POWER SPOT 700 II User Manual Revised 5/14/08 - visage
Power Spot 700 II™ ©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.
Power Spot 700 II™ Table of Contents 1. Introduction ..............................................................................................................5 Unpacking .........................................................................................................5 Customer Support .............................................................................................5 Discharge Lamp Precautions ............................................................................6 2.
Power Spot 700 II™ 8.9.8 Adjustments and Calibrations (ADJU) .................................................31 8.9.9 Default Settings (DFSE) .......................................................................32 8.9.10 Feedback (FEED) .................................................................................32 8.9.11 Fault Corrections (EFLD).....................................................................32 8.10 Error and Information Messages .................................................
Power Spot 700 II™ INTRODUCTION: Congratulations, you have just purchased one of the most innovative and reliable lighting fixtures on the market today! The Power Spot 700 II™, has been designed to perform reliably for years when the guidelines in this booklet are followed. Please read and understand the instructions in this manual carefully and thoroughly before attempting to operate this unit. These instructions contain important information regarding safety during use and maintenance.
Power Spot 700 II™ limited warranty. Please fill out the enclosed warranty card to validate your purchase. All returned service items whether under warranty or not, must be freight pre-paid and accompany a return authorization (R.A.) number. The R.A. number must be clearly written on the outside of the return package. A brief description of the problem as well as the R.A. number must also be written down on a piece of paper and included in the shipping container.
Power Spot 700 II™ Never open this fixture while in use! During the initial operation of this fixture, a light smoke or smell may emit from the interior of the fixture. This is a normal process and is caused by excess paint in the interior of the casing burning off from the heat associated with the lamp. This device falls under protection-class 1. Therefore it is essential that the device be grounded properly. All electrical connections must performed by qualified personal.
Power Spot 700 II™ 2. SAFETY INSTRUCTIONS The Power Spot 700 II™ is an extremely sophisticated piece of electronic equipment. To guarantee a smooth operation, it is important to follow the guidelines in this manual. The manufacturer of this device will not accept responsibility for damages resulting from the misuse of this fixture due to the disregard of the information printed in this manual. 1. Always be sure that the fan and the air inlets remain clean and are never blocked.
Power Spot 700 II™ 3.
Power Spot 700 II™ 4. GENERAL GUIDELINES This fixture is a professional lighting effect designed for use on stage, in nightclubs, in theatres, etc. Do not attempt operation or installation without a proper knowledge on how to so. This fixture was designed for indoor use only. Consistent operational breaks may ensure that the fixture will function properly for many years to come. Do not shake the fixture around. Avoid brute force when installing or operating the device.
Power Spot 700 II™ Transportation and Handling The POWER SPOT 700 II™ comes with two carrying handles built into the base. Always transport the fixture by these handles. Never lift or carry the POWER SPOT 700 II™ by the yoke (head assembly) this can seriously damage the unit and will void your manufactures warranty. Connections Power supply: Electronic ballast with: 90~260 Volts, 50~60 Hz, Grounded contact type plug – Neutrik Powercon Connected load 1000W <=> 4.5 A (blind current compensation).
Power Spot 700 II™ 5. FIXTURE LAYOUT 1. Moving Head 2. Carrying Handles 3. LED Menu Display 4. Head Tilt Lock 5. Omega Clamp 6. Ethernet Jack 7. 5-Pin DMX Out Connector 8. 5-Pin DMX In connector 9. Microphone Sensitivity 10. Build-In Microphone 11. Software-Update Connector 12. 3-Pin DMX Out Connector 13. 3-Pin DMX In Connector 14. Carrying Handle 15. Power On/Off 16. Lamp Fuse 17. Fan (air inlet/outlet) 18. Main Power Supply (Powercon) 19. Electronics Fuse ©Elation Professionals® Los Angeles, Ca.
