BM135H107 01533 Instruction manual Manuel d’instructions Manuale di istruzioni Please read these instructions carefully and make sure you understand them before using this machine. Merci de lire trés attentivement le manuel d'instructions. Assurez-vous d'avoir tout compris avant d'utiliser ce tracteur. Prima di utilizzare la macchina leggete queste istruzioni con attenzione ed accertatevi di averle comprese bene.
1 Safety rules. Sicherheitsvorschriften. Règles de sécurité. Reglas de seguridad. Norme antinfortunistiche. Veiligheidsregels. 2 Assembly. Zusammenbau. Montage. Montaje. Montaggio. Montering. 18 3 Functional description. Funktionsbeschreibung. Description du fonctionnement. Descripción del funcionamiento. Funzionamento. Beschrijving van functies. 26 4 Before starting. Maßnahmen vor dem Anlassen. Avant de démarrer. Antes del arranque. Prima dell’avviamento. Maatregelen vóór het starten.
1. Veiligheidsregels Veilige bedieningsmethoden voor zittrekkers BELANGRIJK: DEZE MAAIMACHINE KAN HANDEN EN VOETEN AMPUTEREN EN VOORWERPEN WEGSLINGEREN. HET NIET OPVOLGEN VAN DEZE VEILIGHEIDSINSTRUCTIES KAN ERNSTIG OF DODELIJK LETSEL TOT GEVOLG HEBBEN. I. TRAINING III. BEDIENING • Lees de instructies aandachtig. Zorg dat u vertrouwd bent met de bedieningselementen en het juiste gebruik van de machine. • Laat kinderen of mensen die niet bekend zijn met de instructies, de maaimachine niet gebruiken.
BM135H107 • • • - nadat u een ongewenst voorwerp heeft geraakt. Inspecteer de maaimachine op schade en voer reparaties uit voordat u de machine weer start en gebruikt; - als de machine abnormaal begint te trillen (onmiddellijk controleren). - vor dem Entfernen von Verstopfungen aus dem Mähwerk oder dem Auswurf; Schakel de aandrijving naar de hulpstukken uit tijdens transport of als ze niet worden gebruikt.
These symbols may appear on your machine or in the literature supplied with the product. Learn and understand their meaning. Diese Symbole finden Sie auf Ihrer Maschine oder in Unterlagen, die mit dem Produkt ausgehändigt wurden. Bitte machen Sie sich mit deren Bedeutung vertraut. Ces symboles peuvent figurer sur tracteur ou dans les publications fournies avec le produit. Apprenez à comprendre la signification de ces symboles.
These symbols may appear on your machine or in the literature supplied with the product. Learn and understand their meaning. Diese Symbole finden Sie auf Ihrer Maschine oder in Unterlagen, die mit dem Produkt ausgehändigt wurden. Bitte machen Sie sich mit deren Bedeutung vertraut. Ces symboles peuvent se montrer sur votre machine ou dans les publications fournies avec le produit. Apprenez à comprendre la signification de ces symboles.
GEFAHR AUGEN SCHÜTZEN EXPLOSIVE GASE KÖNNEN ERBLINDUNG UND KÖRPERVERLETZUNGEN VERURSACHEN. ZU VERMEIDEN: • FUNKEN • FEUER • RAUCHEN SCHWEFELSÄURE KANN ERBLINDUNG ODER SCHWERE VERÄTZUNGEN VERURSACHEN. GEVAAR OGEN BESCHERMEN EXPLOSIEVE GASSEN KUNNEN BLINDHEID OF LETSEL VEROORZAKEN. GEEN • VONKEN • VUUR • ROKEN ZWAVELZUUR KAN BLINDHEID OF ERNSTIGE BRANDWONDEN VER-OORZAKEN. OGEN ONMIDDELLIJK MET WATER SPOELEN. SNEL MEDISCHE HULP INROE-PEN.
2. Assembly. 2. Zusammenbau. 2. Montage. 2. Montaje 2. Montaggio. 2. Montering. Before the tractor can be used certain parts must be assembled, which for transportation reasons are enclosed in the packing. Antes de poder utilizar el tractor, hay que montar algunas piezas que, por razones de transporte, van empaquetadas en el embalaje. Vor der Anwendung des Aufsitzmähers müssen gewisse Teile eingebaut werden, die aus Transportgründen in der Verpackung lose beigefügt sind.
