USER MANUAL GAS PATIO HEATER EQODHMSS EQODHMBL WARNING: FOR OUTDOOR USE ONLY OR IN WELL VENTILATED AREAS PLEASE KEEP THE MANUAL FOR FUTURE REFERENCE
CONTENTS SAFETY 3 PARTS LIST 5 ASSEMBLY 6 SECURING THE BASE 9 OPERATION 10 LEAK TESTING 11 GAS INFORMATION 11 MAINTENANCE 12 STORAGE 12 TROUBLESHOOTING 13 SPECIFICATIONS 14 SUPPORT 14 2
IMPORTANT SAFETY INFORMATION Please read this user manual before using this heater and keep it safe for future reference. ⚫ Read the following instructions carefully and be sure your patio heater is properly installed, assembled and cared for. Retain the instructions for future reference. ⚫ Failure to follow these instructions may result in serious bodily injury and/or property damage.
IMPORTANT SAFETY RULES • For use outdoors or in well ventilated areas. • A well ventilated area must have a minimum of 25% of the surface area open. • The surface area is the sum of the walls surface. • The use of this appliance in enclosed areas can be dangerous and is PROHIBITED. • Children and adults should be aware of the high operating temperatures of areas above the post when operating this heater. Children should be carefully supervised when in the vicinity of the heater.
PART LIST A B C I D J K E PART A B C D E F G H I J K L M DESCRIPTION Reflector Panel Reflector Plate Head Assembly Deck Ring Top of Housing (Preassembled) Door (Preassembled) Door Lock (Preassembled) Rear of Housing (Preassembled) Gas Pipe Hose & Regulator Post Base (Preassembled) Wheel Kit QUANTITY 3 1 1 1 1 1 1 1 1 1 1 1 1 F G H L M PART DESCRIPTION IMAGE QTY. PART DESCRIPTION IMAGE QTY.
PATIO HEATER ASSEMBLY Required Tools: Philip Screwdriver and Adjustable Spanner. Leak Detection Solution: One-part detergent and three parts water Before assembly, ensure all packing material and any transit protection is removed. Line up holes on the bracket of the wheel assembly (M) with the corresponding holes on base (L). Then insert M8 x 16 mm bolts (BB) through the holes. Hand tighten with the M8 flange nuts (AA). Be sure the wheel assembly (M) is parallel to the base (L).
Attach the Reflector Panels (A) together using the M6 x 8mm Screws (FF), Φ6 Washers (DD) and Cap Nuts (GG). Do not fully tighten at this point. GG Note: In order to achieve proper alignment of reflector sections, it may be necessary to loosen the preassembled bolts prior to assembly and retighten once complete. DD FF DD FF GG Attach the Reflector Plate (B) to the Reflector Panels (A) using M6 x 8mm Screws (FF), Φ6 washers (DD) and Cap Nuts (GG). Do not fully tighten at this point.
Attach the Reflector Assembly to the Head Assembly (C). Secure with cap nuts (GG) and Φ6 washers (DD). All bolts previously fitted can now be tightened but Do not over tighten! DD GG Insert the hose & regulator assembly (I/J) through top of housing (E) and Post (K), tighten gas pipe (I) to head assembly(C). Secure head assembly (C) to the post (K) using bolts M5 x 10 (HH), lock washer (JJ), and Φ5 washers (EE). Note: The control dial on head assembly (C) should be aligned with door (F).
Attach the regulator (J) to the gas cylinder (not included). Place the gas cylinder into the rear of the unit and close the door (F). Note: See instruction Gas requirement and Connecting to a gas cylinder before buying a gas cylinder. SECURING THE BASE Secure 3pcs base brackets to the base using preassembled 6pcs bolts M5 x 12 (KK), 6pcs Φ5 washers (EE) and 6pcs lock washers (JJ) firstly, then strike suitable hook bolts or raw bolts through the stand holes into the ground.
OPERATING INSTRUCTIONS BEFORE FIRST USE AND AFTER EVERY GAS CYLINDER CHANGE, THE GAS DELIVERY SYSTEM MUST BE PURGED OF AIR BEFORE IGNITING! TO DO THIS, TURN THE CONTROL DIAL ANTI-CLOCKWISE TO THE PILOT SETTING. PRESS THE DIAL IN AND HOLD FOR 1 MINUTE BEFORE ATTEMPTING IGNITION. TO LIGHT THE PILOT ⚫ Check all connections prior to each use. ⚫ Turn on gas supply at the bottle. ⚫ Press and turn the control dial anti-clockwise to the PILOT position, see right photo.
LEAK TESTING NEVER USE A NAKED FLAME TO CHECK FOR LEAKS. NEVER LEAK TEST WHILE SMOKING. The gas connections on this appliance are leak tested at the factory prior to shipment. This appliance needs to be periodically checked for leaks and an immediate check is required if the smell of gas is detected. • Make a soap solution using 1 part of washing up liquid to 3 parts water. The soap solution can be applied with a soap bottle, brush, or rag to the leak tested points shown in the figure above.
MAINTENANCE To enjoy years of outstanding performance from your heater, make sure you perform the following maintenance activities on a regular basis: • • • Keep exterior surfaces clean. Use warm soapy water for cleaning. Never use flammable or corrosive cleaning agents. While washing your unit, be sure to keep the area around the burner and pilot assembly dry at all times. If the gas control is exposed to water in any way, DO NOT try to use it. It must be replaced. • Airflow must be unobstructed.
TROUBLESHOOTING PROBLEM Pilot won’t light Pilot won’t stay lit Burner won’t light Burner flame is low Note: Do not operate heater below 5℃(40°F) Emitter glows uneven Note: Bottom 2.
SPECIFICATIONS Product Name Patio Heater Model EQODHMSS, EQODHMBL Country Code Category Gas Pressure(mbar) BE-CY-CH-CZ- BG-HR-CH-CY-DK- FR-ES-GB-GR- EE-FI-GR-HU-IT-IS- CZ-FR-GB- IE-IT-PT-SK-SI- LT-LV-MT-NL-NO-PT- GR-IE-PT TR SE-SI-SK-RO-TR I3+(28-30/37) PL AT-CH-DE AT-CH-DENL I3B/P(30) I3P(37) I3B/P(37) I3B/P(50) I3P(50) G30 G31 G30/G31 G31 G30/G31 G30/G31 G31 28-30 37 30 37 37 50 50 Heat input 12.5KW 12KW 13.5kW 12.