Power Spot 700 II™ Side View - Menu and Display 20.4-Segment LED Menu Display 20 21 22 23 24 21. Mode Button 22. Enter Button 23. Up Button 24. Down Button 1. Head Assembly – The head assembly consist of the main output lens, and either the standard or CMY control module. 2. Carrying Handle – The fixtures includes two built-in carrying handles. Be sure to always handle the fixture by the built-in carrying handles.
Power Spot 700 II™ 7. 5-PIN DMX Output Jack (CMY Version Only) – This 5-Pin XLR jack is used to send an outgoing DMX signal. For best results this jack should be terminated if it is the last fixture in a DMX daisy-chain (see termination on page 20). 8. 5-Pin DMX Input Jack (CMY Version Only) - This 5-Pin XLR jack is used to receive an incoming DMX signal. 9.
Power Spot 700 II™ 17. Internal Cooling Fan – This fixture is equipped with two high-velocity variable speed fans mounted in the base to aid in the cooling process. These fans are designed to vary their velocity at different operating temperatures. When the fixture reaches a predetermined internal operating temperature the fans function at high speeds. The higher speeds provide better cooling associated with higher operating temperatures during long use.
Power Spot 700 II™ 6. MOUNTING AND INSTALLATION Cautions: For added protection mount the fixtures in areas outside walking paths, seating areas, or in areas were unauthorized personnel might reach the fixture. Before mounting the fixture to any surface, make sure that the installation area can hold a minimum point load of 10 times the device’s weight. Fixture installation must always be secured with a secondary safety attachment, such as an appropriate safety cable.
Power Spot 700 II™ Refer to regulations BGV C1 (formerly VBG 70) and DIN VDE 0711-217 for proper installation in Europe To ensure proper installation, only qualified staff should attempt installation. Mounting points Overhead mounting requires extensive experience, including amongst others calculating working load limits, a fine knowledge of the installation material being used, and periodic safety inspection of all installation material and the fixture.
Power Spot 700 II™ 90° b) Be sure to always use two cam locks mounted to the bottom of unit to ensure safe truss mounting (each two opposite threads max. M10x20). Secure the POWER SPOT 700 II™ Regardless of the rigging option you choose for your POWER SPOT 700 II™ always be sure to secure your fixture with a safety cable. The fixture provides a built-in rigging point for a safety cable on the underside of the fixture, be sure to use this point and never secure a safety cable to a carrying handle.
Power Spot 700 II™ 7. UNDERSTANDING DMX DMX-512: DMX is short for Digital Multiplex. This is a universal protocol used by most lighting and controller manufactures as a form of communication between intelligent fixtures and controllers. DMX allows all makes and models of different manufactures to be linked together and operate from a single controller. This is possible as long as all the fixtures and the controller are DMX compliant.
Power Spot 700 II™ chained and cannot be split, unless using an approved DMX splitter such as the Elation Opto Branch 4™ or DMX Branch/4™. Be sure to follow the above figure when making your own cables. Do not use the ground lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow the shield conductor to come in contact with the XLR’s outer casing. Grounding the shield could cause a short circuit and erratic behavior.
Power Spot 700 II™ DATA -). This fixture is inserted in the female XLR connector of the last fixture in your daisy chain to terminate the line. Using a line terminator (Elation part: DMX T PACK) will decrease the possibilities of erratic behavior. 5-Pin XLR DMX Connectors. Some manufactures use 5-pin XLR connectors for DATA transmission in place of 3-pin. 5-pin XLR fixtures may be implemented in a 3-pin XLR DMX line.
Power Spot 700 II™ DMX address will subsequently control all fixtures in the same fashion, in other words, changing the settings of one channel will affect all the fixtures simultaneously. If you set each fixture to a different DMX address, each unit will start to “listen” to the channel number you have set, based on the quantity of control channels (DMX channels) of each fixture. That means changing the settings of one channel will only affect the selected fixture.
