Welcome to the world of Electrolux Thank you for choosing a first class product from Electrolux, which hopefully will provide you with lots of pleasure in the future. The Electrolux ambition is to offer a wide variety of quality products that make your life more comfortable. You find some examples on the cover in this manual. Please take a few minutes to study this manual so that you can take advantage of the benefits of your new machine.
Important Safety Information These warnings are provided in the interest of safety. You MUST read them carefully before installing or using the appliance. It is very important that this instruction book should be kept safely for future consultation. If the appliance should be sold or given to another person, please ensure that the booklet goes together with it, so that the new owner can know of the functions of the machine and also be aware of the warnings.
Contents For the User For the Installer Important Safety Information 18 Instruction for the Installer 23 Instruction for the User 20 Technical Data 24 Cleaning and Maintenance 22 Electrical connection 25 Service and original Spare Parts 30 Gas connection 26 Adaptation to different types of gas 27 Building In 28 Possibilities for insertion 29 Guide to Use the instructions The following symbols will be found in the text to guide you throughout the Instructions: Safety Instructions !
Instruction for the User Once the hob has been installed, it is important to remove any protective materials, which were put on in the factory. Hob burners control knobs The hob burners control knobs are situated on the hob right hand side. The symbols on the knobs mean that: there is no gas supply there is maximum gas supply there is minimum gas supply Lighting the burners For easier lighting, proceed before putting a pan on the pan support. ! To light a burner: 1.
Using the hob correctly To ensure maximum burner efficiency, it is strongly recommended that you use only pots and pans with a bottom fitting the size of the burner used, so that flame will not spread beyond the bottom of the vessel (see the table beside and Fig. 2). It is also advisable, as soon as a liquid starts boiling, to turn down the flame so that it will barely keep the liquid simmering. Use only pans or pots with flat bottom. Pots must not enter the control zone.
Cleaning and Maintenance Disconnect the appliance from the electrical supply, before carrying out any cleaning or manteinance work. The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool. This appliance cannot be cleaned with steam or with a steam cleaning machine. General cleaning Wash the enamelled components with warm soapy water.
Instruction for the Installer # # # # The following instructions about installation and maintenance must be carried out by qualified personnel in compliance with the regulation in force. The appliance must be electrically disconnected before all interventions. If any electric supply to the appliance is required to carry out the work, ensure all the necessary precautions are followed. The side walls of the unit in which the hob is going to be installed, must not exceed the height of the working top.
Technical Data Gas Burners Rating Rapid Burner 3,0 kW (Natural gas) - 2,8 kW (Liquid gas) Auxiliary Burner Appliance Class Category Electric supply Setting 1,0 kW 3 II2H3+ 220 V ~ 60 Hz Natural Gas 20 mbar Gas connection G 1/2" Hob recess dimensions Length Width 24 490 mm 270 mm
Electrical connection The appliance is designed to be connected to 220 V monophase electricity supply. The connection must be carried out in compliance with the laws and regulations in force.
Gas connection Choose fixed connections or use a flexible pipe in stainless steel in compliance with the regulation in force. If using flexible metallic pipes, be careful they do not come in contact with mobile parts or they are not squeezed. Use the same attention when the hob is combinated with an oven. IMPORTANT - To ensure a correct operation, a saving of energy and the long life of the appliance, the voltage pressure of the appliance must correspond to the recommended values.
Adaptation to different types of gas Injectors replacement ! • Remove the pan supports. • Remove the burner's caps and crowns. • With a socket spanner 7 unscrew and remove the injectors (Fig. 7), and replace them with the ones required for the type of gas in use (see table 2). • Reassemble the parts, following the same procedure backwards. • Replace the rating label (placed near the gas supply pipe) with the relevant one for the new type of gas supply.
Building In R A 51 0 29 0 Fig. 9 Dimensions are given in millimeters This hob can be inserted in a built-in kitchen unit whose depth is between 550 and 600 mm. The hob dimensions are shown in figure 9. The edge of the cut out must have a minimum distance from the rear wall of 55 mm. If there are side walls, or sides of the furniture unit near the hob, the cut out edges must have a minimum distance of 100 mm.
Possibilities for insertion Kitchen unit with door Proper arrangements must be taken in designing the furniture unit, in order to avoid any contact with the bottom of the hob which can be heated when it is operated. The recommended solution is shown in Fig. 12. The panel fitted under the hob should be easily removable to allow an easy access if a technical assistance intervention is needed. Kitchen unit with oven The hob recess dimensions must comply the indication given in Fig.
Service and original Spare Parts Before leaving the factory this appliance was tested and verified by specialized personnel, in order to ensure best performance. Any repair work which needs to be carried out should be done with the utmost care and attention. For this reason we recommend that for any problem you contact the dealer who sold it to you, or our nearest authorized Service Centre, specifying the nature of the problem, the appliance model (Mod.), the product number (Prod. No.
31
04/07 Grafiche MDM - Forlì www.electrolux.co.
