User's Manual

ManualsBrandsElec-Tech International ManualsElectronicsMotion Sensor

Item/unit Parameter

Operating voltage 120V /60Hz

Switched power 200W (capacitive)

Standby power <0.5w

Warmming-up time 20s

Detection area 10%/50%/75%/100%, can be customized

Hold time 5S/90S/5min/15min, can be customized

Daylight threshold 2~50lux disable

Microwave frequency 5.8GHz+/-75MHz

Microwave power <1mw

Detection range Max. (oxH): 10m x 6m

Detection angle 30°～150°

Mounting height Max.6m

Operating temperature -20°C～70°C

IP rating IP20

Certificate ETL FCC



IntheendwewillonlyneedEnglishandSpanishfortheUS. WewilldoaseparateSpanish

IM. TheIMforthemotionwrapisincluded. Refertothatsowearetellingthesamestory

withregardtopersonallyadjustingthesensor. Thisisnotaneasy

conceptformanypeople

tograspsoyouhavetokeepaskingyourselfasyouwritethese“canIunderstanditsimply”?



Debcanyouputyourmarketingexpertiseonthisafterthenextdraft?



MotionSensorSettings



 Youcanadjustthesettingsfordetectionarea,holdtimeanddaylightsensitivity

shouldyouwishto. Thesensorcomesfactorypre‐setatthemostpopularsettings. To

adjustyou’llneedtosimplymovethedipswitchesaccordingtothesettingyou

desire. Pleaserefertothetable below.





InstallationOptions



Thissensorisdesignedtoworkwithbothselectlinkablepluginfixturesandalsowithboth

LEDandFluorescentfixtur esthatutilizeadirectwireconnectionmethod. 

Mountinginlinetoalinkable LEDfixture

Turnpoweroff

5.79GHz

Summary of content (5 pages)

PAGE 1
Item/unit Operating voltage Switched power Standby power Warmming-up time Detection area Hold time Daylight threshold Microwave frequency Microwave power Detection range Detection angle Mounting height Operating temperature IP rating Certificate Parameter 120V /60Hz 200W (capacitive) <0.5w 20s 10%/50%/75%/100%, can be customized 5S/90S/5min/15min, can be customized 2~50lux disable 5.79GHz 5.8GHz+/-75MHz <1mw Max. (oxH): 10m x 6m 30°～150° Max.
PAGE 2
b. The sensor will mount between your power cord end and the fixture. (the drawing goes here) The sensor notes which end is power In and which is power Out (show drawing of both here) Power in: c.
PAGE 3
d. Use the small male to male connector provided to make the connection on the power out end of the sensor by inserting it. Once the connector is in the sensor simply push it into the power end of the fixture (show drawing here) e. Next simply insert the power cord to the power in end of the sensor. Make sure both connections fit securely f. 2. Turn the power on. Make sure the pull chain is in the on position Mounting via Direct Wiring method a. Turn power off b.
PAGE 4
c. Use only the lock nut for that size d. Prepare the fixture by removing the lens if needed and then remove the knockout where you wish to mount the sensor. e.
PAGE 5
by making the connection with the wire nuts provided . Important to note there that the lock nut should be on the inside of the fixture wall with the wires coming through the middle (insert drawing here) (no wire nuts in my sample you sent, please add to cover all wires) f. Once the connections are made insert the threaded end into the hole completely and tighten the lock nut down by hand. For a firm fit gently use pliers to snug the lock nut down g. Replace the lens if needed. h.