Power Spot 700 II™ 8. FIXTURE MENU DOWN - UP RPAN RTLT DMOD SPEC Level 3 ASLW AFST MSTR SVPT SIZE POWR LA1 LA2 NORM EXT MANU LAAU DLOF DMXI DISP LHEA LBAS TEMP D ON REV MODE LAMP RESE TIME Level 2 MODE ENTER DOWN Display DOWN ENTER Level 1 D001 TEST AUDI MODE ENTER DOWN UP UP UP The control panel located on the side of the fixture allows you to access the main menu and make all necessary adjustments to the POWER SPOT 700™.
Power Spot 700 II™ FANS ADJU COAD DFSE FEED EFLG HIGH REG LOOF LOHI CODE xxxx COL1 COL2 GOB1 GOB2 GOB3 SH T SH B PRIS IRIS POFS TOFS CLRE ARES VTIL VTR1 VTR2 VTR3 DBUG CODE XXXX COL2 COL1 Reed out internal temperature Maximum cooling fan velocity Automatic cooling fan control Low cooling fan speed lamp off Use the code for entering the calibration menu (for authorized persons only) Calibration of the color wheel 1 Calibration of the color wheel 2 Calibration of the gobo wheel 1 Calibration of the go
Power Spot 700 II™ 2. Press the Mode button to access the main menu. Toggle through the menu by pressing the Up and Down buttons until the display shows D001. Tap the enter button to make changes to the address, the current three digit address will immediately begin to flash. 3. While the current three-digit address is flashing, use the Up and Down buttons to select adjust the address. Lock your new address into the unit’s memory by pressing the Enter button.
Power Spot 700 II™ 8.4 Lamp On/Off LAMP This function allows you to manually control the lamp operation. Access the lamp function in the main menu and use the use the Up and Down buttons to toggle between lamp On and lamp Off. Press the Enter button to confirm the operation or the Mode button to cancel and return to the main menu. (The lamp OFF command will only functions if and when the shutter is closed at the same time). 8.
Power Spot 700 II™ Mode button to cancel and return to the main menu. 8.8 Invert Tilt Movement RTLT This function allows you to invert all tilt movements. Use the Up and Down buttons to turn this function On and Off. Press the Enter button to accept the change or the Mode button to cancel and return to the main menu. 8.9 Special Functions SPEC This menu option accesses several special features and function of the POWER SPOT 700™. The SPEC sub-menu consists of several sub-menus.
Power Spot 700 II™ GOB2 GRT2 GOB3 SHUT 000 000 000 000 - 255 255 255 255 Gobo wheel 2 Gobo wheel 2 rotation Gobo wheel 3 DIMR FOCU ZOOM FRST PRIS IRIS SPEC MOVE SPED 000 000 000 000 000 000 000 000 000 - 255 255 255 255 255 255 255 255 255 Dimmer Focus Zoom Frost Prism (000 – 127) / Stop / Prism- rotation Iris Lamp Off, Reset, ... Movements Speed for Pan/Tilt Shutter/Strobe functions ~ Lamp will strike at a channel value of 255 if the dimmer channel is at a value of 255 (Open) 8.9.
Power Spot 700 II™ This function will display the DMX value of a channel in the LED as the fixture receives it. Use the Up and Down buttons to select desired channel and press Enter to read its value.
Power Spot 700 II™ 8.9.6 Fixture Temperature TEMP This function allows you to read out the actual fixture operating temperature. Press the Enter button to select this function or the Mode to button to cancel and return to the main menu. Normal operating temperature should range between 85˚C and 95˚C. Operating temperatures between 96˚C and 104˚C are considered critical.
Power Spot 700 II™ 8.9.8 Adjustments and Calibrations ADJU With this function you can adjust and calibrate the positions of the different wheels and other motors. This feature is reserved for a service technician and is sometimes required after a service or repair work. This function requires a service code only available to authorized service technicians.
Power Spot 700 II™ 8.9.9 Default Settings DFSE This function is used to restore all the factory default settings and presets. Press the Enter button to confirm this operation or the Mode button to cancel and return to the menu. When this operation is selected the LED will briefly readout ok, then return to the previous function. The chart below details the factory defaults.
