E784F303BI EN Washing Machine User Manual
www.electrolux.com CONTENTS 1. SAFETY INFORMATION....................................................................................3 2. SAFETY INSTRUCTIONS..................................................................................4 3. INSTALLATION.................................................................................................. 6 4. PRODUCT DESCRIPTION.............................................................................. 16 5. CONTROL PANEL...............................
ENGLISH 1. 3 SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible for any injuries or damages that are the result of incorrect installation or usage. Always keep the instructions in a safe and accessible location for future reference. 1.
www.electrolux.com by clients in hotels, motels, bed & breakfast and other residential type environments; – areas for communal use in blocks of flats or in launderettes. Do not exceed the maximum load of 8 kg (refer to the "Programme chart" chapter). The operating water pressure at the water entry point from the outlet connection must be between 0.5 bar (0.05 MPa) and 8 bar (0.8 MPa). The ventilation opening in the base must not be covered by a carpet, mat, or any floor covering.
ENGLISH • • • • • • • than 0°C or where it is exposed to the weather. The floor area on which the appliance is to be installed must be flat, stable, heat resistant and clean. Make sure that there is air circulation between the appliance and the floor. When the appliance is in its permanent position, check if it is levelled correctly with the aid of a spirit level. If it is not, adjust the feet accordingly. Do not install the appliance directly above a floor drain.
www.electrolux.com • Do not touch the glass door while a programme is in operation. The glass can get hot. 2.5 Service • • To repair the appliance contact an Authorised Service Centre. Use original spare parts only. 2.6 Disposal WARNING! Risk of injury or suffocation. • • • • Disconnect the appliance from the mains electrical and water supplies. Cut off the mains electrical cable close to the appliance and dispose of it.
ENGLISH 7 1. Put two polystyrene packaging elements on the floor under the appliance. WARNING! It is strongly recommended that this action is carries out by two persons. 2. Carefully put the appliance down on its rear side. Make sure not to damage the hoses. 3. Remove the polystyrene protection from the bottom. 1 2 4. Return the appliance in vertical position and remove the socket polystyrene protection. 1 2 5. Remove the power supply cable and the drain hose from the hose holders.
www.electrolux.com 6. Remove the three bolts, the hose holders and plastic spacers by using the spanner supplied with the appliance. F 7. Close the holes with the plastic caps you find in the user manual bag. Put the smallest cap F in upper hole and the two bigger caps G in lower holes. G We recommend that you keep the packaging and the transit bolts for any movement of the appliance. 3.4 Installation on suspended flooring Suspended wooden floors are particularly susceptible to vibration.
ENGLISH 3.5 Positioning and levelling 1. Install the appliance on a flat hard floor. WARNING! Make sure that carpets do not stop the air circulation below the appliance. Bring the appliance near the furniture recess before levelling it. For more details, refer to paragraph "Building in". x4 2. Loosen or tighten the feet to adjust the level. A correct adjustment of the appliance level prevents the vibration, noise and the movement of the appliance when in operation.
www.electrolux.com The inlet hose 1. Remove the inlet hose from inside the drum. 2. To connect the water inlet hose towards the proper direction and with the proper inclination, check the position of the water tap before connecting it to the back of the appliance. Make sure the hose is nor kinked, squashed but neither tensed. 45 20 O O 3. Connect the hose to the back of the appliance. Do not turn the inlet hose downwards, but turn it left or right depending on the position of your water tap. 4.
ENGLISH 11 To a stand pipe with vent-hole Directly into a drain pipe at a height of not less than 60 cm (23.6”) and not more than 100 cm (39.3”). The end of the drain hose must always be ventilated , i.e. the inner diameter of the drain pipe (min. 40 mm - min. 1.6”) must be larger than the external diameter of the drain hose. Ø 40 mm max.600 mm To a sink spigot Put the drain hose in the spigot and tighten it with the supplied cable tie L.
www.electrolux.com 596 mm If hoses run behind the appliance, make sure that nothing closes the small recess indicated with the measures 50 x 50 mm. 553 mm 819 mm 50 mm 50 mm 140 mm 76 mm The appliance is also equipped with an adhesive sponge pad H that you can find inside the drum. Attach it on the top of the appliance where indicated in the drawing. When levelling the appliance under the furniture, DO NOT squeeze the sponge pad.
