Instruction Manual from software version 1.0 (instruction version 1.
This side is intentionally unlabelled. Elation Lighting www.elationlighting.
Table of contents 1 Description of Device..........................................................................................................7 1.1 Safety Instructions.......................................................................................................8 2 Preparation and Installation..............................................................................................9 2.1 Mounting..............................................................................................
3.11 Error and Information Messages...........................................................................20 4 DMX Channel Selection (DMX Protocol).......................................................................22 5 Change the Lamp...............................................................................................................24 5.1 Safety Regulations....................................................................................................24 5.
INTRODUCTION: Congratulations, you have just purchased one of the most innovative and reliable lighting fixtures on the market today! The Power Wash 575E™, has been designed to perform reliably for years when the guidelines in this booklet are followed. Please read and understand the instructions in this manual carefully and thoroughly before attempting to operate this unit. These instructions contain important information regarding safety during use and maintenance.
WARRANTY REGISTRATION: The Power Wash 575E™ carries a two year (730 days) limited warranty. Please fill out the enclosed warranty card to validate your purchase. All returned service items whether under warranty or not, must be freight pre-paid and accompany a return authorization (R.A.) number. The R.A. number must be clearly written on the outside of the return package. A brief description of the problem as well as the R.A.
1 Description of Device 1 4 1. Moving Head 2. Carrying handles 3. LED- Display 4. Arm 3 5. Camlock system 2 5 6. Software-Update connector 8 9 DMX IN 15 DMX OUT 7. Microphone- Intensity 8. DMX- Input 1.Ground 2.Data 3.Data + Min Max Mic Sensiti vity Software Update 9. DMX- Output 10. Fan (air inlet/outlet) 11. Power On/Off 7 10 6 10 12. Mains supply (Powercon) 15 13 14 Lamp Fuse Electronic Fuse Power input: 90 - 260V AC, 50 / 60Hz POWER 13. Fuse lamp 14. Fuse electronics 15.
1.1 Safety Instructions T h e POWER WASH 575E is a High-Tech Product. To guarantee a smooth operation, it is necessary to keep following rules. The manufacturer of this device will not take responsibility of damages through disregard of the information in this manual. Warranty adjustments will be cancelled. 1. Make sure before putting into operation, that the fan and the air inlets are clean and not blocked by anything. 2. Attention: Don’t touch the device during the operation.
2 2.1 Preparation and Installation Mounting The POWER WASH 575E is fully operational whether it hangs or is mounted to the wall. It can also be operated while standing on the floor. Keep a safety distance of 0.5 m towards any easy inflammable materials (decoration etc.). Install a safety wire that can hold at least 10 times the weight of the fixture. Never use the carrying handles for secondary attachment.
a) Camlock system: This system allows you a fast and efficient setup of clamps. Attach the two camlocks to designated position on the backside of the case and close the locks by turning them 90°. Verify the secure fit of the camlock system. The clamps themselves are directly attached permanently on the camlocks. 90° b) Use two clamps direct on the backside of the POWER WASH 575E to mount the unit on a truss (each two opposite threads max. M10x20). 4x M10x20mm 4x Camlock 2.
2.3 Connections 2.3.1 Power supply Electronic ballast with: ~90 - 260 Volt, 50 - 60 Hz, earth contact type plug - Powercon Connected load 780W <=> 3.8 A (blind current compensation). Please see printing on the case for the right electronic supply! 2.3.2 DMX DMX 512 Standard input/output. See also printing on the case for the right pin assignment. [+] = Pin 3 / [-] = Pin 2 / [Ground] = Pin 1 The DMX- Addressing starts at the DMX- Address [001]. 2.
The Menu Field D001 TEST AUDI Level 2 Level 3 ASLW AFST MSTR SVPT SIZE LAMP fl DOWN - UP ‡ RESE TIME FCOL RPAN RTLT SPEC POWR LA1 LA2 MANU LAAU DLOF DMXI DISP TEMP FANS ADJU Elation Lighting D ON REV HIGH REG LOOF LOHI CODE xxxx CYAN MAGE YELL COLO BSPR MODE ENTER DOWN Display MODE Level 1 MODE ENTER DOWN UP DOWN ENTER You’ll find the control board on the side part of the base. It allows you to make all necessary adjustments of the POWER WASH 5 7 5 E .
COAD DFSE FEED EFLG 3.
3.2 The Test Program (TEST) test The Test-Program allows you to run a complete self test procedure of all functions. Press Enter to confirm or Mode to cancel. 3.3 The Audio Program (AUDI) Audi The Audio-menu allows you to run a stand alone audio program. This chaser can run either fast or slow. AFST : Every sound impulse on step of the chaser. Aslw: Every second sound impulse one step of the chaser. Additional you can choose a basic position for this audio chaser.
3.5 Reset (RESE) RESE Press the Enter-key to run a reset of all fixture functions (RST is shown in the display). 3.6 Running time of lamp and unit (TIME) TIME By this option can read out three different running times of the fixture. POWR Running time of the fixture (no destructible). LA 1 Running time of the lamp (erasable). Push the Up/Down-keys at one time to delete this running time. LA 2 3.7 Running time of the lamp (no destructible).
3.10 Special Functions (SPEC) SPEC This menu allows you to enter further special functions of the POWER WASH 575E. In detail they are: 3.10.1 Manual Drive (MANU) MANU This function allows you to drive all the fixture functions manually. Select the desired function with the Up/Down-keys and confirm with Enter. Now choose the desired value with the Up/Down-keys and confirm again with Enter or cancel and return to the menu with the Mode-key.