Power Spot 700 II™ 8.10 Display Error and Information Messages HEAt IG E LAER This message appears if you try to switch on the lamp within 5 minutes after having switched off (lamp too hot). The message will appear on the display if the lamp doesn’t ignite within 20 seconds. The fixture will store this command and automatically ignite the lamp after 5 minutes. When igniting the lamp, the electronic ballast will examine whether the lamp ignited or not.
Power Spot 700 II™ 9. OPERATION Operating Modes: The Power Spot 700 II™ can operate in three different modes. This next section will detail the differences in the operating modes. • Stand-alone mode - The fixture will react to sound, chasing through the built-in programs. • Master/Slave mode - You can daisy chain up to 16 fixtures together to get a synchronized light show without the need of an external controller. The fixtures will react to sound chasing to synchronized light show.
Power Spot 700 II™ 9.2.2 Access the main menu and select the AUDI function, this will give you access to the audio submenu. See page 25 for the menu breakdown. 9.2.3 In the audio submenu choose the audio chase speed, fast or slow. Slow (ASLW) will trigger the chase sequence to every two beats, while fast (AFST) will trigger the chase impulse every beat. See page 25 for more details. 9.2.4 Be sure the Master (MSTR) function is switched “ON,“ and the SVPT function is switched “OFF.“ 9.2.
Power Spot 700 II™ With two exceptions; be sure the first unit in the chain is selected as the “master“ (MSTR) is turned on in the audio submenu. All other fixtures must be in “slave“ mode (SVPT) turned on in the audio submenu. ©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.
Power Spot 700 II™ 10. DMX CHANNEL TRAITS (DMX PROTOCOL) Channel Function Time and Value DMX HEX % 1) Pan 0..530° 0..255 00..FF 0..100 2) Pan-fine High-Pos ... High-Pos + 2.1° (16 Bit) 0..255 00..FF 0..100 3) Tilt 0..285° 0..255 00..FF 0..100 4) Tilt-fine High- Pos … High- Pos + 1.1° (16 Bit) 0..255 00..FF 0..100 5) Color 1 Open (fast) 0..1 00..01 0.2 (fast) Open / Color 1 (fast) 2..3 02..03 1.0 4..5 04..05 1.8 Color 1 / Color 2 (fast) 6..7 06..07 2.5 Color 2.
Power Spot 700 II™ Channel Function Time and Value DMX HEX % Color 2 / Color 3 (slow) 74..75 4A..4B 29.2 Color 3. Purple (slow) 76..77 4C..4D 30.0 Color 3 / Color 4 (slow) 78..79 4E..4F 30.8 Color 4. Blue (slow) 80..81 50..51 31.6 Color 4 / Color 5 (slow) 82..83 52..53 32.4 Color 5. Green (slow) 84..85 54..55 33.1 Color 5 / Color 6 (slow) 86..87 56..57 33.9 Color 6. Yellow (slow) 88..89 58..59 34.7 Color 6 / Color 7 (slow) 90..91 5A..5B 35.5 Color 7.
Power Spot 700 II™ Channel Function Time and Value DMX HEX % Color 4 / Color 5 (fast) 18..19 12..13 7.3 Color 5. Yellow (fast) 20..21 14..15 8.0 Color 5 / Color 6 (fast) 22..23 16..17 8.8 Color 6. Light Green (fast) 24..25 18..19 9.6 Color 6 / Color 7 (fast) 26..27 1A..1B 10.4 Color 7. CTO (fast) 28..29 1C..1D 11.2 Color 7 / Color 8 (fast) 30..31 1E..1F 12.0 Color 8. CTC (fast) 32..33 20..21 12.7 Color 8 / Color 9 (fast) 34..35 22..23 13.5 Open (fast) 36..63 24..