ENGLISH 13 1. Remove the screws of the top cover on the rear of the appliance and install the anti-tilting device as shown in the drawing. ~10mm 2. Adjust the anti-tilting device so that the distance from the counter is 10mm. Loosen the nut counterclockwise with a 3mm wrench. Adjust the height and turn the nut clockwise to fix it. 3.9 Preparation and assembly of the cupboard door The dimensions of the cupboard door should be: • width min. 595 - max. 598 mm; • thickness 16-22 mm.
www.electrolux.com Reversibility of the cupboard door Carry out the cupboard door reversibility before the appliance is built in completely. N M If the cupboard door has to be opened from left to right, invert the position of the hinge supports M with the magnetic plate N and lower plate O. O M N Make sure that the plate with magnet is on the upper position. O Cupboard door preparation For countersinking the door, it is recommended to call a professional.
ENGLISH 15 Set the position of the lower hole respecting dimensions and distances shown in the drawing (449 mm). Countersink the holes. 16-22 mm Ø 35 mm 449 mm 12,5 - 14 mm 22±1,5 mm 595-598 mm A Hinges To mount the hinges it is necessary to drill two holes (dia. 35 mm, depth 12.5 - 14 mm depending on the depth of cupboard door) on the inner side of the door. The hinges will be fixed to the door by means of the four supplied screws A.
www.electrolux.com Counter-magnet The appliance is pre set for a magnetic closure. For a correct closure: 1. Position the screw C and the countermagnet D on the magnetic plate N. Lean the cupboard door against the screw until it leaves a mark. 2. Open the cupboard door and screw the counter-magnet D (steel disk + rubber ring E) with the screw C in the inner side of the cupboard door, where the screw left the mark as described in the first step. 1 N 2 E D C 4. PRODUCT DESCRIPTION 4.
ENGLISH 5. CONTROL PANEL 5.1 Control panel description 1 Wool/Silk Denim Outdoor Sport Rapid 14min 2 5 6 7 Cottons Manager Synthetics Delicates Anti-allergy Duvet Steam Rinse Spin/Drain Programme dial Spin touch button Temp. touch button Display Delay Start touch button Time Manager touch button Start/Pause touch button 8 Plus Steam touch button and permanent Child Lock option 5.
www.electrolux.com The Temperature area: Temperature indicator . Cold water indicator. Child safety lock indicator. Door locked indicator. Delay start indicator. The digital indicator can show: • Programme duration (e. g. • Delay time (e. g. • Cycle end ( ). ). ). • Warning code (e.g. • Error indicator ( ). ). Time Manager indicator. Steam phase indicator. Anti-crease phase indicator. Drum clean indicator. This is a recommendation to perform the drum cleaning.
ENGLISH 19 6. DIAL AND BUTTONS 6.1 Introduction The options/functions are not available with all washing programmes. Check the compatibility between options/functions and washing programmes in the "Programme Chart". An option/function can exclude another one, in this case the appliance doesn't allow you to set incompatible options/ functions. 6.5 Spin When you set a programme, the appliance automatically sets the maximum spin speed allowed, except for programme Denim.
www.electrolux.com As the programme is very quiet, it is suitable for use at night time when cheaper electricity tariffs are available. In some programmes the rinses are performed with more water. If you touch the Start/Pause button, the appliance performs the only draining phase. The appliance empties the water out automatically after 18 hours approximately. 6.6 Prewash With this option you can add a prewash phase to a washing programme. The corresponding indicator above the touch button illuminates.
ENGLISH To activate/deactivate this option, hold down the Plus Steam button until comes on/goes off on the display. The Time Manager is available only with the programmes in the table. indicator Cottons The appliance will default to this option after you switch it off. The Child Lock function may not be available for a few seconds after switching the appliance on. 1) 6.12 Delay Start With this option you can delay the start of a programme to a more convenient time.
www.electrolux.com 7. PROGRAMMES 7.1 Programme Chart Programme Default tem‐ perature Temperature range Reference spin speed Spin speed range Maxi‐ mum load Programme description (Type of load and soil level) Washing programmes Cottons 40 °C 90 °C - Cold Cottons Eco1) 40 °C 60 °C - 40 °C Synthetics 40 °C 60 °C - Cold Delicates 30 °C 40 °C - Cold Anti-allergy 60 °C 1400 rpm 8 kg (1400- 400 rpm) White cotton and coloured cotton. Normal, heavy and light soil.