2 • • Monte una arandela plana grande una terercas de 1/2 y apriete en forma segura. Presione la pieza inserta adentro del centro del volante de dirección. 1. EJE DE EXTENCIÓN VOLANTE • • 1 • • • Montare l'albero di estensione (1). Stringere saldamente. Montare il coperchio del piantone. Controllare che tutti i pemi di guida entrino nei rispettivi alloggi. Rimuovere l’adattatore del volante dal volante e scorrerlo sull’estensione dell’albero dello sterzo.
2 Asiento Remueva la manilla de ajuste y la arandela plana que aseguran el asiento al empaque de cartón y póngalos de lado para poder utilizarlos durante la instalación del asiento sobre el tractor. Gire el asiento hacia arriba y remuevalo del embalaje de cartón . Remueva y desechese del embalaje de cartón. Colocar el asiento y en el asiento del recipiente de manera que la cabeza del bulón de la espalda esté posicionada en el agujero ancho ranurado en el recipiente.
2 1. Asiento 2. Cubierta Terminal 3. Cable 4. Cable Instalación de la batería NOTA: Si utiliza la batería después del mes y año indicado sobre la etiqueta, cargue la batería por un mínimo de una hora a 6-10 amps. ADVERTENCIA: Antes de instalar la batería, despójese de brazaletes metálicos, correas de reloj, sortijas, etc. Si estos objetos tocan la bateria pueden producirse quemaduras. A. Frontal de tractor 5. Protección 6. Terminal de batería 7.
2 WARNING: Positive terminal must be connected first to prevent sparks from accidental grounding. Remove terminal caps and discard. Connect the red cable to + and then the black earth cable to -. Screw tight the cables. Grease the battery poles with vaseline to prevent corrosion. WARNUNG! Um einen Kurzschluß zu vermeiden, muß der Pluspol zuerst angeschlossen werden. Die Schutzkappen von den Anschlußklemmen entfernen und entsorgen. Zuerst das rote Kabel an + und dann das schwarze Kabel an - anschließen.
PARA AJUSTAR LAS RUEDAS CALIBRADORAS Las ruedas calibradoras están bien ajustadas cuando se encuentran un poco a distancia del terreno al mismo tiempo que la segadora esté a la altura de corte deseada. Entonces las ruedas calibradoras mantienen el conjunto segador en posición para prevenir el corte raspeo en casi todos los terrenos. • Ajuste las ruedas calibradoras con el tractor en una superficie nivelada plana. • Ajuste la segadora a la altura de corte deseada con la manilla de ajuste de altura.
2 Instalación de la placa del triturador de basura 1 • Levantar la pantalla del deflector (1) y colocar la placa del triturador de basura sobre la abertura. • Fijar el depósito de cierre anterior y posterior en el plano de trabajo de la segadora (2). ADVERTENCIA: no remover la pantalla del deflector y averiguar que esté apoyada sobre la placa del triturador de basura durante el uso. Seleccionar la modalidad de recogida o descarga.
3. Functional description. 3. Funktionsbeschreibung. 3. Description du fonctionnement. 3. Descripción del funcionamiento. 3. Funzionamento. 3. Beschrijving van functies 5 1 7 10 6 3 2 9 4 8 01986 Positioning of controls 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Anordnung der Bedienungseinrichtungen Light Switch Position. Throttle control. Brake and clutch pedal. Motion control lever. Connection/disconnection of the cutting unit. Quick lifting/lower of the cutting unit. Ignition lock. Parking Brake.
3 1 5 7 10 6 3 2 9 4 8 01986 Emplacement des commandes 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Comandi Interrupteur de commande des phares Commande des gaz (Accélérateur) Pédale d'embrayage et de frein Levier de commande dela transmission hydrostatique Embrayage/débrayage du carter de coupe Relevage et abaissement du carter de coupe Clé de contact/démarrage Frein de parking. Blocage/déblocage de la roue libre Starter. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Ubicación de los mandos 1. 2. 3. 4. 5. 6. 7. 8. 9. 10.
3 1. Light switch position 1. Lichtschalter 1. Interrupteur des phares 1. Interruptor de alumbrado 1. Interruttore luci 1. Schakelaar verlichting 2. Throttle control The throttle control regulates the engine revs and thus the rotation speed of the blades. = Full speed = Idling speed 2. Gashebel Mit dem Gashebel wird die Drehzahl des Motors und damit die Drehgeschwindigkeit des Mähaggregats geregelt. = Vollgas = Leerlauf 2.
