals, damit das Wasser nicht überfließt und auf die gelagerten Lebensmittel tropft.
electrolux 29 Störung Die Lampe funktioniert nicht. Der Kompressor arbeitet ständig. Mögliche Ursache Abhilfe Das Gerät bekommt keinen Strom. Es liegt keine Spannung an der Netzsteckdose an. Testen Sie bitte, ob ein anderes Gerät an dieser Steckdose funktioniert. Kontaktieren Sie gegebenenfalls einen qualifizierten Elektriker. Die Lampe befindet sich im Standby-Modus. Schließen und öffnen Sie die Tür. Die Lampe ist defekt. Siehe hierzu „Austauschen der Lampe“.
electrolux geräte geeignet sein muss. (die maximal erlaubte Leistung steht auf der Abdeckung der Lampe). 4. Bringen Sie die Abdeckung der Lampe wieder an, indem Sie sie an ihre ursprüngliche Position zurückschieben. 5. Schließen Sie das Gerät wieder an. 6. Öffnen Sie die Tür und prüfen Sie, ob die Beleuchtung funktioniert. Schließen Sie die Tür 1. Reinigen Sie die Türdichtungen. 2. Stellen Sie die Tür nach Bedarf ein. Siehe hierzu "Montage". 3.
electrolux 31 gen, damit die Tür zum Herausnehmen der Ablagen geöffnet werden kann. 10mm 10mm 100mm Warnung! Es muss möglich sein, das Gerät vom Netz zu trennen. Nach der Installation muss die Steckdose daher zugänglich bleiben. Elektrischer Anschluss Kontrollieren Sie vor der ersten Benutzung des Gerätes, ob die Netzspannung und -frequenz Ihres Hausanschlusses mit den auf dem Typenschild angegebenen Anschlusswerten übereinstimmen. Das Gerät muss geerdet sein.
electrolux • Die Schraube des neuen Scharniers der Abdeckung, die sich ebenfalls im Beutel mit der Anleitung befindet, festziehen. d e 2 1 d 5 f 4 • Lösen Sie die Schraube des Scharnierabdeckstopfens (a). • Schrauben Sie das obere Türscharnier ab und nehmen Sie es ab (b). • Lösen Sie die Schraube und entfernen Sie den Türanschlag (c). 3 • Heben Sie das Gerät in die vertikale Position. • Öffnen Sie die Türe und befestigen Sie die Kunststoffabdeckung der oberen Türe mit den Schrauben.
electrolux 33 Türdichtung nicht richtig am Gerät anliegt. Warten Sie in diesem Fall auf die natürliche Anpassung der Dichtung. Legen Sie das Gerät mit der Rückseite nach unten ab. Warnung! Nach einem Wechsel der Türanschläge stellen Sie bitte sicher, dass alle Schrauben korrekt angezogen sind und die Magnetdichtung fest am Gerät haftet. Bei niedrigen Umgebungstemperaturen (z.B.
electrolux Electrolux. Thinking of you. Per conoscere meglio il nostro modo di pensare, visitate il sito www.electrolux.
electrolux 35 – Aerare bene il locale in cui si trova l'apparecchiatura • È pericoloso cambiare le specifiche o modificare il prodotto in qualunque modo. Un danneggiamento del cavo potrebbe provocare cortocircuiti, incendi e/o scosse elettriche. Avvertenza Tutti i componenti elettrici (cavo di alimentazione, spina, compressore) devono essere sostituiti da un tecnico certificato o da personale d'assistenza qualificato. • • • • 1. Non collegare prolunghe al cavo di alimentazione. 2.
electrolux • Gli interventi di assistenza devono essere eseguiti esclusivamente da tecnici autorizzati e utilizzando solo ricambi originali. • Attorno all'apparecchio vi deve essere un'adeguata circolazione dell'aria, altrimenti si può surriscaldare. Per ottenere una ventilazione sufficiente seguire le istruzioni di installazione.
electrolux 37 Importante Se la temperatura ambiente è elevata o l'apparecchiatura è a pieno carico, un'impostazione alla temperatura minima può causare l'attivazione ininterrotta del compressore e la formazione di brina sulla parete posteriore. In questo caso, impostare una temperatura più elevata per consentire lo sbrinamento automatico e ridurre così il consumo di energia.
electrolux Consigli per la refrigerazione di cibi freschi Per ottenere i migliori risultati: • non riporre nel frigorifero cibi caldi o liquidi in fase di evaporazione • coprire o avvolgere il cibo, in particolare se emana un odore forte • posizionare il cibo in modo che l'aria possa circolare liberamente attorno ad esso Consigli per la refrigerazione Consigli utili: Carne (tutti i tipi): avvolgerla in sacchetti di politene e collocarla sul ripiano di vetro sopra il cassetto delle verdure.
electrolux 39 Periodi di inutilizzo Quando l'apparecchio non è utilizzato per lunghi periodi, adottare le seguenti precauzioni: • scollegare l'apparecchio dalla rete elettrica • rimuovere tutto il cibo • sbrinare 20)e pulire l'apparecchio e tutti gli accessori • lasciare la/e porta/e socchiusa/e per evitare odori sgradevoli. Se l'apparecchio rimane acceso, chiedere a qualcuno di controllare ogni tanto per evitare che il cibo contenuto marcisca in caso di interruzione dell'alimentazione elettrica.
electrolux Problema Possibile causa Soluzione La temperatura ambiente è troppo alta. Abbassare la temperatura ambiente. Scorre acqua sul pannello posteriore del frigorifero. Durante lo sbrinamento automa- Non si tratta di un'anomalia. tico, la brina che si forma sul pannello posteriore si scioglie. Scorre acqua all'interno del frigorifero. Lo scarico dell'acqua è ostruito. Pulire lo scarico dell'acqua. Gli alimenti impediscono all'acqua di scorrere nell'apposito collettore.
electrolux 41 3. Se necessario, sostituire le guarnizioni della porta difettose. Contattare il Centro di assistenza locale. DATI TECNICI Dimensioni Altezza 1600 mm Larghezza 600 mm Profondità I dati tecnici sono riportati sulla targhetta del modello applicata sul lato sinistro inter- 650 mm no dell'apparecchiatura e sull'etichetta dei valori energetici.
electrolux Distanziatori posteriori All'interno dell'apparecchio sono presenti due distanziatori che devono essere montati come illustrato in figura. Allentare le viti e inserire il distanziatore sotto la testa della vite, infine serrare nuovamente le viti. d d • Togliere le viti del tappino copricerniera (a). • Svitare e togliere la cerniera superiore (b). • Svitare la vite e togliere il dispositivo di arresto della porta (c).
electrolux 43 • Fissare la maniglia sul lato opposto, inserire i tappini di plastica nei fori lasciati aperti (inclusi nel sacchetto delle istruzioni). e Avvertenza Riposizionare l'apparecchiatura, livellarla, attendere almeno quattro ore e inserire la spina nella presa. 2 1 5 f 4 3 • Riportare l'apparecchiatura in posizione verticale. • Aprire la porta e riposizionare il frontalino di plastica superiore mediante le viti.
www.electrolux.