ENGLISH Programme Default tem‐ perature Temperature range Reference spin speed Spin speed range Maxi‐ mum load 1 kg Steam - 23 Programme description (Type of load and soil level) Cottons, Synthetics, Delicates. Short and gentle steam programme to refresh even your very delicate garments, including very delicate garments with sequins, lace etc. When treat‐ ing smaller loads, the programme duration can be further reduced by means of the Time Manager option.
www.electrolux.com Programme Default tem‐ perature Temperature range Outdoor 30 °C 40 °C - Cold Reference spin speed Spin speed range Maxi‐ mum load Programme description (Type of load and soil level) 1200 rpm 2 kg4) (1200- 400 1 kg5) rpm) Do not use fabric softener and make sure that there is no soften‐ er residue in the detergent dis‐ penser. Synthetic sport items.
ENGLISH Programme Default tem‐ perature Temperature range Wool/Silk 40 °C 40 °C - Cold Reference spin speed Spin speed range 1200 rpm (1200 400 rpm) Maxi‐ mum load 1.5 kg 25 Programme description (Type of load and soil level) Machine washable wool, hand washable wool and other fabrics with «hand washing» care symbol6). 1) Standard programmes for the Energy Label consumption values.
Rapid 14min ■ ■ ■ Sport ■ ■ ■ Outdoor ■ ■ ■ Denim ■ ■ ■ Wool/Silk ■ ■ ■ Time Manager Delay Start Plus Steam3) Soft Plus Extra Rinse Prewash1) Spin Programme Stains 2) www.electrolux.com No Spin 26 ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ 1) Prewash and Stains cannot be selected together. 2) This option is not available with temperature lower than 40 °C. 3) This option is not available with temperature lower than 40 °C.
ENGLISH 27 9. BEFORE FIRST USE 1. Make sure that the electrical power is available and the water tap is open. 2. Pour 2 litres of water into the detergent compartment marked by . This action activates the drain system. 3. Pour a small quantity of detergent into the compartment marked by 4. Set and start a programme for cotton at the highest temperature without any laundry in the drum. This removes all possible dirt from the drum and the tub. . 10. DAILY USE WARNING! Refer to Safety chapters. 10.
www.electrolux.com - Maximum level for quantity of liquid additives. gent. - Flap for powder or liquid deter‐ Always follow the instructions that you find on the packaging of the detergent products, but we recommend that you do not exceed the maximum indicated level ( ). This quantity will however guarantee the best washing results. After a washing cycle, if necessary, remove any detergent residue from the detergent dispenser.
ENGLISH display and the given information changes accordingly. If a selection is not possible an acoustic signal sounds and the display shows . 10.6 Starting a programme Touch the Start/Pause button to start the programme. It is not possible to start the programme when the indicator of the button is off and doesn't flash (e.g. programme dial on a wrong position). The related indicator stops flashing and stays on. The programme starts, the door is locked. The display shows the indicator .
www.electrolux.com About 20 minutes after the programme start, the programme duration could be adjusted again depending on the capacity of water absorption of the fabrics. The SensiCare detection is carried out with complete washing programmes only and if the programme duration has not been reduced by means of the Time Manager button. 10.9 Interrupting a programme and changing the options There is also an alternative way of cancelling: 1. Rotate the selector knob to the "Reset" position . 2.
ENGLISH 2. 3. 4. 5. When you activate the appliance again, the display shows the end of the previous programme. Turn the programme dial to set a new cycle. Remove the laundry from the appliance. Make sure that the drum is empty. Keep the door and the detergent dispenser slightly ajar to prevent mildew and odours. Close the water tap. 10.
www.electrolux.com • • • • • • • Turn multilayered fabrics, wool and items with printed illustrations inside out. Pre-treat tough stains. Wash heavy soil stains with a special detergent. Be careful with curtains. Remove the hooks and put the curtains in a washing bag or pillowcase. Do not wash laundry without hems or with cuts. Use a washing bag to wash small and/or delicate items (e.g. underwired bras, belts, tights, etc. ).
ENGLISH 12.1 External cleaning Clean the appliance with mild soap and warm water only. Fully dry all the surfaces. 33 drained out with the water, in such a way that there is no need by the customer to access this area for regular maintenance and cleaning. CAUTION! Do not use alcohol, solvents or chemical products. CAUTION! Do not clean the metal surfaces with chlorine-based detergent. 12.
www.electrolux.com Occasionally, at the end of a cycle the display may show the icon : this is a recommendation to perform the “drum cleaning”. Once the drum cleaning has been performed, the icon disappears. 12.6 Cleaning the detergent dispenser To prevent possible deposits of dried detergent or clotted fabric softener and/or formation of mould in the detergent dispenser drawer, once in a while carry out the following cleaning procedure: 3.