Power Spot 700 II™ Channel Function Time and Value Color Rotation STOP DMX HEX % 128..129 80..81 50.1 Color rotation, slow-fast, CW Min. 1.4 turns/h 130..191 82..BF 51..75 Color rotation, fast-slow, CCW Max. 2.9 turns/sec. 192..253 C0..FD 76..98 Audio color chaser slow Each 4 254 FE 99 255 FF 100 0..7 0..7 0..2.9 8..15 8..F 3..5.9 16..23 10..17 6..8.9 Gobo 4 (fast) 24..31 18..1F 9..11.9 Gobo 5 (fast) 32..39 20..27 12..14.9 Gobo 6 (fast) 40..47 28..2F 15..17.
Power Spot 700 II™ Channel Function 8) Gobo 1 Gobo Position 0 ... 540° Posi./Rot Gobo Rotation STOP Time and Value DMX HEX % 0..127 00..7F 0..49 128..129 80..81 50 Gobo Rotation. Slow-fast. CW Min. 2.0 turns/h 130..191 82..BF 51..75 Gobo Rotation. Fast-slow. CCW Max. 3.8 turns/sec. 192..253 C0..FD 76..100 Audio Gobo Rotation. Slow Each 4 254 FE 99 255 FF 100 0..7 0..7 0..2.9 8..15 8..F 3..5.9 16..23 10..17 6..8.9 Gobo 4 (fast) 24..31 18..1F 9..11.
Power Spot 700 II™ Channel Function Time and Value DMX HEX % 0..127 00..7F 0..49 128..129 80..81 50 new gobo 10) Gobo 2 Gobo Position 0 ... 540° Posi./Rot Gobo Rotation STOP Gobo Rotation. Slow-fast. CW Min. 2.0 turns/h 130..191 82..BF 51..75 Gobo Rotation. Fast-slow. CCW Max. 3.8 turns/sec. 192..253 C0..FD 76..100 Audio Gobo Rotation. Slow Each 4 254 FE 99 255 FF 100 0..3 00..03 0..1 4..7 04..07 2..3 8..11 08..0B 3..4 Gobo 4 (fast) 12..15 0C..0F 5..
Power Spot 700 II™ Channel Function Time and Value DMX HEX % Gobo rotation, slow-fast, CW Min. 1.4 turns/h 130..191 82..BF 51..75 Gobo rotation, fast-slow, CCW Max. 1.0 turns/sec. 192..253 C0..FD 76..98 Audio gobo chase, slow Each 4 254 FE 99 255 FF 100 Shutter closed 0..15 00..0F 0..6 Random Strobe (different pattern) 16..31 10..1F 7..11.9 32..47 20..2F 12..12.9 48..63 30..3F 13..25 64..239 40..EF 26..93 240..255 F0..FF 94..100 0..3 0..3 0..1 4..251 4..FB 2.
Power Spot 700 II™ Channel Function Time and Value HEX % Ascend with Shutter Slow - fast 192..207 C0..CF 75..81 Descend with Shutter Slow - fast 208..223 D0..DF 82..87 Pulse - effect Slow - fast 224..239 E0..EF 88..93 Ascend - descend effect Slow - fast 240..253 F0..FD 94..99 254..255 FE..FF 100 0..15 00..0F 0..6 16..31 10..1F 7..12 32..47 20..2F 13..18 48..63 30..3F 19..24 64..111 40..6F 23..43 112..127 70..7F 44..50 128..143 80..8F 51..56 144..175 90..
Power Spot 700 II™ Channel Function PAN PAN PAN Time and Value DMX HEX % 1 90° 02..03 02..03 1.0 1 180° 04..05 04..05 1.7 1 270° 06..07 06..07 2.5 2 0° 08..09 08..09 3.3 2 90° 10..11 0A..0B 4.1 2 180° 12..13 0C..0D 4.9 2 270° 14..15 0E..0F 5.7 3 0° 16..17 11..11 6.5 3 90° 18..19 12..13 7.3 3 180° 20..21 14..15 8.0 3 270° 22..23 16..17 8.8 4 0° 24..25 18..19 9.6 4 90° 26..27 1A..1B 10.4 4 180° 28..29 1C..1D 11.2 4 270° 30..
