Wiring Diagram

3
Demo Mode/Washer Error Codes
Washer Error Codes
Demo Mode:
The Demo works in two ways: Interactive Mode and Automatic Loop.
The Interactive Mode enables the customer to use the interface
without activating the appliance. The machine behavior appears similar
to normal operation. With the door closed, pressing start, the appliance
turns on and the display counts down by the second from the maximum
time displayed with its respective cycle. The appliance turns off when it
reaches “
”.
The Automatic Loop will engage if no one interacts with the user inter-
face for 3 minutes, or the start button hasn’t been pressed. The machine
will simulate a cycle execution on the display only.
Entering Demo Mode:
1 Press power and look for console light up.
2 For Rotary Dial Cycle Select Washer: Within 10 seconds select
fast wash and then simultaneously press and hold temp and select
(set) buttons for 3 secs. Skip to Step 4.
3 For Push Button Cycle Select Washer: Within 10 seconds select
rinse & spin and then simultaneously press and hold temp and
select (set) buttons for 3 secs. Continue to Step 4.
4 The message “
” will blink 3 times in the center display.
5 If “
” message does not appear, turn off machine and repeat
previous steps.
Exiting Demo Mode:
1 Press power to turn the unit OFF.
2 Press power to turn the unit ON. The unit display will flash “
”
3 times on the numeric display.
3 Within 10 seconds perform steps 4 and 5.
4 Rotate cycle selector ring (on some models) or repeatedly press
cycle button to the 6th position.
5 Press and hold temp and select (set) simultaneously for 3 seconds.
The appliance will beep once, the numeric display will cycle OFF and
ON. The appliance will then beep with the normal power on sequence.
You may also perform factory default reset. See below.
Error
Code
Error Description Display
Notification
Next Step
11 Fill time too long Yes Refer to test (1)
13 Water leak in tub or in pressure sensor No Refer to test (2)
21 Water not pumping out fast enough Yes Refer to test (3)
23 Drain triac error No Refer to test (3)
24 Drain triac error sensing No Refer to test (3)
31 Electronic pressure switch error No Refer to test (4)
32 Pressure sensor calibration problem No Refer to test (4)
35 Pressure sensor indicates water overfill Yes Refer to test (5)
38 Air trap clogged No Refer to test (5)
41 Control board thinks the door switch is open Yes Refer to test (6)
42 Door lock device failure No Refer to test (6)
43 Door lock triac failure No Refer to test (6)
44 Door closed sensing failure No Refer to test (6)
45 Line door sensing failure No Refer to test (6)
55
(select models)
Motor under speed
(not available on 300 series)
No Check for heavy or unbalanced load
Refer to test (9)
57 High current on inverter (motor control) No Refer to test (8)
58 High current on motor phase No Refer to test (8)
59 No spin signal for 3 seconds No Refer to test (9)
5A High temperature on control due to overload (motor control) No Refer to test (8)
5B Motor control under voltage No Check supply under load and wiring to unit
Refer to tests (6 and 9)
To return to factory settings,
press the soil and options buttons at
the same time and hold until the signal
sounds.
Recalling Last Error Code:
1 Press power and look for console light up.
2 Wait at least 10 seconds, then simultaneously press and hold temp
and select (set) buttons for 3 secs.
3 The display will show the last error in memory.
4 Clear the display and return to normal operation by touching any
button or by pressing the power button.
NOTE
Once Demo Mode is activated, every time the machine is turned on,
Demo Mode is automatically recalled; this occurrence is signaled at
the start-up by the text “
” flashing 3 times in the center display.
Unplugging the unit will not clear Demo Mode. See “Exiting Demo
Mode” for more information.
Factory Default Reset:
1 Press power and look for console light up.
2 Wait at least 10 seconds, then simultaneously press and hold soil
and options buttons for 3 secs.