ECD1 24Bi tUps ampl er192kHzDAC Owner ’ sManual ENG
Owner’s Manual ECD 1 24 Bit Upsampler 192kHz DAC Warning: To avoid risk of fire or electric shock, do not expose this appliance to rain or moisture. Verify line voltage before use. Do not remove cover. No user serviceable parts inside. Refer servicing to qualified service personnel. The warranty is void if the product is tampered with by non-authorised personnel. Use only authorised Electrocompaniet service center.
Unpacking the ECD 1 Immediately upon receipt of the ECD 1, inspect the carton for possible damage during shipment. The carton and packaging have been designed to provide the safest possible protection for the transport of your product. Unpack the unit carefully. Save all packaging materials for future shipment.
How to connect your system Please read this page carefully and follow page 8-10. Inputs All digital inputs are electrical equal, and will accept the following: RCA XLR OPTICAL (S/PDIF) (AES/EBU) (TOSLINK) Outputs Analogue outputs XLR RCA (BALANCED) (SINGLE ENDED) Digital outputs RCA and OPTICAL (S/PDIF,TOSLINK) Both outputs may be used simultaneous. The output will follow the selected input. The ECD 1 can be used as a switch for multi-channel source (DVD).
How to power up your system You should always power up your system the following way: Signal sources (CD player, tuner,dac etc.) first. Then turn on the preamplifier. Allow 30 seconds of preheating before you turn on the power amplifier. After switching on the power amplifier, there will be a 5 seconds delay before the speakers are connected. This will prevent large turn on/off transients to reach the speakers.
Technical Specification ECD 1 The following technical data were measured on randomized test objects and are typical data. All measurements are made at 120V / 240V // 50Hz / 60Hz Analog stage Output level (unbalanced).............................1,6 V Output level (balanced)..................................3,2 V Gain (unbalanced).........................................1.6 X (4 dB) Gain (balanced)...............................................3.2 X (10 dB) Maximum output (balanced).........................
If Service is needed Your dealer will have all relevant information regarding the service station in your area, and will ensure that your unit is serviced with minimum delay. It is our general policy to have your unit returned to you within five working days. This is an average time, and can vary locally, depending on the workload at that particular service station.
Connecting the audio components 1 3 2 OUTPUT RIGHT 1 3 2 TYPE ECD1 5 4 6 7 LEFT 1 = GND 2=+ 3=- Balanced 8 DIG 3 DIG OUT DIG 4 TEST 9 CAUTION: The removal of the top cover may cause electric shock. No user serviceable parts inside.Refer to authorized service personnel. Do not expose to moisture or rain. 2 3 1 DIG 1 DIG 2 11 10 DIG OUT MANUFACTURED BY: ELECTROCOMPANIET, NORWAY 15 12 13 14 16 17 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18.
Single ended 3 2 1 OUTPUT RIGHT 1 3 2 TYPE ECD1 5 4 6 7 LEFT 1 = GND 2=+ 3=- 8 DIG 3 DIG OUT DIG 4 TEST 9 CAUTION: The removal of the top cover may cause electric shock. No user serviceable parts inside.Refer to authorized service personnel. Do not expose to moisture or rain. 2 3 1 DIG 1 DIG 2 11 10 DIG OUT MANUFACTURED BY: ELECTROCOMPANIET, NORWAY 15 12 13 14 16 17 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18.
Connecting the audio components Multi 12 3 2 1 OUTPUT RIGHT 5 4 6 LEFT 1 = GND 2=+ 3=- 1 3 2 TYPE ECD1 8 7 DIG 3 DIG OUT DIG 4 TEST 11 10 9 CAUTION: The removal of the top cover may cause electric shock. No user serviceable parts inside.Refer to authorized service personnel. Do not expose to moisture or rain.
Madei nNor way W W W .ELECTRO CO M PANIET.