Power Spot 700 II™ Lamp ON Shutter open Lamp OFF Channel 12 Lamp OFF (min. 3 sec.) if Shutter closed '000' Channel 19 and Channel 12 Channel 19 Reset ©Elation Professionals® Los Angeles, Ca. - 240..25 F0..F 94..10 5 F 0 230..24 6E..9 92..97 9 F 0 0 0 250..25 FA..F 98..10 5 F 0 wwww.ElationLighting.
Power Spot 700 II™ 11. LAMP REPLACEMENT For a proper and safe lamp change, please read this chapter carefully and follow all instructions. Safety Regulations • Pull out the main plug! • Wait min. 20 minutes after the last operation to cool down the fixture. • Don’t touch the bulb of the lamp with bare fingers (this can cause damages. • Before you put the POWER SPOT 700™ into operation close the casing, otherwise your retina can be hurt! • Replace the lamp with an approved replacement type.
Power Spot 700 II™ fasteners will remain connected to the lamp socket cover. 5. Gently remove the old lamp from it’s socket. If the old lamp has exploded be sure to remove all of the old lamp fragments to prevent damage to the internal components. 6. Insert the new lamp securely, locking the lamp in place as illustrated in the diagram to the left. Orientate the lamp filler tube towards the backside of the reflector. Before reassembling the unit, be sure the new lamp is securely seated in the lamp socket.
Power Spot 700 II™ 2. Move lamp with setscrew “A” upward/downwards until this hotspot is in the center of the beam projection. 3. Use setscrew “B” once again to move the lamp forwards and backwards until you've reached the most even beam projection. Note: A slight hotspot will always remain and is conditional to the optical path. ©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.
Power Spot 700 II™ 12. FUSE REPLACEMENT Caution: Always replace with the exact same type fuse, unless otherwise specified by an authorized Elation® service technician. Replacing with anything other than the specified part can damage your unit and will void your manufactures warranty. Warning: If you continue to blow fuses, STOP using the fixture. Contact customer support for further instructions, you may have to return the unit for servicing. Continuing to use the unit may cause serious damage.
Power Spot 700 II™ 13. OPTICAL EFFECTS MODULE The Power Spot 700 II is equipped with an optical effects module that can be easily removed for cleaning, service, and gobo/color exchange. Please follow the procedures below for proper removal and service of the effects module. 13.1 Safety considerations • Always remove main power before attempting any type of service procedure.
Power Spot 700 II™ Data Bus 2x 4) Loosen the two locking thumbscrews on the left and right side of the optical effects module (please do not attempt to remove the thumbscrews completely). Once the thumbscrews have been loosened push them inwards towards the center of the head while gently pulling the effects module straight out. You may use the metal support plates to grasp and pull the effects module out. See the illustration below; Attention: The effects module reset between two lateral tracks.
Power Spot 700 II™ means to grasp the module. 5) To access the internal components of the module loosen the three securing thumbscrews illustrated below. Once these screws are lose you may place the module on a flat and open the unit up as if it were a book. This will allow access the all the gobos and colors so they may be changed or cleaned. 6) For Gobo and Color replacement please see the next section. 7) To replace module; a) Fold up the module and fasten the three retaining thumbscrews.
Power Spot 700 II™ b) Insert the effects module back in to the fixture and the two lateral tracks. Push it carefully down until the two locking thumbscrews snap in place and hand tighten the retaining thumbscrews. c) Connect the "Data Bus" cable into the proper corresponding socket. d) Seal the cover in reverse order. ©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.
Power Spot 700 II™ 14. CHANGING/REPLACING GOBOS/COLORS Before attempting to change any gobos or color be sure to follow the effects module removal process as described in the previous section (section 13) of this manual. The POWER SPOT 700 II includes both Aluminum (thickness = 0.3 mm) and Glass (thickness = 1.1 - 3.0 mm) gobos (outside diameter 26.9 mm, viewable image size 23 mm). There is one rotating Gobos wheel (user replaceable gobos) and one fixed Gobo wheel (non replaceable gobos). 14.