3 3. Pédale d'embrayage et de frein En appuyant sur cette pédale, la transmission se débraye et le frein entre en action simultanément. 3. Pedal de freno y de embrague Al apretarlo se frena el vehículo y al mismo tiempo se desa copla el motor deteniéndose la propulsión. 3. Brake and clutch pedal 3. Pedale freno/frizione When the pedal is pushed down the brake is applied and the motor is disengaged. Premendo il pedale il trattore si frena, il motore va in folle e cessa la trazione. 3.
3 5. Connection/disconnection of the cutting unit Move the lever forward to connect the drive to the cutting unit, whereby the drive belt is tensioned and the blades begin to rotate. If the lever is moved backwards the drive will be disconnected and the rotation of the blades slowed down by the action of the brake shoes on the pulley. 5. Ein- und Ausschalten des Mähaggregats Den Hebel nach vorn führen, um den Antrieb des Mähers ein-zukuppeln.
3 6. Relevage et abaissement du carter de coupe 2 Tirer sur le levier vers l'arrière (1) pour relever rapidement le carter de coupe lors du passage sur une surface accidentée. Pour le transport, le carter de coupe doit être dans sa position la plus élevée (relevé au maximum). Pour cela, tirer le levier vers l'arrière jusqu'à sa butée.
3 OFF ON START 7. Ignition Lock There are three different positions for the ignition key: OFF All electric current broken. ON Electric current connected. START Start motor connected. WARNING! Never leave the key in the ignition lock when leaving the machine on its own. 7.
3 8. Parking brake Connect the parking brake in the following way: 1. Press down the brake pedal to bottom position. 2. Move the parking brake lever upwards and hold in this position. 3. Release the brake pedal. To release the parking brake all that is necessary is to push down the brake pedal. 8. Feststellbremse Die Feststellbremse wie folgt ansetzen: 1. Bremspedal ganz durchtreten. 2. Feststellbremshebel nach oben führen und in dieser Stellung halten. 3. Bremspedal loslassen.
3 9. Blocage et déblocage de la roue libre Pour remorquer ou déplacer le tracteur sans l'aide du moteur, la commande de roue libre, qui se trouvesur le tablier arrière du châssis du tracteur, doit être tirée vers l'extérieur et bloquée dans cette position. 9. Acoplamiento y Desacoplamiento de Rueda Libre Para empujar o arrastrar su tractor sin la ayuda del motor, el botón de control de rueda libre debe ser tirado hacia afuera y puesto en su posición. 9. Inserimento/Disinserimento Rouote 9.
4. Before starting. 4. Maßnahmen vor dem Anlassen. 4. Avant de démarrer. 4. Antes del arranque. 4. Prima dell’avviamento. 4. Maatregelen vóór het starten. Filling up Reposición de combustible The engine should be run of pure (not oil mixed) unleaded petrol. Do not fill beyond the lower edge of the filling hole. Do not fill over max level. WARNING! Petrol is highly inflammable. Proceed with care and fill up with petrol outdoors. Do not smoke when filling with petrol or fill up when the engine is warm.
4 Nivel de aceite Oil level La tapa combinada para el llenado de aceite y para la varilla de nivel queda accesible después de haber levantado hacia adelante el capó del motor. El nivel de aceite del motor debe controlarse cada vez que se pone en marcha. Asegúrese de que la máquina está horizontal. Descenrosque la varilla y séquela. Vuélvala a colocar. Enrósquela. Quítela otra vez y lea el nivel de aceite. The combined oil refilling cap and the oil stick is accessible when the bonnet is lifted forwards.
5. Driving. 5. Betrieb. 5. Conduite. 5. Conducción. 5. Guida. 5. Rijden. Démarrage du moteur S'assurer préalablement, que le carter de coupe est en position de transport (c'est à dire : relevé au maximum) et que le levier d'embrayage et de débrayage du carter de coupe est en position "débrayée" (voir figure).
5 Pull out the choke control (if engine is cold). Den Kaltstarthebel herausziehen (nur bei kaltem Motor). Si le moteur est froid : Tirer la commande de starter. Extraer el estrangulador (únicamente si el motor está frío). Estrarre il comando dello choke (in caso di partenza a freddo). Trek de choke uit (geldt alleen indien de motor koud is). Warm motor: Push the gas control half-way to full gass position " ". Bei warmem Motor: Gashebel in die Vollgasstellung " schieben.
