Gas hobs INSTR UCTION BOOKLET INSTRUCTION Please read this instruction booklet before using the appliance Mod.
English Important Safety Information These warnings are provided in the interest of safety. You MUST read them carefully before installing or using the appliance. About Installation, Cleaning and Manteinance • • It is mandatory that all operations required for the installation are carried out by a qualified or competent person, in accordance with existing rules and regulations. Disconnect the appliance from the electrical supply, before carrying out any cleaning or manteinance work.
Contents For the User Important Safety Information 2 Instruction for the User 4 Cleaning and Maintenance 6 For the Installer Technical Data 7 Instruction for the Installer 7 Electrical Connection 8 Adaptation to different types of gas 9 Building In 10 Possibilities for insertion 11 Guide to Use the instructions The following symbols will be found in the text to guide you throughout the Instructions: Safety Instructions Step by step instructions for an operation Hints and Tips Environmental
Instruction for the User Once the hob has been installed, it is important to remove any protective materials, which were put on in the factory. Hob burners control knobs The hob burners control knobs are situated on the hob right hand side. The symbols on the knobs mean that: there is no gas supply there is maximum gas supply there is minimum gas supply Lighting the burners For easier lighting, proceed before putting a pan on the pan support.
Use of electric plates Using the plate correctly To switch on the plate, turn the relevant knob to the required position. The plates are regulated by a 7 position switch: Position 0: off Position 1: minimum disbursement of heat Position 6: maximum disbursement of heat Saucepans and frying pans (Fig.2) - Saucepans and frying pans should not be smaller than the cooking zone, and preferably not more than 10-15 mm larger than the diameter of the cooking zone.
Cleaning and Maintenance Disconnect the appliance from the electrical supply, before carrying out any cleaning or manteinance work. FO 2265 General cleaning Wash the enamelled components with warm soapy water. Never use abrasive cleaners. Frequently wash the "caps" and the "crowns" with hot soapy water, carefully taking away any built-up of food. The cap and crown of each burner are secured with two screws.
Technical Data Gas Burners Rating Electric hotplate Rapid Burner 2,9 kW (G20) - 2,7 kW (G30/G31) Semirapid Burner 1,9 kW Auxiliary Burner 1,0 kW Appliance Class 3 Category II2H3+ (Mod. EGM 636) (Mod. EGM 626) Ø 180 mm. Ø 180 mm. Ø 145 mm.
Electrical Connection The appliance is designed to be connected to 230 V monophase electricity supply. YES The connection must be carried out in compliance with the laws and regulations in force.
Adaptation to different types of gas Injectors replacement • Remove the pan supports. • Remove the burner's caps and crowns. • With a socket spanner 7 unscrew and remove the injectors (Fig. 7), and replace them with the ones required for the type of gas in use (see table 2). • Reassemble the parts, following the same procedure backwards. • Replace the rating label (placed near the gas supply pipe) with the relevant one for the new type of gas supply.
Building In P A SR P P SR 580 580 R R 51 0 51 0 ,5 615 ,5 615 Mod. EGM 636 Mod. EGM 626 Dimensions are given in millimeters A SR R P = Auxiliary burner = Semirapid burner = Rapid Burner = Electric plate These hobs can be inserted in a built-in kitchen unit whose depth is between 550 and 600 mm. The hobs dimensions are shown in the relevant diagram. The edge of the cut out must have a minimum distance from the rear wall of 55 mm.
Possibilities for insertion Kitchen unit with door Kitchen unit with oven Proper arrangements must be taken in designing the forniture unit, in order to avoid any contact with the bottom of the hob which can be heated when it is operated. The recommended solution is shown in Fig. 12. The panel fitted under the hob should be easily removable to allow an easy access if a technical assistance intervention is needed. The hob recess dimensions must comply the indication given in Figs.