Power Spot 700 II™ Attention: Custom gobos that contain company logos and text must also be orientated properly to ensure proper display of the custom image. The readable side must be mounted towards the lamp. In the illustration below, notice that the text is readable in the example on the left and mirrored in the example on right. The illustration below details proper gobo placement.
Power Spot 700 II™ 14.2 Changing Gobos 1) Be sure the effects module is removed and opened as detailed in the previous section of this manual. 2) Genteelly lift and pull the gobo holder out of the center part of the wheel hub to remove the individual holder. See the left image below. 3) Once the gobo holder has been removed the Gobo itself can be replaced by remove the centric spring with a small screwdriver or gripping pliers.
Power Spot 700 II™ Power Spot 700 II Gobo Wheels Special Notice: If you use glass gobos, the non-vaporized side must be fitted towards the lamp direction. Gobo wheel 1 with rotating Gobos Gobo wheel 2 with rotating Gobos Fixed Gobo wheel ©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.
Power Spot 700 II™ 15. MAINTENANCE AND CLEANING It is absolutely essential that the fixture is kept clean and dust, dirt and smoke-fluid residues do not built-up on the surface or within the fixture. Residue build-up may cause the fixture's light output to be significantly reduced. Regular cleaning will not only ensure the maximum light output, but will also allow the fixture to function reliable throughout its life.
Power Spot 700 II™ Inside lens Monthly Soft cloth no glass cleaner Fan and air channel Monthly Vacuum cleaner, airbrush, etc. Reflector Never Lamp Never Moveable parts Yearly Suitable Lubricant Caution: 1. Never allow the optical parts to come in contact with oil, dirt, or grime. 2. Allow all parts to dry completely before attempt operation. 3. Never clean the aspheric lens with water or other cleaners.
Power Spot 700 II™ 16. TWO YEAR (730 DAYS) LIMITED WARRANTY A. Elation Professionals® hereby warrants, to the original purchaser, Elation Professionals® products to be free of manufacturing defects in material and workmanship for a period of two years (730 days) from the date of purchase. This warranty shall be valid only if the product is purchased within the United States of America, including possessions and territories.
Power Spot 700 II™ F. No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with products described above. Except to the extent prohibited by applicable law, all implied warranties made by Elation Professionals® in connection with this product, including warranties of merchantability or fitness, are limited in duration to the warranty period set forth above.
Power Spot 700 II™ 17. PHOTOMETRIC DATA ©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.
Power Spot 700 II™ 18. DIMENSIONS ©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.
Power Spot 700 II™ 19. TECHNICAL SPECIFICATION Power supply Power consumption Fuse protection Lamp Type Live time Color temperature Luminous flux 90 ~ 260V, 50 ~ 60 Hz 1000 Watt, 4.
Power Spot 700 II™ Standard DMX-512, 3 pole XLR; [+] = Pin 3 [-] = Pin 2 [Ground] = Pin 1. The DMX- addressing starts at the DMX- address [001]. Pan / Tilt Pan - movement 530° in max. 2.65 seconds, 16 bit resolution Tilt - movement 280° in max. 1.68 seconds, 16 bit resolution Weights and measures Width of the base Length of the base Height (head vertical) Weight (net) 490 mm (19.3”) 380 mm (15”) 646 mm (25.5”) 28.
Power Spot 700 II™ 1. INDEX A Adjustments.......................................... 23 aspheric lens .......................................... 40 I Injury of the retina ..................................... 7 M Maintenance ........................................... 39 Measures ................................................ 41 Mounting................................................ 11 B BGV C1 .................................................. 11 Blind current compensation ....................
Power Spot 700 II™ Elation Professional 6122 S. Eastern Ave. Los Angeles, Ca. 90040 www.ElationLighting.com / info@ElationLighitng.com ©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.
