Installation guide

ManualsBrandsElectrolux ManualsMicrowaveOfficial Electrolux electric oven

iNSTALLATiON AND SERVICE MUST BE PERFORMED BY A QUALiFiED iNSTALLER.

iMPORTANT: SAVE FOR LOCAL ELECTRICAL iNSPECTOR'S USE.

READ AND SAVE THESE iNSTRUCTiONS FOR FUTURE REFERENCE.

The electrical requirements for this oven are 240 volts, 15 amps.

The oven has a 6-15 pJug and requires a 6-15 receptacle.

NOTE:

1. Base must be capable of supporting 200

pounds (90.7 kg).

2. Make sure base is level and front of cabinet

is square. Ifthe cabinet base is not level, the

oven will tend to slide out when opening

the door.

3. Minimum required distance is 36" (91.44

cm) from the floor.

4. At the rear of the opening, provide a 3

pronged, polarized, electrical outlet, 240

volt A.C., 15 amp. or larger. This outlet

should not be located in the shaded area

of Figure I. It is exceedingly important that

the outlet be 240 volts and 15 amps. for

optimum oven performance.

5. Minimum required distance between the

high speed oven and the wall oven should

be 3-inches.

Remov

shipping supports _ Replace these

(both sides) screws after

shipping support

removal (both sides)

Figure 1

30" (76.2) High Speed

Oven 30" (76.2) 2227/32" (58.0) 21%" (54.0) 221s/16" (58,2)

30" (76.2) High Speed 22%" (56.8) 22%" (57.5) 24" (61.0) rain. 21"/_/(55.1) 21 _s/_6"(55.7) 30" (76.2) min.

Oven

All dimensions are in inches (cm).

Important Notes to the Installer

I. Read all instructions contained in these installation

instructions before installing the high speed oven.

2. Removeallpacking materialfrom the ovencompartments

before connecting the electrical supply to the high speed

oven. Remove the 2 shipping duct supports (seefigure

1)by removing the 4 screws securing them. Reinsert 2

screws (each side) to secure the stainless cover.

3. Observe all governing codes and ordinances.

4. Be sure to leave these instructions with the consumer.

Important Note to the Consumer

Keep these instructions with your Owner's Guide for future

reference.

Printed in United States TINSEB424MRRO

Summary of content (4 pages)

PAGE 1
iNSTALLATiON AND SERVICE MUST BE PERFORMED BY A QUALiFiED iNSTALLER. iMPORTANT: SAVE FOR LOCAL ELECTRICAL iNSPECTOR'S USE. READ AND SAVE THESE iNSTRUCTiONS FOR FUTURE REFERENCE. The electrical requirements for this oven are 240 volts, 15 amps. The oven has a 6-15 pJug and requires a 6-15 receptacle. NOTE: 1. Base must be capable of supporting 200 pounds (90.7 kg). 2. Make sure base is level and front of cabinet is square.
PAGE 2
iMPORTANT SAFETY iNSTRUCTiON • Never use your high speed oven for warming or heating the room. Prolonged use of the high speed oven without adequate ventilation can be dangerous. 3. Cabinet The high Refer to figure 1 for the dimensions applicable to your appliance, and the space necessary to receive the oven. The oven support surface may be solid plywood or similar material, however the surface must be level from side to side and from front to rear. 2.
PAGE 3
Cutout _'_ 2 _" Dimensions (56.8 cm) Min. _ 22s_"(57.5 cm) Max2 [ [ [ Anti-Tip Brackets/j 21u/ld' (55.1 cm) Min. 141/2 '' 2115/1d' (36.83 cm) (55.7 cm) Max. Recommended Cutout Width is 22 V2" (57.2 cm) Figure 2 Figure Model 3 and Serial Number Location The serial plate is located on the oven faceplate. When ordering parts for or making inquires about your oven, always be sure to include the model and serial numbers and a lot number or letter from the serial plate on your Before oveR.
PAGE 4
NOTES