ENGLISH Regularly check the drain pump filter and make sure that it is clean. Clean the drain pump if: • The appliance does not drain the water. • The drum does not turn. • The appliance makes an unusual noise because of the blockage of the drain pump. • 35 The display shows the alarm code . WARNING! • Do not remove the filter while the appliance operates. • Do not clean the pump if the water in the appliance is hot. Wait until the water cools down Proceed as follows to clean the pump: 2 1.
www.electrolux.com 180˚ 3. Turn the filter 180 degrees in anti-clockwise direction to open it, without removing. Let the water flow out. 4. When the bowl is full of water, turn the filter back and empty the container. 5. Repeat the steps 4 and 5 until the water stops to flow out. 1 6. Turn the filter anti-clockwise to remove it 2 7. If it is necessary, remove fluff and objects from the filter recess. Make sure that the impeller of the pump can rotate.
ENGLISH 37 2 9. Put the filter back into the special guides by turning it clockwise. Make sure that you tighten the filter correctly to prevent leakages. 1 2 10. Close the pump cover. 1 When you drain the water with the emergency drain procedure, you must activate the drain system again: 1. Put 2 litres of water in the main wash compartment of the detergent dispenser. 2. Start the programme to drain the water. 12.
www.electrolux.com 45° 20° 12.9 Emergency drain If the appliance cannot drain the water, carry out the same procedure, described in 'Cleaning the drain pump' paragraph. If necessary, clean the pump. When you drain the water with the emergency drain procedure, you must activate the drain system again: 1. Put 2 litres of water in the main wash compartment of the detergent dispenser. 2. Start the programme to drain the water. 12.
ENGLISH 39 • - No communication between electronic elements of the appliance. Switch it off and switch on again. The programme was not finished properly or the appliance stopped too early. If the alarm code appears again, contact the Authorised Service Centre. • - The anti-flood device is on. Disconnect the appliance and close the water tap. Contact the Authorised Service Centre. • - The appliance does not fill with water properly.
www.electrolux.com Problem Possible solution • • • The appliance does not • fill with water properly. • • Make sure that the water tap is open. Make sure that the pressure of the water supply is not too low. For this information, contact your local water authority. Make sure that the water tap is not clogged. Make sure that the inlet hose has no kinks, damages or bends. Make sure that the connection of the water inlet hose is correct.
ENGLISH Problem Possible solution • The appliance makes an unusual noise and vibrates. The programme dura‐ tion increases or de‐ creases during pro‐ gramme execution. • • Make sure the levelling of the appliance is correct. Refer to "Installation instruction". Make sure that the packaging and/or the transit bolts are removed. Refer to "Installation instruction". Add more laundry in the drum. The load may be too small.
www.electrolux.com 1. Press the On/Off button to switch the appliance off. 2. Disconnect the mains plug from the mains socket. 3. Pull twice the emergency unlock trigger downward and open the appliance door. The emergency unlock trigger is located where indicated by the following picture. 4. Take out the laundry and then close the appliance door. 14. CONSUMPTION VALUES Stated values are obtained in laboratory conditions with relevant stand‐ ards.
ENGLISH Programmes Load (kg) Energy con‐ sumption (kWh) Water con‐ sumption (litre) 43 Approxi‐ Remain‐ mate pro‐ ing mois‐ gramme ture (%)1) duration (minutes) Standard cotton programmes Standard 60°C cotton 8 0.82 54 295 52 Standard 60°C cotton 4 0.56 39 235 52 Standard 40°C cotton 4 0.53 40 235 52 1) At the end of spin phase. Off Mode (W) Left On Mode (W) 0.30 0.
www.electrolux.com 16. PRODUCT INFORMATION SHEET IN REFERENCE TO E.U. REGULATION 1369/2017 Product Information Sheet Trade Mark ELECTROLUX Model E784F303BI, PNC914580000 Rated capacity in kg Energy efficiency class 8 A+++ Energy consumption in kWh per year, based on 220 standard washing cycles for cotton programmes at 60 °C and 40 °C at full and partial load, and the con‐ sumption of the low-power modes. Actual energy con‐ sumption will depend on how the appliance is used.
ENGLISH Programme time of the "standard 40°C cotton pro‐ gramme at partial load in minutes 235 Duration of the left on mode in minutes 5 Airborne acoustical noise emission in db(A) washing 46 Airborne acoustical noise emission in db(A) spinning 68 Built in appliance Y/N 45 Yes The information given in the chart above is compliant with the EU Commission regulation 1015/2010 implementing directive 2009/125/EC . 17. ENVIRONMENTAL CONCERNS Recycle materials with the symbol .
www.electrolux.
ENGLISH 47
157018020-B-292018 www.electrolux.