5 Amener la clé de contact sur la position "Démarrage" ("START"). REMARQUE! Ne pas laisser tourner le démarreur plus de 5 secondes à chaque fois. Si le moteur ne démarre pas immédiatement, attendre une dizaine de secondes avant d'effectuer une nouvelle tentative. Ponga la llave de encendido en la posición de arranque ”START”. NOTA! No haga funcionar el motor de arranque más de unos 5 segundos a la vez. Si el motor no arranca, espere unos 10 segundos antes de hacer otra tentativa.
5 • IMPORTANT! COLD STARTING FOR HYDRO COLD STARTING FOR HYDRO (BELOW 40°F[4°C]) - AFTER STARTING ENGINE AND BEFORE DRIVING, LET TRANSMISSION WARM UP FOR ONE (1) MINUTE BY PLACING MOTION CONTROL LEVER IN NEUTRAL (N) POSITION AND RELEASING CLUTCH/BRAKE PEDAL. • • WICHTIG! KALTSTARTEN FÜR MASCHINEN MIT HYDROSTATISCHEM GETRIEBE FÜR TEMPERATUREN UNTERHALB VON 40° (4°C). NACH DEM ANLASSEN DES MOTORS DAS GETRIEBE (1) MINUTE LANG AUFWÄRMEN LASSEN, BEVOR LOSGEFAHREN WIRD. HIERZU DAS SCHALTGETRIEBE IN.
5 • • • • • • • • • • Placer le tracteur sur une surface plane afin qu'il ne puisse pas rouler dans aucune direction. Le frein de stationnement doit être desserré pour effectuer les opérations suivantes. Débrayer la transmission en plaçant la commande de roue libre sur sa position de marche en roue libre (Se référer à la section "TRANSPORT" de ce livret). Démarrer le moteur et mettre la commande des gaz en position de ralenti. S'assurer que le frein de stationnement n'est pas serré.
5 NOTE! NOTA! The machine is equipped with a safety switch which immediately breaks the current to the engine if the driver leaves the seat with engine running and with the connection/ disconnection lever in position “connection”. La máquina tiene un interruptor de seguridad que corta la corriente al motor si el conductor sale del asiento con el motor en marcha y con la palanca de acoplamiento/ desacoplamiento en la posición de acoplamiento.
5 Cutting tips • • • • • • • • Clear the lawn from stones and other objects which can be thrown away by the blades. Localize and mark stones and other fixed objects to avoid collision. Begin with a high cutting height and reduce until the required cutting result is obtained. The cutting result is best with high engine speed (blades rotate quickly) and low gear (machine goes slowly).
5 ATTENTION! • • • Ne jamais utiliser un tracteur sur des pentes excédant 10°. Les risques de renversement étant alors très importants. Ne jamais rouler parallèlement à la pente du fait des risques de renversement. Toujours rouler perpendiculairement à la pente, aussi bien en montant, qu'en descendant. Ne jamais arrêter ou démarrer un tracteur en pente. ADVERTENCIA! • • • WARNING! • • • No conduzca por terreno de inclinación superior a 10°, pues hay riesgo de sobrepeso en la parte posterior.
5 Use the left side of the machine to cut close to trees, bushes and paths, etc. The blade cuts about 15 mm inside the edge of the cover. Die linke Seite der Maschine benutzen, um in der Nähe von Bäumen, Gebüsch, Gängen usw. zu mähen. Die Mähklinge mäht ca. 15 mm innerhalb der Haubenkante. Utiliser le côté gauche de la machine pour tondre à proximité des arbres, des arbustes, des allées, etc... La lame coupe à environ 15 mm en retrait du bord intérieur du carter.
5 ADVERTENCIA! WARNING! Nunca deje la llave de encendido en la máquina sin vigilancia, a fin de evitar aue niños u otras personas ajenas puedan arrancar el motor. Do not leave the ignition key in the machine when not in use to prevent children and other unauthorized persons starting the engine. WARNUNG! PERICOLO! Den Zündschlüssel niemals im Zündschloß sitzen lassen, wenn die Machine unbeaufsichtigt verlassen wird, damit nicht Kinder und unbefugte Personen den Motor anlassen können.