If you have chosen off you have the possibility to start the lamp either via DMX or direct at the POWER WASH 575E in the Lamp menu. 3.10.3 Lamp Off via DMX (DLOF) DLOF This function enables to switch off the lamp via DMX or not. Use the Up/Down-keys to select ON if you want to switch off the lamp via DMX or Off if you don't want this function. Press Enter to confirm or Mode to cancel and return to the menu.
3.10.5 Display (DISP) DISP Use this function to choose between different display indications. Use the Up/Down-keys to select desired function and press Enter to confirm or Mode to cancel and return to the menu. D ON Display On/Off (If you've chosen off, the display will go out within 15 seconds after the last input. The next key touch will reactivate the display). REV Turn around the display. Note: You can also do this by pushing the Up/Down-keys at the same time. 3.10.
exceeds max. inside temperature, then the POWER WASH 575E automatically switch from low to high fan speed. In addition to these settings, you can set to fan speed to minimum via DMX (Special channel, DMX value 224..229). This will last until a temperature of 90° is reached. 3.10.8 Adjustments and Calibrations (ADJU) ADJU By this function you can adjust and calibrate the positions of the different wheels and other motors. This can be necessary after a service or repair work.
MAGE YELL - 99 - + 99 - 99 - + 99 Coarse adjustment of the Magenta color wheel Coarse adjustment of the Yellow color wheel 3.10.9 Default Settings (DFSE) DFSE Press Enter to reset all fixture personalities (not the adjusted functions) to the default values. On the display will appear ok to indicate that the defaults are set. Function DMX Address Pan reverse Tilt reverse Automatic lamp on Lamp on via DMX Display Cooling fan Feedback 3.10.
minutes after having switched off (lamp too hot). The message will appear on the display if the lamp doesn’t ignite within 20 seconds. The fixture will store this command and automatically ignite the lamp after 5 minutes. IG E When igniting the lamp, the electronic ballast will examine whether the lamp ignited or not. If the lamp does not ignite within 20 seconds, the igniting sequence is broken off. Now approx. 2 minutes are waited, until a renewed ignition attempt is started automatically.
4 DMX Channel Selection (DMX Protocol) Channel Function 1) PANcoarse 2) PAN-fine 3) Tiltcoarse 4) Tilt-fine 5) Color* 0 .. 530° Time and Value DMX HEX % 0..255 00..FF 0..100 0..255 0..255 00..FF 00..FF 0..100 0..100 Low- Pos … High- Pos + 1,1° (16 Bit) open (fast) Chaser from color to color max.
Channel Function Time and Value Shutter open Lamp ON (ignition) 10) Dimmer Dimmer closed (0%) Dimmer 1%...99% movement time 0,3 Sek.
Channel Function Time and Value lying eight size / phase see also PAN random movement size see also PAN 15) Speed Pan/Tilt Pan/Tilt relative movement Pan/Tilt slow – fast Use this channel 14) also for the speed of the movements (channel 13). Lampe ON Shutter open Pan Min. 530° = 200 s Pan Max. 530° = 2.65 s Tilt Min. 285° = 110 s Tilt Max. 285° = 1.8 s Lampe OFF Channel 9 ( min. 3 sec. ) (only if shutter is closed, channel 9 = 0 ..15) DMX HEX % 192..22 3 224..25 5 0..01 02..255 C0..DF 76..
lamp screws. The lamp filler neck must not in the direction lamp or lenses. Attention: Use only the original lamp type! 6. Pull the lamp holder safely back in the shaft and close the four screws. 7. The running time of the lamp LA1 can be reseed in the Time Menu. 6 Maintenance and Cleaning the POWER WASH 575E It is absolutely essential that the fixture is kept clean and that dust, dirt and smokefluid residues must not built up on or within the fixture.
Moveable parts yearly suitable fatty oil Attention: • Never let optical parts come into contact with oil or fat. • Before running the fixture wait until all parts are dried up. 6.3 Cleaning the Optical System 1. Pull out the main plug! 2. Wait min. 20 minutes after the last operation to cool down the fixture. 3. Open the upper shell of the head casing by loosening the 4 Phillips screws. Two on the front side and two on the back side of the head. 4. Do the work as explained in the list above. 5.
Standard DMX-512, 3 pole XLR; [+] = Pin 3 [-] = Pin 2 [Ground] = Pin 1. The DMX- addressing starts at the DMX- address [001]. Pan / Tilt Pan- movement 530° in max. 2,65 seconds, 16 bit resolution Tilt- movement 280° in max. 1,68 seconds, 16 bit resolution Weights and measures Width of the base 380 mm Length of the base 390 mm height (head vertical) 520 mm Weight (net) 19 kg Elation Lighting www.elationlighting.
2 YEAR (730 DAYS) LIMITED WARRANTY A. Elation Professionals ® hereby warrants, to the original purchaser, Elation Professionals ® products to be free of manufacturing defects in material and workmanship for a period of two years (730 days) from the date of purchase. This warranty shall be valid only if the product is purchased within the United States of America, including possessions and territories.
F. No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with products described above. Except to the extent prohibited by applicable law, all implied warranties made by Elation Professionals® in connection with this product, including warranties of merchantability or fitness, are limited in duration to the warranty period set forth above.
8 Index A M Audio.......................................................... 11 Maintenance .............................................. 21 Measures.................................................... 23 Mounting...................................................... 7 B BGV C1 ........................................................ 7 C Circumference............................................. 22 Cleaning ..................................................... 22 D Description of Device.............
Elation Professional 4295 Charter Street Los Angeles, CA. 90058 323-582-3322 / 323-582-3108 fax www.ElationLighting.com / info@ElationLighitng.com Elation Lighting www.elationlighting.