6. Maintenance, adjustment. 6. Wartung (Instandhaltung), Einstellung. 6. Entretien, réglages. 6. Mantenimiento, ajuste. 6. Manutenzione. 6. Onderhoud, afstelling. WARNING! ADVERTENCIA! Before servicing the engine or cutting unit the following shall be carried out: • Press down the clutch/brake pedal and engage the parking brake lever. • Put gear lever in neutral. • Move connection/disconnection lever to disengaged position. • Switch off engine. • Remove the ignition cable from the plug.
6 Cubierta del motor 1 • • • • • Levante la cubierta. Desenchufe el conector de cables de los faros delanteros. Colóquese delante del tractor. Mueva la cubierta hacia ambos lados, inclínela hacia delante y extráigala. Para volver a ponerla, debe introducir los ejes de giro en las ranuras correspondientes del chasis. Enchufe el conector de cables de los faros delanteros y cierre la cubierta. Cofano Motore • • • 2 (1) (2) • • Cubierta Conector de cables de los faros delanteros Sollevare il cofano.
6 Manutenzione Entretien NOTA: Effettuare interventi periodici di manutenzione, per conservare il trattore nelle migliori condizioni di esercizio. PERICOLO: Prima di ogni intervento di manutenzione, riparazione o ispezione, staccare sempre la candela per evitare messe in moto accidentali. Prima di ogni impiego: • Controllare l'olio e lubrificare se necessario i punti di articolazione. • Controllare che tutti i dadi, i bulloni, le viti e i perni siano posto.
6 Pour assurer l'entretien du moteur Se référer au manuel d'utilisation du moteur. Vidange de l'huile du moteur Retirer le bouchon (1) et placer le tuyau de vidange (2). Pour ouvrir la soupape de vidange, repousser légèrement la soupape en la faisant tourner dans le sens contraire des aiguilles d'une montre pour sortir du cran, puis tirer sur la soupape pour libérer l'huile.
6 DATI DI SERVIZIO Compilare ogni qualvolta si esegue un regolare servizio Necessità Ogni 8 ore Ogni 25 ore Cambio dell'olio (Senza filtro dell’olio)................................................ Ogni . 50 ore • Cambio dell'olio (Con filtro dell’olio) ....................................................................... Lubrificazione punti di articolazione ................................................... Controllo freni.............................................. • • Ogni .
6 Lame Per avere il migliore risultato di taglio, è necessario che le lame siano ben affilate. Sostituirle se usurate o danneggiate. A tale scopo utilizzare una lima o una mola. NOTA! E’ importante affilare le due estremità della lama in modo uniforme per non creare disequilibri. RIMOZIONE DELLE LAME: Sollevare la macchina per avere accesso alle lame. Disserrare il bullone a testa esagonale, la rondella elastica e la rondella piatta che fissano la lama.
6 40mm Brakes 1 2 The brakes are located inside the right rear wheel. The wheel should be dismantled for best access. • Press down the clutch/brake pedal and engage the parking brake. Bremse Die Bremse sitzt innerhalb des rechten Hinterrades. Für beste Zugänglichkeit ist das Rad auszubauen. • Kupplungs-/Bremspedal durchtreten und die Feststellbremse einschalten. 1. Measure the distance between the brake lever and the adjuster nut. 2. The distance should be 40 mm (1.56"). 3.
6 Depose du Carter de Coupe Effectuer l'intervention à partir du côté droit du tracteur. 1. Sortir la courroie d'entraînement de la gorge de la poulie motrice (1). 2. Retirer le petit ressort de tension (2), et décrocher le ressort d'embrayage des lames du coté du boulon ser vant d'axe à la poulie d'embrayage. 3. Retirer l'épingle (3), faire glisser le collier et repousser le guide à l'extrémité de la gaine pour le faire sortir du support. 4.
6 5. Remove the retainer springs (5), (6), (7) and axles. 6. Pull the lever for lifting/lowering the cutting unit backwards. 7. Pull out the cutting unit from the machine. IMPORTANT: If an attachment other than the mower deck is to be mounted on the tractor, remove the front links and hook the clutch spring into square hole in frame (8). 6 7 8 5. Die Federklammern (5), (6), (7) und die jeweiligen Bolzen ausbauen. 6. Hebel für Heben/Senken des Mähdecks zurückziehen. 7.
6 Assembly of the cutting unit • • Push in the cutting unit under the machine. The ejector opening should be to the right. Assemble in the reverse order to dismantling. Einbau des Mähdecks • • Mähdecks unter den Traktor schieben. Die Auswurfoffnung muß nach rechts. Der Einbau erfolgt in umgekehrter Reihenfolge. Mise en place du carter de coupe • • Pousser le carter de coupe sous le tracteur. Le déflecteur du canal d'éjection doit se trouver du côté droit.
6 Replacement of drive belt for cutting unit 1. Dismantle the cutting unit as described previously. 2. Work off the belt from the unit's left pulley and then from the other wheels. 3. Pull the belt away from the cutting unit. 4. The new belt is mounted in the reverse order. Check that the belt lies inside all the belt guides. Auswechsein des Treibriemens für das Mähaggregat 1. Mähdeck ausbauen. 2. Riemen vom derlinken Keilriemenscheibe des Mähdecks und danach von den übrigen Riemenscheiben abbauen. 3.
6 2 A 1 B Adjustment of the cutting unit 1. 2. 3. 4. A. In the direction of travel Check that the air pressure is correct in all four tires. Make sure that the machine is on a horizontal surface. Lift up the cutting unit to its highest position. Measure the distances A and B. To achieve best cutting results the cutting unit’s front edge (B) should be about 10 mm (0.375") lower than the back edge (A). Adjust in the following way to raise the back edge: 1.
6 REGLAGE TRANSVERSAL 1 • • Relever le carter de coupe au maximum. A partir du milieu de chaque extrémités latérales du carter de coupe, mesurer la distance du bord du carter par rapport au sol . • La distance (A) doit être la même des deux côtés à 6 mm près. • Si un réglage est nécessaire, ne l'effectuer que d'un seul côté en se référant à l'autre côté. • Abaisser ou soulever un côté du carter de coupe en ajustant la position de l'écrou de réglage de ce côté.
6 Cambio de correa propulsora Desmontar el equipo de corte del tractor. Aplicar el freno de estacionamiento y tirar hacia arriba de la correa para sacarla de la rueda libre (1), de la acoplamiento (2) y de la propulsora del motor (3). Introducir la correa entre dos aspas del ventilador y hacer girar éste a izquierdas hasta que queda libre la correa (4). 3 Sostituzione della cinghia di trazione 2 Smontare il tagliaerba.
6 REGOLAZIONE DELLA LEVA DI COMANDO DEL MOVIMENTO DEL MECCANISMO DEL CAMBIO 1 La leva di comando del movimento del meccanismo del cambio è stata impostata al momento della fabbricazione e non richiede pertanto ulteriori regolazioni.
6 TRANSAXLE COOLING ENFRIAMIENTO DEL TRANSEJE The fan and cooling fins of transmission should be kept clean to assure proper cooling. Do not attempt to clean fan or transmission while engine is running or while the transmission is hot. • Inspect cooling fan to be sure fan blades are intact and clean. • Inspect cooling fins for dirt, grass clippings and other materials. Las aletas de enfriamiento y el ventilador de la transmisión tienen que mantenerse limpios para asegurar el enfriamiento adecuado.
7. Ricerca guasti. 7. Het localiseren van fouten. De motor start niet 1. Er is geen benzine in de tank. 2. De bougie is defect. 3. De bougie-aansluiting is defect. 4. Vuil in carburateur of brandstofleiding. Il motore non parte 1. Manca il carburante. 2. Difetto di candela. 3. Collegamento della candela difettoso. 4. Sporco nel sistema di alimentazione e o nel carburatore. De startmotor trekt de motor niet 1. De accu is leeg. 2. Slecht contact tussen kabel en accupool. 3.
8. Rismessaggio. 8. Stallen. Al termine della stagione effettuare i seguenti interventi: • Pulire tutto il tagliaerba e particolarmente sotto il coperchio della falciatrice. Per le operazioni di pulizia, non utilizzare acqua ad alta pressione. L’acqua può infiltrarsi nel motore e nel sistema di trasmissione, riducendo quindi così il tempo di vita della macchina. • Ritoccare danni alla verniciatura per evitare ossidazione. • Cambiare l’olio del motore. • Vuotare il serbatoio della benzina.
DECLARATION OF CONFORMITY • The Manufacturer: Electrolux Home Products, 172 Old Elloree Road, Orangeburg, SC 29115, USA DECLARACIÓN DE CONFORMIDAD • El Fabricante: Electrolux Home Products, 172 Old Elloree Road, Orangeburg, SC 29115, USA Herby declares that the machinery described below; • Category......................Rotary Mower • Guaranteed Sound Power • Make.................................. Bestgreen Level ................................. 100 dB (A) • Type ..............................